EFFECTS OF EXTRUSION BLOW MOLDING INTERNAL COOLING ...

More documents

Recommendations

Info

APPENDIX D Blow Pin Drawings Figure 24. Assembly Drawing 68
Figure 25. Detail 01 – Adaptor 69
Page 1 and 2:
EFFECTS OF EXTRUSION BLOW MOLDING I
Page 3 and 4:
Copyright by Kirk Alan Valko 2004
Page 5 and 6:
TABLE OF CONTENTS LIST OF TABLES ..
Page 7 and 8:
LIST OF TABLES Table 1. Fasti Cost
Page 9 and 10:
Figure 24. Assembly Drawing........
Page 11 and 12:
1 - INTRODUCTION AND LITERATURE REV
Page 13 and 14:
The process of extrusion blow moldi
Page 15 and 16:
and dropped onto the conveyor, the
Page 17 and 18:
Internal cooling is the process of
Page 19 and 20:
pin is entering the bottle finish.
Page 21 and 22:
1.3.3 Costs Total cost of the unit
Page 23 and 24:
Figure 7. Machine Surround Before F
Page 25 and 26:
Table 2. Effect of Decreased Crysta
Page 27 and 28: 1.4.2 Wall thickness In addition to
Page 29 and 30: 2 - EXPERIMENTAL DESIGN AND TEST ME
Page 31 and 32: to determine the connection between
Page 33 and 34: 2.2 Experimental Methods 2.2.1 Samp
Page 35 and 36: Average temperature, checked by the
Page 37 and 38: Table 5. Bottle Body Dimension Tole
Page 39 and 40: D 2659, 1995). Twenty samples from
Page 41 and 42: Figure 15. Compression Data Example
Page 43 and 44: Figure 16. DSC Sample Pan Crimper T
Page 45 and 46: 3 - DATA AND RESULTS 3.1 Cycle time
Page 47 and 48: Table 7. Dimensional Test Result Co
Page 49 and 50: 3.3 Compression Strength Compressio
Page 51 and 52: Table 10. Percent Crystallinity of
Page 53 and 54: Table 12. Percent Crystallinity at
Page 55 and 56: wall thickness. Compression strengt
Page 57 and 58: performance tests. It would be desi
Page 59 and 60: 5.8 Optical Microscopy Optical micr
Page 61 and 62: 51 APPENDIX A Dimensional Results T
Page 63 and 64: 53 Table 15. Dimensional Test Resul
Page 65 and 66: Figure 18. Conventional Wall Thickn
Page 67 and 68: Figure 22. Fasti Wall Thickness 2 0
Page 69 and 70: Table 18. Compression Test Results
Page 71 and 72: Bekum Blow Molder Operating Instruc
Page 73 and 74: a) “SP1”(set point one) tempera
Page 75 and 76: i) Only one function may be used at
Page 77: ) Use Screwdriver to turn catch abo
Page 81 and 82: Figure 27. Detail 03 - Cooling Slee
Page 83 and 84: Figure 29. Detail 05 - Tip 73
Page 85 and 86: APPENDIX E Fasti Setup Experiment E
Page 87 and 88: Data Analysis Figures 31, 32, and 3
Page 89 and 90: Figure 31. Main Effects Plot for Fa
Page 91 and 92: BIBLIOGRAPHY ASTM Standard D2463-95
show all

EFFECTS OF EXTRUSION BLOW MOLDING INTERNAL COOLING ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?