Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

More documents

Recommendations

Info

Important Information 04/03 Important Information This Parameter List must only be used in conjunction with the Operating Instructions of the SINAMICS G110. WARNING Please pay special attention to the Warnings, Cautions, Notices and Notes contained in the Operating Instructions. You will find the Operating Instructions on the Docu CD which can be ordered via your local Siemens department under the Order No. 6SL3271-0CA00-0AG0 or downloaded from our website http://www.siemens.com/sinamics. Approved Siemens Quality for Software and Training is to DIN ISO 9001, Reg. No. 2160-01 The reproduction, transmission or use of this document, or its contents is not permitted unless authorized in writing. Offenders will be liable for damages. All rights including rights created by patent grant or registration of a utility model or design are reserved. © Siemens AG 2003. All Rights Reserved. SINAMICS® is a registered trademark of Siemens Other functions not described in this document may be available. However, this fact shall not constitute an obligation to supply such functions with a new control, or when servicing. We have checked that the contents of this document correspond to the hardware and software described. There may be discrepancies nevertheless, and no guarantee can be given that they are completely identical. The information contained in this document is reviewed regularly and any necessary changes will be included in the next edition. We welcome suggestions for improvement. Siemens handbooks are printed on chlorine-free paper that has been produced from managed sustainable forests. No solvents have been used in the printing or binding process. Document subject to change without prior notice. Printed in the Federal Republic of Germany Siemens-Aktiengesellschaft. SINAMICS G110 Parameter List 4 6SL3298-0BA11-0BP0
04/03 Table of Contents Table of Contents 1 Parameters .............................................................................................................. 7 1.1 Introduction to SINAMICS G110 System Parameters.............................................. 7 1.2 Quick commissioning (P0010=1)............................................................................ 10 1.3 Parameter Description ............................................................................................ 12 2 Faults and Alarms................................................................................................. 75 2.1 Fault messages....................................................................................................... 75 2.2 Alarm Messages ..................................................................................................... 79 3 Appendix .............................................................................................................. 81 3.1 List of Abbreviations................................................................................................ 81 Parameter List SINAMICS G110 6SL3298-0BA11-0BP0 5
Page 1 and 2: Parameter List Edition 04/03 sinami
Page 3: Parameters 1 Faults and Alarms 2 Ap
Page 8 and 9: Parameters 04/03 5. Datatype The da
Page 10 and 11: Parameters 04/03 1.2 Quick commissi
Page 12 and 13: Parameters 04/03 1.3 Parameter Desc
Page 14 and 15: Parameters 04/03 r0019 CO/BO: BOP c
Page 16 and 17: Parameters 04/03 r0052 Bit08 "Devia
Page 18 and 19: Parameters 04/03 r0054 CO/BO: Act.
Page 20 and 21: Parameters 04/03 P0100 Europe / Nor
Page 22 and 23: Parameters 04/03 Code- No. G110 MLF
Page 24 and 25: Parameters 04/03 P0295 Inverter fan
Page 26 and 27: Parameters 04/03 P0310 Rated motor
Page 28 and 29: Parameters 04/03 P0610 Motor I2t te
Page 30 and 31: Parameters 04/03 P0700 Selection of
Page 32 and 33: Parameters 04/03 P0703 Function of
Page 34 and 35: Parameters 04/03 P0731 Function of
Page 36 and 37: Parameters 04/03 For scaling of the
Page 38 and 39: Parameters 04/03 P0802 Transfer dat
Page 40 and 41: Parameters 04/03 r0947[8] Last faul
Page 42 and 43: Parameters 04/03 P0971 Transfer dat
Page 44 and 45: Parameters 04/03 P1003 Fixed freque
Page 46 and 47: Parameters 04/03 P1058 JOG frequenc
Page 48 and 49: Parameters 04/03 P1080 Min. frequen
Page 50 and 51: Parameters 04/03 P1091 Skip frequen
Page 52 and 53: Parameters 04/03 P1134 Rounding typ
Page 54 and 55:
Parameters 04/03 P1203 Search rate:
Page 56 and 57:
Parameters 04/03 P1210 Fault F0003
Page 58 and 59:
Parameters 04/03 P1232 DC braking c
Page 60 and 61:
Parameters 04/03 P1240 Configuratio
Page 62 and 63:
Parameters 04/03 V Quadratic V/f Vm
Page 64 and 65:
Parameters 04/03 P1312 Starting boo
Page 66 and 67:
Parameters 04/03 P1335 Slip compens
Page 68 and 69:
Parameters 04/03 P2012 USS PZD leng
Page 70 and 71:
Parameters 04/03 P2014 USS telegram
Page 72 and 73:
Parameters 04/03 P2106 External fau
Page 75 and 76:
04/03 Faults and Alarms 2 Faults an
Page 77 and 78:
04/03 Faults and Alarms F0055 BOP-E
Page 79 and 80:
04/03 Faults and Alarms 2.2 Alarm M
Page 81 and 82:
04/03 Appendix 3 Appendix 3.1 List
Page 83:
Suggestions and / or Corrections To
show all

Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?