Roof and Wall - Lane Roofing

More documents

Recommendations

Info

Lining Trays & Special Roof Profiles Structural lining trays Corus Panels and Profiles can offer a structural lining tray that is suitable for both roof and wall cladding applications spanning across the main steels and omitting the need for HL600/130 purlins or cladding rails. Load/span figures 38.50 60 130 These figures are based on a maximum load of 1.50kN/m 2 and a deflection limit of L/200. HL600/130 Perf (36%) Cover width 600 Material Gauge (mm) Weight (kg/m 2 ) Load/Span – max span (mm) SS Load/Span – max span (mm) DS Working platform HL600/130 S 1.00 13.08 6000 6000 Y HL600/130 S 0.75 9.81 5000 5000 N Perf (36%) Special roof profiles In order to offer the specifier more choice, it is possible to produce some of our more specialist sections adapted to suit roof cladding applications. The necessary modifications render these profiles ‘special’ and therefore may be subject to a minimum order requirement and extended lead times. R19 1000/19 Protile R100 Cover width 1066.8 152.4 25 95.4 57 Cover width 1000 15-20 106 106 250 144 19 Cover width 700 233.3 63 100 19 19 For further information please contact our Sales Department. Load/span figures These tables are based on a total ‘dead’ and ‘super imposed’ load of 1.20 kN/m 2 and a deflection limit of L/200. The quoted spans are more onerous than the profiles maximum allowable spans when subjected to wind suction loads. Therefore, the tables can be used as a conservative guide for loading in either direction. For differing conditions please consult our full load tables and/or consult our Technical Services Department. Gauges The data held within this table concerns itself with the minimum recommended gauges. Different gauges, colours, coatings etc. can be made available subject to special order. 109 37 See page 4 for standard roof profiles. Full design and installation guide available 10 Roof & Wall - Site Assembled Systems
Lining Trays & Special Roof Profiles Material Gauge (mm) Weight (kg/m 2 ) Load/Span – max span (mm) SS Load/Span – max span (mm) MS Minimum self curve (m) Minimum factory curve (mm) Minimum roof pitch R19 S 0.7 6.43 1300 1700 20 (h), 30 (p), 35 (mp) 400 10 A 0.9 2.89 1000 1300 20 (sa/ca), 25 (ma) 400 10 1000/19 Protile S 0.7 5.89 666 666 † NA 10 R100 S 0.7 9.80 5200 5600 110 (h), 120 (p), 125 (mp) NA 4 A 0.9 4.41 3800 4600 110 (sa/ca), 115 (ma) NA 4 Key S – Steel A – Aluminium h – HPS200 ® by Corus p – Colorcoat ® PVDF mp – Metallic PVDF/Celestia ® by Corus sa – Stucco embossed aluminium ca – Coated aluminium ma – Metallic coated aluminium SS – Single span MS – Multi span DS – Double span † – Contact technical department Before ordering it is important to confirm with Corus Panels and Profiles which side of the profile carries the main surface finish. All profiles comply to current MCRMA Tolerances. Above: Winchester House School, Sports Hall, Winchester. Right: Zenith, Basildon. Roof & Wall - Site Assembled Systems 11
Page 1 and 2: Corus Panels and Profiles Roof and
Page 3 and 4: Introduction Corus Panels and Profi
Page 5 and 6: Standard Roof Profile Range Materia
Page 7 and 8: Standard Wall Profile Range Materia
Page 9: Standard Lining Profiles Range Mate
Page 13 and 14: Special Wall Profiles Left: The Eni
Page 15 and 16: Pressed Profiles Pressed profiles,
Page 17 and 18: Introduction Firewall System Select
Page 19 and 20: 4 Hour 15 minutes Insulation 4 Hour
Page 21 and 22: 4 Hour 30 minutes Insulation 4 Hour
Page 23 and 24: 4 Hour 15 Minutes Insulation 4 Hour
Page 25 and 26: 4 Hour 15 Minutes Insulation 4 Hour
Page 27 and 28: Building Regulations Firewall Build
Page 29 and 30: Acoustics Acoustic Systems Acoustic
Page 31 and 32: Acoustic Systems Sound Reduction In
Page 33 and 34: Acoustic Systems Sound Reduction an
Page 35 and 36: Acoustic Systems Sound Reduction St

Roof and Wall - Lane Roofing

Create successful ePaper yourself

Delete template?

Save as template?