Snap-Action Switches Detection Switches General Catalogue 2005

More documents

Recommendations

Info

HIGH CONTACT CAPACITY, PRECISE OPERATION FEATURES • 15 A High current switching capacity and high precision • Wide allowance of operating speed • Versatile variety of actuators • UL/CSA approved NZ BASIC (AM1) SWITCHES AM1 TYPICAL APPLICATION • <strong>General</strong> industrial machinery • Medical equipment • Measuring instruments • Transportation equipment • Home electric appliances ORDERING INFORMATION Ex. AM 1 5 0 1 K Type of switch NZ basic (AM1) switch Upper body cover shape & terminal 1: Flat, solder terminal 3: Flat, screw terminal 5: Grooved, solder terminal 7: Grooved, screw terminal Upper body cover shape Flat Grooved Basic specifications 0: Standard type 1: Oil tight type 3: Reversed action type 4: One way type Remarks: Not every combination is available. Please refer to the following table, “PRODUCT TYPES”. Actuators 0: Pin plunger 1: Hinge lever (leaf spring) 3: Hinge roller lever (roller, leaf, spring) 4: Hinge short roller lever 5: Overtravel plunger 6: Compact overtravel plunger 7: Panel mount plunger 811: Panel mount roller plunger 812: Panel mount cross roller plunger TERMINAL VARIATION Standard types, reversed action types and oil tight types are available in two terminal designs, solder and screw terminals, as shown in the above columns: Differences in dimension between solder and screw terminals are as follows; mm inch Solder terminal Screw terminal 6.3 .248 9.1 .358 49.2 1.937 49.2 1.937 N.O. CIRCUT N.C. CIRCUT 17.5 .689 C NO NC 17.5 .689 Terminal plate 19.8 .780 M4 screw P0.7 20.2 .795 51
AM1 PRODUCT TYPES 1. Standard type Actuator Solder terminal Screw terminal Pin plunger AM1100K AM1300K Over travel plunger AM1105K AM1305K Compact over travel plunger AM1106K AM1306K Panel mount plunger AM1107K AM1307K Panel mount roller plunger AM110811K AM130811K Panel mount cross roller plunger AM110812K AM130812K Flexible leaf lever AM1101K AM1301K Flexible roller leaf lever AM1103K AM1303K Rigid lever AM1501K AM1701K Rigid short roller lever AM1504K AM1704K Rigid roller lever AM1503K AM1703K One way type•Rigid short roller lever AM1544K AM1744K One way type•Rigid roller lever AM1543K AM1743K Reversed action type•Rigid lever AM1531K AM1731K Reversed action type •Rigid short roller lever AM1534K AM1734K Reversed action type•Rigid roller lever AM1533K AM1733K 2. Oil tight types Actuator Solder terminal Screw terminal Rigid lever AM1511K AM1711K Rigid short roller lever AM1514K AM1714K Rigid roller lever AM1513K AM1713K Remarks: 1. Standard part number indicates UL/CSA mark. 2. Standard packing for inner carton: 20cps. SPECIFICATIONS 1. Contact Rating Type Standard types One way types Reversed action types Oil tight types Voltage Resistive load Inductive load Motor or lamp load (cos φ = 1) (cos φ = 0.6 to 0.7) N.C. N.O. 125 V AC 15 A 10 A 4 A 2 A 250 V AC 15 A 10 A 3 A 1.5 A 480 V AC 3 A 2 A 1.5 A 0.75 A 125 V DC 0.5 A 0.05 A — — 250 V DC 0.25 A 0.03 A — — 125 V AC 15 A 10 A 3 A 1.5 A 250 V AC 10 A 6 A 2 A 1.0 A 125 V DC 0.5 A 0.05 A — — 2. Characteristics Expected life Mechanical Electrical (O.T.: Max.) Item Pin plunger types (O.T.: specified value) Other types (O.T.: specified value) Insulation resistance Between open terminals Dielectric Between each terminal and other exposed metal parts strength Between each terminal and ground Contact resistance (initial) (by voltage drop, 1 A, 6–8 V DC) Vibration resistance (Pin plunger type) Shock Pin plunger types resistance Other types Allowable operating speed (at no load) Max. operating cycle rate (at no load) Ambient temperature Weight Specifications Min. 2 ×10 7 (60 cpm) (at rated overtravel) (Oil tight: Min. 1.5 ×10 6 ) Min. 5 ×10 6 (60 cpm) (at rated overtravel) (Oil tight: Min. 1.5 ×10 6 ) Min. 5 ×10 5 (20 cpm) (at rated load) (Oil tight: Min. 1.5 ×10 5 ) Min. 100 MΩ(at 500 V DC) 1,000 Vrms for 1 min. 2,000 Vrms for 1 min. 2,000 Vrms for 1 min. Max. 50 mΩ Single amplitude: 0.75 mm, 10 to 55 Hz (contact opening: max. 1 msec.) Min. 300 m/s 2 (contact opening: max. 1 msec.) Min. 50 m/s 2 (contact opening: max. 1 msec.) 0.1 to 1,000 mm/sec. (at pin plunger position) 240 cpm –25°C to +80°C –13°F to +176°F (no freezing at low temperature) Approx. 20 to 55 g.705 to 1.940 oz 52
