Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

More documents

Recommendations

Info

Parameters 04/03 1.2 Quick commissioning (P0010=1) The following parameters are necessary for quick commissioning (P0010=1). No Name Access level P0100 Europe / North America 1 C P0304 Motor voltage rating 1 C P0305 Motor current rating 1 C P0307 Motor power rating 1 C P0308 Motor cosPhi rating 3 C P0309 Motor efficiency rating 3 C P0310 Motor frequency rating 1 C P0311 Motor speed rating 1 C P0335 Motor cooling 3 CT P0640 Motor overload factor [%] 3 CUT P0700 Selection of command source 1 CT P1000 Selection of frequency setpoint 1 CT P1080 Min. frequency 1 CUT P1082 Max. frequency 1 CT P1120 Ramp-up time 1 CUT P1121 Ramp-down time 1 CUT P1135 OFF3 ramp-down time 3 CUT P1300 Control mode 2 CT P3900 End of quick commissioning 1 C Cstat When P0010 = 1 is chosen, P0003 (user access level) can be used to select the parameters to be accessed. This parameter also allows selection of a user-defined parameter list for quick commissioning. At the end of the quick commissioning sequence, set P3900 = 1 to carry out the necessary motor calculations and clear all other parameters (not included in P0010=1) to their default settings. NOTE This applies only in Quick Commissioning mode. Reset to Factory default To reset all parameters to the factory default settings; the following parameters should be set as follows: Set P0010 = 30 Set P0970 = 1 NOTE The reset process takes approximately 10 seconds to complete. Parameter List SINAMICS G110 10 6SL3298-0BA11-0BP0
04/03 Parameters Seven-segment display The seven-segment display is structured as follows: Segment Bit 15 14 13 12 11 10 9 8 Segment Bit 7 6 5 4 3 2 1 0 The significance of the relevant bits in the display are described in the status and control word parameters. Parameter List SINAMICS G110 6SL3298-0BA11-0BP0 11
Page 1 and 2: Parameter List Edition 04/03 sinami
Page 3 and 4: Parameters 1 Faults and Alarms 2 Ap
Page 5: 04/03 Table of Contents Table of Co
Page 8 and 9: Parameters 04/03 5. Datatype The da
Page 12 and 13: Parameters 04/03 1.3 Parameter Desc
Page 14 and 15: Parameters 04/03 r0019 CO/BO: BOP c
Page 16 and 17: Parameters 04/03 r0052 Bit08 "Devia
Page 18 and 19: Parameters 04/03 r0054 CO/BO: Act.
Page 20 and 21: Parameters 04/03 P0100 Europe / Nor
Page 22 and 23: Parameters 04/03 Code- No. G110 MLF
Page 24 and 25: Parameters 04/03 P0295 Inverter fan
Page 26 and 27: Parameters 04/03 P0310 Rated motor
Page 28 and 29: Parameters 04/03 P0610 Motor I2t te
Page 30 and 31: Parameters 04/03 P0700 Selection of
Page 32 and 33: Parameters 04/03 P0703 Function of
Page 34 and 35: Parameters 04/03 P0731 Function of
Page 36 and 37: Parameters 04/03 For scaling of the
Page 38 and 39: Parameters 04/03 P0802 Transfer dat
Page 40 and 41: Parameters 04/03 r0947[8] Last faul
Page 42 and 43: Parameters 04/03 P0971 Transfer dat
Page 44 and 45: Parameters 04/03 P1003 Fixed freque
Page 46 and 47: Parameters 04/03 P1058 JOG frequenc
Page 48 and 49: Parameters 04/03 P1080 Min. frequen
Page 50 and 51: Parameters 04/03 P1091 Skip frequen
Page 52 and 53: Parameters 04/03 P1134 Rounding typ
Page 54 and 55: Parameters 04/03 P1203 Search rate:
Page 56 and 57: Parameters 04/03 P1210 Fault F0003
Page 58 and 59: Parameters 04/03 P1232 DC braking c
Page 60 and 61:
Parameters 04/03 P1240 Configuratio
Page 62 and 63:
Parameters 04/03 V Quadratic V/f Vm
Page 64 and 65:
Parameters 04/03 P1312 Starting boo
Page 66 and 67:
Parameters 04/03 P1335 Slip compens
Page 68 and 69:
Parameters 04/03 P2012 USS PZD leng
Page 70 and 71:
Parameters 04/03 P2014 USS telegram
Page 72 and 73:
Parameters 04/03 P2106 External fau
Page 75 and 76:
04/03 Faults and Alarms 2 Faults an
Page 77 and 78:
04/03 Faults and Alarms F0055 BOP-E
Page 79 and 80:
04/03 Faults and Alarms 2.2 Alarm M
Page 81 and 82:
04/03 Appendix 3 Appendix 3.1 List
Page 83:
Suggestions and / or Corrections To
show all

Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?