Section 6: Selected Applications & Techniques

More documents

Recommendations

Info

Pipe Scanning- Contact Methods
Q: Calculate the maximum shear wave angle and the range for 360° revolution scanning when the shear wave angle is 45°. Given that the OD=6” Thickness=3/4” Answer: (a) The maximum shear wave angle ϴ = Sin -1 (ID/OD) = Sin -1 (2.25/3) ϴ = 48.6° Max. (b) ?
Page 1:
Section 6: Selected Applications &
Page 5 and 6:
6.11: Casting 6.12: Inspection of b
Page 7 and 8:
6.1.1 Casting Defects & Discontinui
Page 9 and 10:
Casting Defects & Discontinuities-
Page 11 and 12:
Casting Defects & Discontinuities
Page 13 and 14:
Casting Defects & Discontinuities
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Processing Defects & Discontinuitie
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39:
6.1.3 Welding Defects & Discontinui
Page 42 and 43:
Welding Defects & Discontinuities
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Welding Defects & Discontinuities-
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Service Induced Defects & Discontin
Page 62 and 63:
Figure 4-24 - In a carbon steel sam
Page 64 and 65:
Figure 4-36 - Weld detail used to j
Page 66 and 67:
Figure 4-38 - Failure of DMW joinin
Page 68 and 69:
Figure 4-58 - Cross-sectional view
Page 70 and 71:
Figure 5-2 - Hot Lean Amine Corrosi
Page 72 and 73:
Figure 5-46 - Overhead interstage k
Page 74 and 75:
Figure 5-48 - Metallographic sample
Page 76 and 77:
6.2: Rail Inspection
Page 78 and 79: The need for a better inspection me
Page 80 and 81: Transverse Fissure
Page 82 and 83: One of the methods used to inspect
Page 84 and 85: Techniques: Examples of axles with
Page 86 and 87: 6.3: Weldments (Welded Joints)
Page 88 and 89: UT of Weldments (Welded Joints) F s
Page 90 and 91: Flaw Detection- Depth Determination
Page 92 and 93: T = Plate Thickness ϴ = Shear wave
Page 94 and 95: Flaw Detection- Triangulations of r
Page 96: To determine the proper scanning ar
Page 99 and 100: Expert at works
Page 101 and 102: Typically scanning patterns
Page 103 and 104: Weld Scanning
Page 105 and 106: Weld Scanning
Page 107 and 108: Echo Dynamic- Position of Defects
Page 109 and 110: Plate Weld Scanning
Page 111 and 112: Plate Weld Scanning
Page 113 and 114: Practice Makes Perfect 52. One of t
Page 115 and 116: 6.4: Pipe & Tube
Page 117 and 118: Pipe & Tube
Page 119 and 120: Pipe Scanning
Page 121 and 122: Pipe Scanning 48.59 o max 30 o max
Page 123 and 124: Pipe Scanning
Page 125 and 126: Pipe Scanning- thickness/OD ratio W
Page 127: Pipe Scanning- Contact Methods
Page 131 and 132: Q35: During immersion testing of pi
Page 133 and 134: 6.5: Echo Dynamic
Page 135 and 136: 6.5.1 Basic echodynamic pattern of
Page 137 and 138: C.1 Pattern 1 Point-like reflector
Page 139 and 140: C.2 Pattern 2 Extended (elongated)
Page 145 and 146: C.3 Pattern 3a Extended (elongated)
Page 147 and 148: C.3 Pattern 3b Oblique incidence, t
Page 149 and 150: C.3 Pattern 3b Oblique incidence, t
Page 151 and 152: C.4 Pattern 4 Multiple reflector re
Page 153 and 154: Echodynamic- Change of echo height
Page 155 and 156: Break Time
Page 157 and 158: Echo Dynamic of Discontinuity- Flaw
Page 159 and 160: Echo Dynamic of Discontinuity- Impr
Page 161 and 162: Echo Dynamic of Discontinuity- Refl
Page 167 and 168: Echo Dynamic of Discontinuity- Tand
Page 169 and 170: Echo Dynamic of Discontinuity- Tand
Page 171 and 172: Echo Dynamic- Root Concavity
Page 173 and 174: Echo Dynamic
Page 175 and 176: Echo Dynamic
Page 177 and 178: Echo Dynamic- Broad indication with
Page 179 and 180:
Echo Dynamic
Page 181 and 182:
Echo Dynamic The echo response from
Page 183 and 184:
Echo Dynamic Typical Echo Dynamic P
Page 185 and 186:
Echo Dynamic Typical Echo Dynamic P
Page 187 and 188:
