Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

More documents

Recommendations

Info

Parameters 04/03 P1232 DC braking current Min: 0 CStat: CUT Datatype: U16 Unit: % Def: 100 P-Group: FUNC Active: Immediately QuickComm.: No Max: 250 Level 3 Defines level of DC current in [%] relative to rated motor current (P0305). The DC Brake (DC Injection Brake) can be issued observing the following dependencies: - OFF1 or OFF3 ==> see P1233 - DIN or USS ==> see below DIN P070x = 25 1 0 USS * ) ⏐f⏐ Ctrl. wd. 2 Bit09 f* DC braking f_set t f_act i P0347 t DC braking active t r0053 Bit 00 1 0 t Note: DC brake can be applied in drive states r0002 = 1, 4, 5 *) SINAMICS G110 CPM110 USS only Parameter List SINAMICS G110 58 6SL3298-0BA11-0BP0
04/03 Parameters P1233 Duration of DC braking Min: 0 CStat: CUT Datatype: U16 Unit: s Def: 0 P-Group: FUNC Active: Immediately QuickComm.: No Max: 250 Level 3 Defines duration for which DC injection braking is to be active following an OFF1 or OFF3 command. 1 ON OFF1/OFF3 OFF2 ⏐f⏐ P0347 OFF2 DC braking t t DC braking active t r0053 Bit 00 1 0 t P1233 2 ON OFF1/OFF3 OFF2 ⏐f⏐ P0347 OFF2 DC braking t t DC braking active OFF2 t r0053 Bit 00 1 0 P1233 t Parameter P1232 still controls the level of DC injection. Value: P1233 = 0 : Not active. P1233 = 1 - 250 : Active for the specified duration. Caution: With the DC braking, the kinetic energy of the motor is converted into heat in the motor. The drive could overheat if the remains in this status for an exessive period of time ! Notice: The DC braking function causes the motor to stop rapidly by applying a DC braking current. When the DC braking signal is applied, the inverter output pulses are blocked and the DC current not applied until the motor has been sufficiently demagnetized (demagnetization time is calculated automatically from motor data). Parameter List SINAMICS G110 6SL3298-0BA11-0BP0 59
Page 1 and 2:
Parameter List Edition 04/03 sinami
Page 3 and 4:
Parameters 1 Faults and Alarms 2 Ap
Page 5:
04/03 Table of Contents Table of Co
Page 8 and 9: Parameters 04/03 5. Datatype The da
Page 10 and 11: Parameters 04/03 1.2 Quick commissi
Page 12 and 13: Parameters 04/03 1.3 Parameter Desc
Page 14 and 15: Parameters 04/03 r0019 CO/BO: BOP c
Page 16 and 17: Parameters 04/03 r0052 Bit08 "Devia
Page 18 and 19: Parameters 04/03 r0054 CO/BO: Act.
Page 20 and 21: Parameters 04/03 P0100 Europe / Nor
Page 22 and 23: Parameters 04/03 Code- No. G110 MLF
Page 24 and 25: Parameters 04/03 P0295 Inverter fan
Page 26 and 27: Parameters 04/03 P0310 Rated motor
Page 28 and 29: Parameters 04/03 P0610 Motor I2t te
Page 30 and 31: Parameters 04/03 P0700 Selection of
Page 32 and 33: Parameters 04/03 P0703 Function of
Page 34 and 35: Parameters 04/03 P0731 Function of
Page 36 and 37: Parameters 04/03 For scaling of the
Page 38 and 39: Parameters 04/03 P0802 Transfer dat
Page 40 and 41: Parameters 04/03 r0947[8] Last faul
Page 42 and 43: Parameters 04/03 P0971 Transfer dat
Page 44 and 45: Parameters 04/03 P1003 Fixed freque
Page 46 and 47: Parameters 04/03 P1058 JOG frequenc
Page 48 and 49: Parameters 04/03 P1080 Min. frequen
Page 50 and 51: Parameters 04/03 P1091 Skip frequen
Page 52 and 53: Parameters 04/03 P1134 Rounding typ
Page 54 and 55: Parameters 04/03 P1203 Search rate:
Page 56 and 57: Parameters 04/03 P1210 Fault F0003
Page 60 and 61: Parameters 04/03 P1240 Configuratio
Page 62 and 63: Parameters 04/03 V Quadratic V/f Vm
Page 64 and 65: Parameters 04/03 P1312 Starting boo
Page 66 and 67: Parameters 04/03 P1335 Slip compens
Page 68 and 69: Parameters 04/03 P2012 USS PZD leng
Page 70 and 71: Parameters 04/03 P2014 USS telegram
Page 72 and 73: Parameters 04/03 P2106 External fau
Page 75 and 76: 04/03 Faults and Alarms 2 Faults an
Page 77 and 78: 04/03 Faults and Alarms F0055 BOP-E
Page 79 and 80: 04/03 Faults and Alarms 2.2 Alarm M
Page 81 and 82: 04/03 Appendix 3 Appendix 3.1 List
Page 83: Suggestions and / or Corrections To
show all

Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

Create successful ePaper yourself

Delete template?

Save as template?