Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

More documents

Recommendations

Info

Parameters 04/03 r0054 CO/BO: Act. control word 1 Min: - Datatype: U16 Unit: - Def: - P-Group: COMMANDS Max: - Level 3 Displays first control word of inverter (in bit format) and can be used to diagnose which commands are active. Bitfields: Bit00 ON/OFF1 0 NO 1 YES Bit01 OFF2: Electrical stop 0 YES 1 NO Bit02 OFF3: Fast stop 0 YES 1 NO Bit03 Pulse enable 0 NO 1 YES Bit04 RFG enable 0 NO 1 YES Bit05 RFG start 0 NO 1 YES Bit06 Setpoint enable 0 NO 1 YES Bit07 Fault acknowledge 0 NO 1 YES Bit08 JOG right 0 NO 1 YES Bit09 JOG left 0 NO 1 YES Bit10 Control from PLC 0 NO 1 YES Bit11 Reverse (setpoint inversion) 0 NO 1 YES Bit13 Motor potentiometer MOP up 0 NO 1 YES Bit14 Motor potentiometer MOP down 0 NO 1 YES Bit15 Local / Remote 0 NO 1 YES Notice: Identical to r2036 if USS is selected as command source via P0700 or P0719. Details: The 7-segment display of the bit-parameters (binary parameters) is explained in the Introduction of the Parameter List. r0055 CO/BO: Act. control word 2 Min: - Datatype: U16 Unit: - Def: - P-Group: COMMANDS Max: - Displays additional control word of inverter (in bit format) and can be used to diagnose which commands are active. Bitfields: Bit00 Fixed frequency Bit 0 0 NO 1 YES Bit01 Fixed frequency Bit 1 0 NO 1 YES Bit02 Fixed frequency Bit 2 0 NO 1 YES Bit09 Enable DC brake 0 NO 1 YES Bit13 External fault 1 0 YES 1 NO Notice: Identical to r2037 if USS is selected as command source via P0700 or P0719. Details: The 7-segment display of the bit-parameters (binary parameters) is explained in the Introduction of the Parameter List. r0056 CO/BO: Status of motor control Min: - Datatype: U16 Unit: - Def: - P-Group: CONTROL Max: - Displays status of motor control (in bit format), which can be used to diagnose inverter status. Bitfields: Bit00 Init. control finished 0 NO 1 YES Bit01 Motor demagnetizing finished 0 NO 1 YES Bit02 Pulses enabled 0 NO 1 YES Bit04 Motor excitation finished 0 NO 1 YES Bit05 Starting boost active 0 NO 1 YES Bit06 Acceleration boost active 0 NO 1 YES Bit07 Frequency is negative 0 NO 1 YES Bit08 Field weakening active 0 NO 1 YES Bit09 Volts setpoint limited 0 NO 1 YES Bit10 Slip frequency limited 0 NO 1 YES Bit13 I-max controller active 0 NO 1 YES Bit14 Vdc-max controller active 0 NO 1 YES Notice: The I-max controller (r0056 Bit13) will be activated when the actual output current (r0027) exceeds the current limit in r0067. Details: See description of seven-segment display given in the introduction. Level 3 Level 2 Parameter List SINAMICS G110 18 6SL3298-0BA11-0BP0
04/03 Parameters r0067 CO: Act. output current limit Min: - Datatype: Float Unit: A Def: - P-Group: CONTROL Max: - Level 3 Displays valid maximum output current of inverter. P0305 Motor Inverter P0640 r0209 Motor protection Inverter protection Min r0067 Dependency: This value is influenced by P0640 (Motor overload factor), the derating characteristics and the thermal motor and inverter protection. Note: P0610 (motor I2t temperature reaction) and P0290 (inverter overload reaction) define reaction when limit is reached. Normally : - current limit (r0067) = rated motor current P0305 x motor overload factor P0640. - It is less than or equal to maximum inverter current r0209. The current limit may be reduced if the motor or inverter thermal model calculation indicates that overheating will occur. Parameter List SINAMICS G110 6SL3298-0BA11-0BP0 19
Page 1 and 2: Parameter List Edition 04/03 sinami
Page 3 and 4: Parameters 1 Faults and Alarms 2 Ap
Page 5: 04/03 Table of Contents Table of Co
Page 8 and 9: Parameters 04/03 5. Datatype The da
Page 10 and 11: Parameters 04/03 1.2 Quick commissi
Page 12 and 13: Parameters 04/03 1.3 Parameter Desc
Page 14 and 15: Parameters 04/03 r0019 CO/BO: BOP c
Page 16 and 17: Parameters 04/03 r0052 Bit08 "Devia
Page 20 and 21: Parameters 04/03 P0100 Europe / Nor
Page 22 and 23: Parameters 04/03 Code- No. G110 MLF
Page 24 and 25: Parameters 04/03 P0295 Inverter fan
Page 26 and 27: Parameters 04/03 P0310 Rated motor
Page 28 and 29: Parameters 04/03 P0610 Motor I2t te
Page 30 and 31: Parameters 04/03 P0700 Selection of
Page 32 and 33: Parameters 04/03 P0703 Function of
Page 34 and 35: Parameters 04/03 P0731 Function of
Page 36 and 37: Parameters 04/03 For scaling of the
Page 38 and 39: Parameters 04/03 P0802 Transfer dat
Page 40 and 41: Parameters 04/03 r0947[8] Last faul
Page 42 and 43: Parameters 04/03 P0971 Transfer dat
Page 44 and 45: Parameters 04/03 P1003 Fixed freque
Page 46 and 47: Parameters 04/03 P1058 JOG frequenc
Page 48 and 49: Parameters 04/03 P1080 Min. frequen
Page 50 and 51: Parameters 04/03 P1091 Skip frequen
Page 52 and 53: Parameters 04/03 P1134 Rounding typ
Page 54 and 55: Parameters 04/03 P1203 Search rate:
Page 56 and 57: Parameters 04/03 P1210 Fault F0003
Page 58 and 59: Parameters 04/03 P1232 DC braking c
Page 60 and 61: Parameters 04/03 P1240 Configuratio
Page 62 and 63: Parameters 04/03 V Quadratic V/f Vm
Page 64 and 65: Parameters 04/03 P1312 Starting boo
Page 66 and 67: Parameters 04/03 P1335 Slip compens
Page 68 and 69:
Parameters 04/03 P2012 USS PZD leng
Page 70 and 71:
Parameters 04/03 P2014 USS telegram
Page 72 and 73:
Parameters 04/03 P2106 External fau
Page 75 and 76:
04/03 Faults and Alarms 2 Faults an
Page 77 and 78:
04/03 Faults and Alarms F0055 BOP-E
Page 79 and 80:
04/03 Faults and Alarms 2.2 Alarm M
Page 81 and 82:
04/03 Appendix 3 Appendix 3.1 List
Page 83:
Suggestions and / or Corrections To
show all

Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

Create successful ePaper yourself

Delete template?

Save as template?