Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

More documents

Recommendations

Info

Parameters 04/03 P0703 Function of digital input 2 Min: 0 CStat: CT Datatype: U16 Unit: - Def: 9 P-Group: COMMANDS Active: first confirm QuickComm.: No Max: 29 Selects function of digital input 2. Possible Settings: 0 Digital input disabled 1 ON/OFF1 2 ON reverse /OFF1 3 OFF2 - coast to standstill 4 OFF3 - quick ramp-down 9 Fault acknowledge 10 JOG right 11 JOG left 12 Reverse 13 MOP up (increase frequency) 14 MOP down (decrease frequency) 15 Fixed frequency (Direct selection) 16 Fixed frequency (Direct selection + ON) 21 Local/remote 25 DC brake enable 29 External trip Details: See P0701 (function of digital input 0). P0704 Function of digital input 3 Min: 0 CStat: CT Datatype: U16 Unit: - Def: 0 P-Group: COMMANDS Active: first confirm QuickComm.: No Max: 29 Level 2 Level 2 Selects function of digital input 3 (via analog input). Possible Settings: 0 Digital input disabled 1 ON/OFF1 2 ON reverse /OFF1 3 OFF2 - coast to standstill 4 OFF3 - quick ramp-down 9 Fault acknowledge 10 JOG right 11 JOG left 12 Reverse 13 MOP up (increase freq.) 14 MOP down (decrease freq.) 21 Local/remote 25 DC brake enable 29 External trip Details: See P0701 (function of digital input 0). Parameter List SINAMICS G110 32 6SL3298-0BA11-0BP0
04/03 Parameters P0719[2] Selection of cmd. & freq. setp. Min: 0 CStat: CT Datatype: U16 Unit: - Def: 0 P-Group: COMMANDS Active: first confirm QuickComm.: No Max: 55 Level 3 Central switch to select control command source for inverter. Command and setpoint sources can be changed independently. The tens digit chooses the command source and the units digit chooses the setpoint source. The two indices of this parameter are used for local/remote switching. The local/remote signal switches between these settings. The default setting is 0 for the first index (i.e. normal parameterization is active). The second index is for control via BOP (i.e. activating the local/remote signal will then switch to BOP). Possible Settings: 0 Cmd = P0700 Setpoint = P1000 1 Cmd = P0700 Setpoint = MOP setpoint 2 Cmd = P0700 Setpoint = Analog setpoint 3 Cmd = P0700 Setpoint = Fixed frequency 5 Cmd = P0700 Setpoint = USS 10 Cmd = BOP Setpoint = P1000 11 Cmd = BOP Setpoint = MOP setpoint 12 Cmd = BOP Setpoint = Analog setpoint 13 Cmd = BOP Setpoint = Fixed frequency 15 Cmd = BOP Setpoint = USS 50 Cmd = USS Setpoint = P1000 51 Cmd = USS Setpoint = MOP setpoint 52 Cmd = USS Setpoint = Analog setpoint 53 Cmd = USS Setpoint = Fixed frequency 55 Cmd = USS Setpoint = USS Index: P0719[0] : 1st Control source (Remote) P0719[1] : 2nd Control source (Local) Dependency: P0719 has higher priority than P0700 and P1000. Notice: Particularly useful when e.g. changing command source temporarily from P0700 = 2. Functional setting of digital inputs is not reset to default. r0722 CO/BO: Binary input values Min: - Datatype: U16 Unit: - Def: - P-Group: COMMANDS Max: - Level 3 Displays status of digital inputs. Bitfields: Bit00 Digital input 0 0 OFF 1 ON Bit01 Digital input 1 0 OFF 1 ON Bit02 Digital input 2 0 OFF 1 ON Bit03 Digital input 3 (via ADC) 0 OFF 1 ON Note: Segment is lit when signal is active. P0724 Debounce time for digital inputs Min: 0 CStat: CT Datatype: U16 Unit: - Def: 3 P-Group: COMMANDS Active: Immediately QuickComm.: No Max: 3 Level 3 Defines debounce time (filtering time) used for digital inputs. Possible Settings: 0 No debounce time 1 2.5 ms debounce time 2 8.2 ms debounce time 3 12.3 ms debounce time Parameter List SINAMICS G110 6SL3298-0BA11-0BP0 33
Page 1 and 2: Parameter List Edition 04/03 sinami
Page 3 and 4: Parameters 1 Faults and Alarms 2 Ap
Page 5: 04/03 Table of Contents Table of Co
Page 8 and 9: Parameters 04/03 5. Datatype The da
Page 10 and 11: Parameters 04/03 1.2 Quick commissi
Page 12 and 13: Parameters 04/03 1.3 Parameter Desc
Page 14 and 15: Parameters 04/03 r0019 CO/BO: BOP c
Page 16 and 17: Parameters 04/03 r0052 Bit08 "Devia
Page 18 and 19: Parameters 04/03 r0054 CO/BO: Act.
Page 20 and 21: Parameters 04/03 P0100 Europe / Nor
Page 22 and 23: Parameters 04/03 Code- No. G110 MLF
Page 24 and 25: Parameters 04/03 P0295 Inverter fan
Page 26 and 27: Parameters 04/03 P0310 Rated motor
Page 28 and 29: Parameters 04/03 P0610 Motor I2t te
Page 30 and 31: Parameters 04/03 P0700 Selection of
Page 34 and 35: Parameters 04/03 P0731 Function of
Page 36 and 37: Parameters 04/03 For scaling of the
Page 38 and 39: Parameters 04/03 P0802 Transfer dat
Page 40 and 41: Parameters 04/03 r0947[8] Last faul
Page 42 and 43: Parameters 04/03 P0971 Transfer dat
Page 44 and 45: Parameters 04/03 P1003 Fixed freque
Page 46 and 47: Parameters 04/03 P1058 JOG frequenc
Page 48 and 49: Parameters 04/03 P1080 Min. frequen
Page 50 and 51: Parameters 04/03 P1091 Skip frequen
Page 52 and 53: Parameters 04/03 P1134 Rounding typ
Page 54 and 55: Parameters 04/03 P1203 Search rate:
Page 56 and 57: Parameters 04/03 P1210 Fault F0003
Page 58 and 59: Parameters 04/03 P1232 DC braking c
Page 60 and 61: Parameters 04/03 P1240 Configuratio
Page 62 and 63: Parameters 04/03 V Quadratic V/f Vm
Page 64 and 65: Parameters 04/03 P1312 Starting boo
Page 66 and 67: Parameters 04/03 P1335 Slip compens
Page 68 and 69: Parameters 04/03 P2012 USS PZD leng
Page 70 and 71: Parameters 04/03 P2014 USS telegram
Page 72 and 73: Parameters 04/03 P2106 External fau
Page 75 and 76: 04/03 Faults and Alarms 2 Faults an
Page 77 and 78: 04/03 Faults and Alarms F0055 BOP-E
Page 79 and 80: 04/03 Faults and Alarms 2.2 Alarm M
Page 81 and 82: 04/03 Appendix 3 Appendix 3.1 List
Page 83:
Suggestions and / or Corrections To
show all

Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?