Snap-Action Switches Detection Switches General Catalogue 2005

ABC2
DIMENSIONS
1. Standard type
(Right angle type with positioning boss)
mm inch General tolerance: ±0.15 ±.006
Recommended PC board pattern
1.2
.047
+0.1
0.05–0.15
+.004
.002–.006
1.5 ±0.05
.059 ±.002
Upper direction
0.3
.012
Operation direction
+0.05
1.40–0.1
+.002
.055–.004
0.60
.024
+0.05
2- φ0.80
2- φ.031
0 hole
+.002
0 hole
1.0
.039
5.9
.232
+0.3
FP=2.7–0.1
+.012
.106–.004
OP=2.3 ±0.3
.091 ±.012
TTP=1.3 ±0.1
.051 ±.004
R 2.55
R .100
Side direction
0.6
.024
0.4
.016
0.8
.031
2.1 ±0.1
.083 ±.004
3.4
.134
±0.04
φ 0.7
±.002
φ .028
±0.04
φ 0.7
±.002
φ .028
1.5 ±0.1
.059 ±.004
Reference point
3.5 ±0.08
.138 ±.003
5.1
.201
2-C0.7
2-C.028
+0.1
0.4–0.05
+.004
.016–.002
2-C0.10
2-C.004
(Right angle type without positioning boss)
+0.1
0.05–0.15
+.004
.002–.006
Recommended PC board pattern
R 2.55
R .100
Upper direction
0.3
.012
Operation direction
Side direction
0.6
.024 0.4
.016
+0.05
1.40–0.1
+.002
.055–.004
0.60
.024
1.0
.039
5.9
.232
1.2
.047
+0.3
FP=4.8–0.1
+.012
.189–.004
OP=4.4 ±0.3
.173 ±.012
TTP=3.4 ±0.1
.134 ±.004
0.8
.031
2.1 ±0.1
.083 ±.004
3.4
.134
Reference point
3.5 ±0.08
.138 ±.003
5.1
.201
2-C0.7
2-C.028
(Left angle type with positioning boss)
Recommended PC board pattern
1.2
.047
+0.1
0.05–0.15
+.004
.002–.006
Operation direction
0.8
.031
3.4
.134
2.1 ±0.1
.083 ±.004
Side direction
0.4 0.6
.016 .024
4.1
.161
Upper direction
0.3
.012
R 2.55
R .100
TTP=1.3 ±0.1
.051 ±.004 OP=2.3 ±0.3
+0.3
FP=2.7–0.1
.091 ±.012 +.012
.106–.004
+0.05
1.40–0.1
+.002
.055–.004
0.60
.024
±0.04
φ 0.7
±.002
φ .028
±0.04
φ 0.7
±.002
φ .028
1.5 ±0.1
.059 ±.004
+0.05
2- φ0.80
2- φ.031
0 hole
+.002
0 hole
1.0
.039
5.9
.232
1.5 ±0.05
.059 ±.002
Reference point
3.5 ±0.08
.138 ±.003
5.1
.201
2-C0.7
2-C.028
+0.1
0.4–0.05
+.004
.016–.002
2-C0.10
2-C.004
132