Roof and Wall - Lane Roofing

More documents

Recommendations

Info

Standard Roof Profile Range Standard roof profile range Corus Panels and Profiles offer an attractive and economic range of roof profiles to meet both the aesthetic and structural requirements of the designer. R13.5/3 Cover width 990.6 (Alternative 980) 19 R32/1000 Cover width 1000 27 76.2 (Alternative 75.38) 32 R35A Cover width 900 150 200 127.5 35 35 CLS Laundry, Newton Abbott. R38A R40 R46 R60 Clipfix 750 Seam–Loc ALU–SEAM ® 75 Cover width 914.4 38 19 152.4 82 Cover width 1000 31 40 242 333.3 Cover width 900 46 67 105 225 Cover width 800 60 64 200 90 Cover width 750 19.50 18.25 43.50 46 250 4 Cover width 410 48 205 Cover width 410 48 205 Load/span figures These tables are based on a total ‘dead’ and ‘super imposed’ load of 1.20 kN/m 2 and a deflection limit of L/200. The quoted spans are more onerous than the profiles maximum allowable spans when subjected to wind suction loads. Therefore, the tables can be used as a conservative guide for loading in either direction. For differing conditions please consult our full load tables and/or consult our Technical Services Department. Curving Self curving can induce stress marking in the sheet. The figures shown have been chosen with aesthetics in mind and therefore minimise visible induced stress. Self curved panel ends laps will ‘birdmouth’ slightly, therefore long sheet lengths are recommended to reduce the number of end laps. Factory curved data relates to a single convex curve. Information regarding double or wave curves must be obtained from Corus Panels and Profiles. Finishes The data held within this table concerns itself with our standard product range. Non standard materials, gauges, colours and coatings are available to special order, subject to quantity required and extended lead time. See page 10 for special roof profiles. Space Decks Headquarters, Chard. 4 Roof & Wall - Site Assembled Systems
Standard Roof Profile Range Material Gauge (mm) Weight (kg/m 2 ) Load/Span – max span (mm) SS Load/Span – max span (mm) MS Minimum self curve (m) Minimum factory curve (mm) Minimum Roof Pitch R13.5/3 S 0.7 6.81 1200 1500 20 (h), 30 (p), 35 (mp) 1000* 10 A 0.9 3.05 900 1200 20 (sa/ca), 25 (ma) 1000* 10 R32/1000 S 0.7 6.75 1900 2000 40 (h), 50 (p), 55 (mp) 400 4 A 0.9 3.02 1500 1800 40 (sa/ca), 45 (ma) 400 4 R35A S 0.7 7.5 2100 2500 40 (h), 50 (p), 55 (mp) 400 4 A 0.9 3.37 1600 1900 40 (sa/ca), 45 (ma) 400 4 R38A S 0.7 7.38 2200 2700 40 (h), 50 (p), 55 (mp) 400 4 A 0.9 3.31 1700 2100 40 (sa/ca), 45 (ma) 400 4 R40 S 0.7 6.75 2000 2000 40 (h), 50 (p), 55 (mp) 400 4 A 0.9 3.02 1600 1800 40 (sa/ca), 45 (ma) 400 4 R46 S 0.7 7.5 2700 3200 55 (h), 65 (p), 70 (mp) 400 4 A 0.9 3.36 2100 2600 55 (sa/ca), 60 (ma) 400 4 Key S – Steel A – Aluminium h – HPS200 ® by Corus p – Colorcoat ® PVDF mp – Metallic PVDF/Celestia ® by Corus sa – Stucco embossed aluminium ca – Coated aluminium ma – Metallic coated aluminium SS – Single span MS – Multi span Before ordering it is important to confirm with Corus Panels and Profiles which side of the profile carries the main surface finish. All profiles comply to current MCRMA Tolerances. * Factory curve only applies to 980 cover R13.5/3. R60 S 0.7 8.44 3300 3800 70 (h), 80 (p), 85 (mp) NA 4 A 0.9 3.78 2600 3200 70 (sa/ca), 75 (ma) NA 4 Clipfix 750 S 0.7 7.99 1500 1700 60 (h) N/A 1 A 0.9 4.20 1400 1600 50 (sa), 55 (ca/ma) N/A 1 Seam-loc S 0.7 7.99 1300 1800 65 (h) 16000 (h) 1.5 35000 (p) 38000 (mp) convex ALU-SEAM ® A 0.9 3.75 1500 2000 30 (sa/ca), 35 (ma) 8000 1.5 convex Del Monte Unit, Team Valley, Tyneside. Roof & Wall - Site Assembled Systems 5
Page 1 and 2: Corus Panels and Profiles Roof and
Page 3: Introduction Corus Panels and Profi
Page 7 and 8: Standard Wall Profile Range Materia
Page 9 and 10: Standard Lining Profiles Range Mate
Page 11 and 12: Lining Trays & Special Roof Profile
Page 13 and 14: Special Wall Profiles Left: The Eni
Page 15 and 16: Pressed Profiles Pressed profiles,
Page 17 and 18: Introduction Firewall System Select
Page 19 and 20: 4 Hour 15 minutes Insulation 4 Hour
Page 21 and 22: 4 Hour 30 minutes Insulation 4 Hour
Page 23 and 24: 4 Hour 15 Minutes Insulation 4 Hour
Page 25 and 26: 4 Hour 15 Minutes Insulation 4 Hour
Page 27 and 28: Building Regulations Firewall Build
Page 29 and 30: Acoustics Acoustic Systems Acoustic
Page 31 and 32: Acoustic Systems Sound Reduction In
Page 33 and 34: Acoustic Systems Sound Reduction an
Page 35 and 36: Acoustic Systems Sound Reduction St

Roof and Wall - Lane Roofing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?