Q183. In immersion testing, irrelev
Page 189 and 190:
Q46. Which best describes a typical
Page 191 and 192:
6.6: Technique Sheets
Page 193 and 194:
Hanger Pin Testing using Shear Wave
Page 195 and 196:
Physical Dimension
Page 197 and 198:
Physical Dimension
Page 199 and 200:
Reporting: Scanning Report - Top of
Page 201 and 202:
Mock-Up
Page 203 and 204:
Mock-Up
Page 205 and 206:
Mock-Up
Page 207 and 208:
Hanger Pin Testing using Shear Wave
Page 209 and 210:
Pitch and Catch Methods- Set-up
Page 211 and 212:
6.7: Material Properties- Elastic M
Page 213 and 214:
6.7.2 The attenuation method The at
Page 215 and 216:
6.7.3 Velocity Measurements Velocit
Page 217 and 218:
Elastic Modulus Measurement - Young
Page 219 and 220:
These basic material properties, wh
Page 221 and 222:
Equipment: The velocity measurement
Page 223 and 224:
Testing Procedure: Equipment Used.
Page 225 and 226:
Velocity & Equations Poisson Ratio
Page 227 and 228:
6.8: High Temperature Ultrasonic Te
Page 229 and 230:
1.0 Background: Although most ultra
Page 231 and 232:
Temperature Limitation: Conventiona
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
敦煌大漠美食 -50 度火
Page 239 and 240:
2.0 Methods used for H.Temperature
Page 241 and 242:
For precision thickness gauging app
Page 243 and 244:
(1b) Flaw detection As in high temp
Page 245 and 246:
2.2 High Temperature Couplants Most
Page 247 and 248:
Keyword: Note that normal incidence
Page 249 and 250:
As a general rule, if the outer cas
Page 251 and 252:
2.4 Equipment Functions Freeze Func
Page 253 and 254:
Keyword: ■ ■ Velocity change of
Page 255 and 256:
3.3 Increased Attenuation: Sound at
Page 257 and 258:
3.4 Angular Variation in Wedges: Wi
Page 259:
6.9: Dimension-Measurement Applicat
Page 263 and 264:
6.9.2 Thickness measurements are ma
Page 265 and 266:
6.9.3 Position measurements Positio
Page 267 and 268:
Fig. 60 Method of determining corre
Page 269 and 270:
Fig. 61 Setup for determining the p
Page 271 and 272:
6.10: In-Service Inspection
Page 273 and 274:
In-Service Inspection- Testing for
Page 275 and 276:
In-Service Inspection- (a) Crack te
Page 277 and 278:
In-Service Inspection- (a) Testing
Page 279 and 280:
6.11: Casting
Page 281 and 282:
Casting- Typical casting defects an
Page 283 and 284:
Casting- Detection of shrinkage cav
Page 285 and 286:
Inspection of Bonded Joints If the
Page 287 and 288:
6.13: Corrosion Monitoring
Page 289 and 290:
Despite these drawbacks, ultrasonic
Page 291 and 292:
Crack Monitoring Laboratory and in-
Page 293 and 294:
The use of pulse-echo techniques fo
Page 295 and 296:
6.15: Stress Measurements
Page 297 and 298:
The real limitation of this techniq
Page 299 and 300:
The real limitation of
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
6.App-1: TOFD Introduction NOTE: No
Page 307 and 308:
TOFD provides a wide area of covera
Page 309 and 310:
TOFD offers rapid weld inspection w
Page 311 and 312:
Due to the low amplitude of the dif
Page 313 and 314:
Tips Diffractions
Page 315 and 316:
TOFD
Page 317 and 318:
TOFD has been used for some time fo
Page 319 and 320:
Figure 5-2 - Hot Lean Amine Corrosi
Page 321 and 322:
For these types of weld inspections
Page 323 and 324:
Scan of weld with cursor positioned
Page 325 and 326:
Measurement of good area shows thic
Page 327 and 328:
6.11.3.3TOFD for Corrosion Measurem
Page 329 and 330:
TOFD for Weld- TOFD Parallel Scanni
Page 331 and 332:
■ Perpendicular Scanning Scanning
Page 333 and 334:
Typical “Perpendicular” Weld Sc
Page 335 and 336:
■ Benefit of TOFD Parallel Scanni
Page 337 and 338:
The Experts at work.
Page 339 and 340:
Break Time mms://a588.l3944020587.c
Page 341 and 342:
Break Time
show all

Section 6: Selected Applications & Techniques

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?