Download Catalogue (PDF - 38.2mb) - Carba-Tec

HANDSCREW
CLAMPS
Classic cabinet
makers bench
clamps with
wooden jaws
that won’t mark
your work or
slip.
Order no. Description Price
HSC-4 50mm Throat $11.00
HSC-6 75mm Throat $15.00
HSC-8 115mm Throat $19.00
HSC-10 135mm Throat $20.00
GROZ
150MM
CLAMP
ON VISE
A useful, lightweight
vise for the young
woodworker or
home handyman.
The design allows for two clamping
options. Permanent clamping on the workbench
is available via bolt slots in the vise
base or via the 55mm integrated clamp.
Opening capacity: 120mm. 3.3kg.
Order no.
Price
GZ-39006 $51.00
Clamping, Vices & Benches
TWO WAY CROSS SLIDE VISE
Secures workpiece firmly and accurately on
the drill press table. Positive positioning in
two coordinates, lets you move the piece
accurately. These controls provide precise
adjustment for a myriad of drilling and cutting.
Jaw width 103mm, Jaw opens 95mm.
Weight: 10kg.
Order no.
Price
CSV-4 $88.00
KREG ® KLAMP VISE
The Klamp Vise can be connected to
almost any workbench providing over 158kg
of clamping power. Vertical clamping, sideways
clamping, vise-style clamping, routing,
sanding, sawing, and a whole lot more.
Order no.
Price
KR-KKS1060 $85.00
GROZ QUALITY G CLAMPS
Order no. Cap. Weight Price
GZ-35802 150mm 1.25kg $18.00
GZ-35803 200mm 1.5kg $27.00
THREE-WAY
EDGING CLAMP
Capacity 65mm,
load 32kg. For
gluing edge
banding etc. Weight
950g. Sold as pair.
Order no.
Price
JEC-65 $18.00
GROZ PLAIN SCREW
WOODWORKING VISE
Manufactured from close-grained grey cast
iron for long years of service. Accurately machined
housing assure smooth sliding movement.
Solid steel guide rods reduce wear
and tear giving the vises a smooth and true
parallel action, free of side or cross deflection.
Jaw width is 175mm. 200mm capacity.
Order no.
Price
GZ-39001 $88.00
GROZ QUICK
RELEASE VISES
Simply pressing the trigger
initiates the quick action,
with the front jaw sliding
freely. Releasing
the trigger returns the
mechanism to normal for fine adjustment.
A very useful feature in repetitive work situations.
Jaw opening capacity for 175mm vise
is 200mm and 250mm for the 225mm vise.
Order no. Description Price
GZ-39007 175mm $110.00
GZ-39009 225mm $176.00
PARROT VISE
Built like a machinist’s vise, the Parrot vise incorporates
a unique tightening cam that lets
it pivot freely through 360° until you tighten
the jaws firmly, locking the vise in place. This
allows you to back off the clamp screw just
enough to rotate the vise for access to any
part of a work piece without releasing it from
the jaws. 89mm wide cast iron jaws open to
120mm. There is a 44mm square machined
anvil just behind the jaws. 4kg.
Order no.
Price
PARROT-VISE $143.00
BENCH STOP
Mounts flush with bench surface. Simply turn
a screw and the jaw raises and locks in position.
Ideal for planing and sanding. 80g.
Order no.
Price
MJ-815 $16.00
LARGE
FRONT
VISE
10-1/2” x 21” overall with
a 1-1/8” diameter screw,
and 13” clamping capacity less front jaw
thickness. It can be added to an existing
bench or built into an new one.
Order no.
Price
CTV-2038 $83.00
MACHINIST-STYLE CLAMPS
Using the same principles as a woodworking
handscrew, these steel clamps are ideal
for clamping small assemblies. The 1-1/2”
long jaws have a 1” opening capacity. The
clamps are most commonly used for finicky
problems such as holding wire assemblies
for soldering or for repairing a veneer chip in
a table apron.
Order no.
Price
09A01-94 $13.00
Want to see more? See our website for our full range of products.
89