EFFECTS OF EXTRUSION BLOW MOLDING INTERNAL COOLING ...

More documents

Recommendations

Info

Figure 10. Finish Dimensions Volume: Containers were weighed empty, and then filled with water conditioned according to ASTM C2911-94 and weighed again. Container volume was calculated as follows: Bv ( mL) = ( B f − Be ) / 0.997 Bottle overflow Capacity Tolerance with a volume between 384 and 531mL is ±11mL. Body Dimensions: Width is an average of the measurements at the parting line and then rotated 90 degrees. The width is measured using calipers 3” from the bottom of the container. 26
Table 5. Bottle Body Dimension Tolerances (ASTM D 2911-94) Range of Dimensions Width Tolerance inches inches 0 up to but not including 1 0.03 1 up to but not including 2 0.05 2 up to but not including 4 0.06 4 up to but not including 6 0.08 6 up to but not including 8 0.09 8 up to but not including 10 0.11 Body Wall thickness: Wall thickness was measured using the magna-mike with measurements taken at 0.25” increments up the container wall, as shown in Figure 11, as well as measurements in the heel. These measurements were taken at the parting line by the bottom detent at 12:00 as shown in Figure 12 and then repeated every 90 degrees around the container for a total of 64 measurements. Figure 11. Magna-Mike Measurement Locations 27
Page 1 and 2: EFFECTS OF EXTRUSION BLOW MOLDING I
Page 3 and 4: Copyright by Kirk Alan Valko 2004
Page 5 and 6: TABLE OF CONTENTS LIST OF TABLES ..
Page 7 and 8: LIST OF TABLES Table 1. Fasti Cost
Page 9 and 10: Figure 24. Assembly Drawing........
Page 11 and 12: 1 - INTRODUCTION AND LITERATURE REV
Page 13 and 14: The process of extrusion blow moldi
Page 15 and 16: and dropped onto the conveyor, the
Page 17 and 18: Internal cooling is the process of
Page 19 and 20: pin is entering the bottle finish.
Page 21 and 22: 1.3.3 Costs Total cost of the unit
Page 23 and 24: Figure 7. Machine Surround Before F
Page 25 and 26: Table 2. Effect of Decreased Crysta
Page 27 and 28: 1.4.2 Wall thickness In addition to
Page 29 and 30: 2 - EXPERIMENTAL DESIGN AND TEST ME
Page 31 and 32: to determine the connection between
Page 33 and 34: 2.2 Experimental Methods 2.2.1 Samp
Page 35: Average temperature, checked by the
Page 39 and 40: D 2659, 1995). Twenty samples from
Page 41 and 42: Figure 15. Compression Data Example
Page 43 and 44: Figure 16. DSC Sample Pan Crimper T
Page 45 and 46: 3 - DATA AND RESULTS 3.1 Cycle time
Page 47 and 48: Table 7. Dimensional Test Result Co
Page 49 and 50: 3.3 Compression Strength Compressio
Page 51 and 52: Table 10. Percent Crystallinity of
Page 53 and 54: Table 12. Percent Crystallinity at
Page 55 and 56: wall thickness. Compression strengt
Page 57 and 58: performance tests. It would be desi
Page 59 and 60: 5.8 Optical Microscopy Optical micr
Page 61 and 62: 51 APPENDIX A Dimensional Results T
Page 63 and 64: 53 Table 15. Dimensional Test Resul
Page 65 and 66: Figure 18. Conventional Wall Thickn
Page 67 and 68: Figure 22. Fasti Wall Thickness 2 0
Page 69 and 70: Table 18. Compression Test Results
Page 71 and 72: Bekum Blow Molder Operating Instruc
Page 73 and 74: a) “SP1”(set point one) tempera
Page 75 and 76: i) Only one function may be used at
Page 77 and 78: ) Use Screwdriver to turn catch abo
Page 79 and 80: Figure 25. Detail 01 - Adaptor 69
Page 81 and 82: Figure 27. Detail 03 - Cooling Slee
Page 83 and 84: Figure 29. Detail 05 - Tip 73
Page 85 and 86: APPENDIX E Fasti Setup Experiment E
Page 87 and 88:
Data Analysis Figures 31, 32, and 3
Page 89 and 90:
Figure 31. Main Effects Plot for Fa
Page 91 and 92:
BIBLIOGRAPHY ASTM Standard D2463-95
show all

EFFECTS OF EXTRUSION BLOW MOLDING INTERNAL COOLING ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?