Roof and Wall - Lane Roofing

More documents

Recommendations

Info

Standard Lining Profiles Range Standard lining profiles range Corus Panels and Profiles offer a range of lining panels specifically developed to be compatible with our outer sheet product range thus allowing the accommodation of modular rooflights. CL6/914 CL6/914 Perf (20%) 152.4 Cover width 914.4 25 57 95.4 19 Lengths Being roll formed, long lengths are available but for practical site handling purposes with the 0.40 mm gauge options we would suggest these are kept to a maximum of 5m. LP1000 LP1000 Perf (21.5%) 166.7 Cover width 1000 25 53.5 8 60 106.7 19 Vapour Barrier All non-perforated profiles provide a side lap which can be sealed to provide a vapour check. A correctly sealed lining panel will easily meet the 10m 3 /hr/m 2 @ 50 pascals air tightness requirement of the new building regulations. 1000/19 † 1000/19 † Perf (33%) C19 C19 Perf (20%) RL32/1000 RL32/1000 Perf (22%) 15-20 250 152.4 200 Cover width 1000 144 106 106 19 19 Cover width 1066.8 25 16 57 19 95.4 Cover width 1000 27 32 127.5 Spans In roofing conditions, the spanning capabilities of the lining panels are largely dependent upon their self-weight and the weight of the insulation they are required to support. In normal conditions with 0.40mm gauge liners double span capabilities of up to 2m can be achieved. However, at spans approaching maximum it may be necessary to mechanically fix side laps and/or reverse the normal side lap to minimise separation. The span for non fragility rating may be less than span shown in tables. Contact our Technical Department for fixing details to comply with ACR(M)001:2000. Fire Rating All non perforated lining sheets provide a fire rating of Class 1 to BS476: Part 7 and Class 0 in accordance with current Building Regulations. Due to the nature of pan perforating, some undulations may be evident in the final product. 60 o 6.3 mm 4.5mm diameter holes at 6.3mm triangular centre Pattern open area - 46% Curving Self curving can induce stress marking in the sheet. The figures shown have been chosen with aesthetics in mind and therefore minimise visible induced stress. Figures are also based on the profile being fitted above the purlin on a convex curved roof. Factory curved data relates to a single convex curve. Information regarding double or wave curves must be obtained from Corus Panels and Profiles. Full design and installation guide available 8 8 Secret Roof & Fix Wall Product - Site Selector Assembled Systems
Standard Lining Profiles Range Material Gauge (mm) Weight (kg/m 2 ) Load/Span – max span (mm) SS Load/Span – max span (mm) DS Minimum self curve (m) Minimum factory curve (mm) Working platform Compatible outer sheets if rooflights incorporated CL6/914 S 0.4 3.64 1600 2200 40 (le) 350 N R/C38A CL6/914 S 0.4 2.98 1300 1800 40 (le) 350 N R/C38A Perf (20%) LP1000 S 0.4 3.50 1600 2200 40 (le) 350 N R/C32/1000 LP1000 S 0.4 2.84 1300 1800 40 (le) 350 N R/C32/1000 Perf (21.5%) R40 1000/19 † S 0.7 5.89 2000 2000 40 (le) 250 N Clipfix 1000/19 † S 0.7 4.12 1800 1800 50 (le) 250 N Clipfix Perf (33%) A 0.9 2.70 1800 1800 40 (ca) 250 N Clipfix C19 S 0.7 6.33 2000 3000 20 (h), 30 (p/le), 35 (mp) 350 N R/C19 R/C38A – (profile pitch compatible) A 0.9 2.84 1600 2200 20 (sa/ca), 25 (ma) 350 N R/C19 R/C38A – (profile pitch compatible) C19 S 0.7 5.19 1700 2500 20 (h), 30 (p/le), 35 (mp) 350 N R/C19 Perf (20%) R/C38A – (profile pitch compatible) A 0.9 2.33 1300 1800 20 (sa/ca), 25 (ma) 350 N R/C19 R/C38A – (profile pitch compatible) RL32/1000 S 0.7 6.75 2500 3200 40 (h), 50 (p/le), 55 (mp) 400 Y* R/C32/1000 R40 A 0.9 3.03 2000 2600 40 (sa/ca), 45 (ma) 400 Y ‡ R/C32/1000 RL32/1000 S 0.7 6.75 2100 2700 40 (h), 50 (p/le), 55 (mp) 400 N R/C32/1000 Perf (22%) R40 A 0.9 2.43 1700 2200 40 (sa/ca), 45 (ma) 400 N R/C32/1000 R40 R40 R40 Key S – Steel A – Aluminium h – HPS200 ® by Corus p – Colorcoat ® PVDF mp – Metallic PVDF/Celestia ® by Corus sa – Stucco embossed aluminium ca – Coated aluminium ma – Metallic coated aluminium SS – Single span DS – Double span Before ordering it is important to confirm with Corus Panels and Profiles which side of the profile carries the main surface finish. All profiles comply to current MCRMA Tolerances. † Only available with Clipfix. * Maximum 2m centres suggested platform for ALU-SEAM ® roofs without lights ‡ Maximum 1.8m centres suggested platform for ALU-SEAM ® roofs without lights Finishes The data held within this table concerns itself with our standard product range. Non standard materials, gauges, colours and coatings are available to special order, subject to quantity required and extended lead time. Acoustics To meet the increasing demand for noise reduction in factories and public buildings Corus Panels and Profiles can supply lining panels with acoustic perforations incorporated in the flat pans of the profile. When correctly installed, these panels can provide a high level of acoustic absorbency instead of the reflective finish normally presented by plain metal sheeting. Whilst other patterns can be achieved the standard pattern is illustrated in the table opposite. Percentage open areas are highlighted next to the relevant profiles. See page 14 for special lining profiles. Space Decks Headquarters, Chard. Roof & Wall - Site Assembled Systems 9
Page 1 and 2: Corus Panels and Profiles Roof and
Page 3 and 4: Introduction Corus Panels and Profi
Page 5 and 6: Standard Roof Profile Range Materia
Page 7: Standard Wall Profile Range Materia
Page 11 and 12: Lining Trays & Special Roof Profile
Page 13 and 14: Special Wall Profiles Left: The Eni
Page 15 and 16: Pressed Profiles Pressed profiles,
Page 17 and 18: Introduction Firewall System Select
Page 19 and 20: 4 Hour 15 minutes Insulation 4 Hour
Page 21 and 22: 4 Hour 30 minutes Insulation 4 Hour
Page 23 and 24: 4 Hour 15 Minutes Insulation 4 Hour
Page 25 and 26: 4 Hour 15 Minutes Insulation 4 Hour
Page 27 and 28: Building Regulations Firewall Build
Page 29 and 30: Acoustics Acoustic Systems Acoustic
Page 31 and 32: Acoustic Systems Sound Reduction In
Page 33 and 34: Acoustic Systems Sound Reduction an
Page 35 and 36: Acoustic Systems Sound Reduction St

Roof and Wall - Lane Roofing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?