Page 1 and 2: Snap-Action Switches ■ Detection
Page 3 and 4: Matsushita Electric Works Switch Se
Page 5 and 6: Switch Selector Chart • Type of s
Page 7 and 8: Switch Selector Chart FS/FS-T Submi
Page 9 and 10: Switch Selector Chart Detection Swi
Page 11 and 12: TECHNICAL TERMINOLOGY & CAUTIONS FO
Page 13 and 14: TECHNICAL TERMINOLOGY & CAUTIONS FO
Page 15 and 16: TURQUOISE SWITCHES TURQUOISE SWITCH
Page 17 and 18: NOTES FOR TURQUOISE SWITCHES 7. Was
Page 19 and 20: ASQ1 OPERATION CONCEPT DIAGRAM (ref
Page 21 and 22: ASQ1 DIMENSIONS mm inch General tol
Page 23 and 24: ASQ1 2. Wire leads bottom type: Mou
Page 25 and 26: ASQ1 7. Environment • Although co
Page 27 and 28: ABJ1,2,3,4,5 PRODUCT TYPES 1. Dust
Page 29 and 30: ABJ1,2,3,4,5 Gold-clad Leaf lever M
Page 31 and 32: ABJ1,2,3,4,5 DIMENSIONS mm inch Gen
Page 33 and 34: ABJ1,2,3,4,5 Leaf lever mm inch Gen
Page 35 and 36: ABJ1,2,3,4,5 Mounting hole 3mm .118
Page 37 and 38: ABS1,4,5 PRODUCT TYPES 1. Dust prot
Page 39 and 40: ABS1,4,5 3. Immersion protected typ
Page 41 and 42: ABS1,4,5 5. Immersion protected typ
Page 43 and 44: ABS1,4,5 DIMENSIONS mm inch General
Page 45 and 46: ABS1,4,5 Right angle type mm inch G
Page 47 and 48: ABV1 HIGH ENVIRONMENTAL RESISTANCE
Page 49 and 50: ABV1 Gold-clad Contact Gold-clad Ac
Page 51: ABV1 Hinge lever mm inch General to
Page 55 and 56: AM1 DIMENSIONS mm inch General tole
Page 57 and 58: AM1 Rigid lever mm inch General tol
Page 59 and 60: AM1 4. Oil tight types mm inch Gene
Page 61 and 62: AM5 VDE MINIATURE SWITCHES WITH HIG
Page 63 and 64: AM5 2) Side COM terminal Pin plunge
Page 69 and 70: AM5 2. Characteristics Type 21A typ
Page 71 and 72: AM5 Side COM terminal mm inch Gener
Page 73 and 74: AM5 6. Short roller lever mm inch G
Page 75 and 76: AH7 HIGH PERFORMANCE MINIATURE SWIT
Page 77 and 78: AH7 SPECIFICATIONS 1. Contact ratin
Page 79 and 80: AH7 Side COM terminal (with right-h
Page 81 and 82: AV3,AVM3/AVT3,AVL3 NEW SUBMINIATURE
Page 83 and 84: AV3,AVM3/AVT3,AVL3 PRODUCT TYPES 1.
Page 85 and 86: AV3,AVM3/AVT3,AVL3 3.FS switches (I
Page 87 and 88: AV3,AVM3/AVT3,AVL3 3) Hinge lever 4
Page 89 and 90: AV3,AVM3/AVT3,AVL3 1-(2) Self-stand
Page 91 and 92: AV3,AVM3/AVT3,AVL3 2-(2) Self-stand
Page 93 and 94: AV3G SUBMINIATURE SWITCHES (Contact
Page 95 and 96: AVM3P HIGH CAPACITY, LONG LIFE SUBM
Page 97 and 98: AVM3P Short hinge lever mm inch Gen
Page 99 and 100: AVM3P NOTES 1. Fastening of the swi
Page 101 and 102: AV6 PRODUCT TYPES 1. Lever position
Page 103 and 104:
AV6 3. Simulated roller lever Lever
Page 105 and 106:
AH1 ULTRA-MINIATURE SWITCHES WITH H
Page 107 and 108:
AH1 3. Operating characteristics 1)
Page 109 and 110:
AH1 3. PC board terminal (Right/Lef
Page 111 and 112:
AV4 PRODUCT TYPES Type of contacts
Page 113 and 114:
AV4 2. Angle terminal Right angle t
Page 115 and 116:
AGX VDE SAFETY INTERLOCK SWITCH SMA
Page 117 and 118:
AGX CONSTRUCTION Dual safety constr
Page 119 and 120:
AV1 VDE SAFETY INTERLOCK SWITCH CON
Page 121 and 122:
AV1 CONSTRUCTION [Screw mounting ty
Page 123 and 124:
AV1 3 Form A 3 Form A type without
Page 125 and 126:
AGL 3. Operating characteristics Pi
Page 127 and 128:
ABC3 1.4 MM ULTRA SLIM HIGH RELIABL
Page 129 and 130:
ABC3 CIRCUIT CONSTRUCTION • N.O.
Page 131 and 132:
ABC2 NEW 1 Form A 1 Form B (Additio
Page 133 and 134:
ABC2 DIMENSIONS 1. Standard type (R
Page 135 and 136:
ABC2 2. Long stroke type (Right ang
Page 137 and 138:
ABC2 NOTES 1. Mounting 1) The posit
Page 139 and 140:
ABC1 SPECIFICATIONS 1. Contact rati
Page 141 and 142:
ABP8 A PIERCED EARRING SIZE DETECTI
Page 143 and 144:
ABU8 A ULTRA MINIATURE SIZED DETECT
Page 145 and 146:
AHF2 SMALL, HIGHLY RELIABLE TIP SEN
Page 147 and 148:
AHF2 • Reverse mounting type mm i
Page 149 and 150:
Standards Chart FS•FS-T switches
show all

Snap-Action Switches Detection Switches General Catalogue 2005

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?