Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

More documents

Recommendations

Info

Parameters 04/03 P1134 Rounding type Min: 0 CStat: CUT Datatype: U16 Unit: - Def: 0 P-Group: SETPOINT Active: Immediately QuickComm.: No Max: 1 Level 3 Defines the smoothing which is active by setpoint modifications during acceleration or deceleration (e.g. new setpoint, OFF1, OFF3, REV). This smoothing is applied, if the motor is ramped-up or ramped-down and - P1134 = 0, - P1130 > 0 and - the setpoint is not yet reached. P1130 > 0 f Set f Setpoint reached P1134 = 0 Setpoint not reached t f P1130 f Set Setpoint reached P1134 = 1 Setpoint not reached t ON OFF1 P1130 Possible Settings: 0 Continuous smoothing 1 Discontinuous smoothing Dependency: This parameter has no effect unless the value set in P1130 is greater than 0. P1135 OFF3 ramp-down time Min: 0.00 CStat: CUT Datatype: Float Unit: s Def: 5.00 P-Group: SETPOINT Active: first confirm QuickComm.: Yes Max: 650.00 t Level 3 Defines ramp-down time from maximum frequency to standstill for OFF3 command. Settings in P1130 and P1134 will have no effect on OFF3 ramp-down characteristic. An initial ramp-down rounding time of approaximately 10% of P1135 is however included. For the total OFF3 ramp-down time: tdown,OFF3 = 1.1 ⋅ P1135 Note: This time may be exceeded if the VDC_max. level is reached. r1170 CO: Frequency setpoint after RFG Min: - Datatype: Float Unit: Hz Def: - P-Group: SETPOINT Max: - Displays overall frequency setpoint after ramp generator. Level 3 Parameter List SINAMICS G110 52 6SL3298-0BA11-0BP0
04/03 Parameters P1200 Flying start Min: 0 CStat: CUT Datatype: U16 Unit: - Def: 0 P-Group: FUNC Active: first confirm QuickComm.: No Max: 6 Level 3 Starts inverter onto a spinning motor by rapidly changing the output frequency of the inverter until the actual motor speed has been found. Then, the motor runs up to setpoint using the normal ramp time. (f max + 2f slip nom ) 'ramps to set point with normal ramp' fout t P1202 I out I dc Vn as per V/f characteristic V out 'motor speed found' Possible Settings: 0 Flying start disabled 1 Flying start is always active, start in direction of setpoint 2 Flying start is active if power on, fault, OFF2, start in direction of setpoint 3 Flying start is active if fault, OFF2, start in direction of setpoint 4 Flying start is always active, only in direction of setpoint 5 Flying start is active if power on, fault, OFF2, only in direction of setpoint 6 Flying start is active if fault, OFF2, only in direction of setpoint Note: Useful for motors with high inertia loads. Settings 1 to 3 search in both directions. Settings 4 to 6 search only in direction of setpoint. Notice: Flying start must be used in cases where the motor may still be turning (e.g. after a short mains break) or can be driven by the load. Otherwise, overcurrent trips will occur. P1202 Motor-current: Flying start Min: 10 CStat: CUT Datatype: U16 Unit: % Def: 100 P-Group: FUNC Active: first confirm QuickComm.: No Max: 200 Defines search current used for flying start. Level 3 Note: Value is in [%] based on rated motor current (P0305). Reducing the search current may improve performance for flying start if the inertia of the system is not very high. Parameter List SINAMICS G110 6SL3298-0BA11-0BP0 53
Page 1 and 2: Parameter List Edition 04/03 sinami
Page 3 and 4: Parameters 1 Faults and Alarms 2 Ap
Page 5: 04/03 Table of Contents Table of Co
Page 8 and 9: Parameters 04/03 5. Datatype The da
Page 10 and 11: Parameters 04/03 1.2 Quick commissi
Page 12 and 13: Parameters 04/03 1.3 Parameter Desc
Page 14 and 15: Parameters 04/03 r0019 CO/BO: BOP c
Page 16 and 17: Parameters 04/03 r0052 Bit08 "Devia
Page 18 and 19: Parameters 04/03 r0054 CO/BO: Act.
Page 20 and 21: Parameters 04/03 P0100 Europe / Nor
Page 22 and 23: Parameters 04/03 Code- No. G110 MLF
Page 24 and 25: Parameters 04/03 P0295 Inverter fan
Page 26 and 27: Parameters 04/03 P0310 Rated motor
Page 28 and 29: Parameters 04/03 P0610 Motor I2t te
Page 30 and 31: Parameters 04/03 P0700 Selection of
Page 32 and 33: Parameters 04/03 P0703 Function of
Page 34 and 35: Parameters 04/03 P0731 Function of
Page 36 and 37: Parameters 04/03 For scaling of the
Page 38 and 39: Parameters 04/03 P0802 Transfer dat
Page 40 and 41: Parameters 04/03 r0947[8] Last faul
Page 42 and 43: Parameters 04/03 P0971 Transfer dat
Page 44 and 45: Parameters 04/03 P1003 Fixed freque
Page 46 and 47: Parameters 04/03 P1058 JOG frequenc
Page 48 and 49: Parameters 04/03 P1080 Min. frequen
Page 50 and 51: Parameters 04/03 P1091 Skip frequen
Page 54 and 55: Parameters 04/03 P1203 Search rate:
Page 56 and 57: Parameters 04/03 P1210 Fault F0003
Page 58 and 59: Parameters 04/03 P1232 DC braking c
Page 60 and 61: Parameters 04/03 P1240 Configuratio
Page 62 and 63: Parameters 04/03 V Quadratic V/f Vm
Page 64 and 65: Parameters 04/03 P1312 Starting boo
Page 66 and 67: Parameters 04/03 P1335 Slip compens
Page 68 and 69: Parameters 04/03 P2012 USS PZD leng
Page 70 and 71: Parameters 04/03 P2014 USS telegram
Page 72 and 73: Parameters 04/03 P2106 External fau
Page 75 and 76: 04/03 Faults and Alarms 2 Faults an
Page 77 and 78: 04/03 Faults and Alarms F0055 BOP-E
Page 79 and 80: 04/03 Faults and Alarms 2.2 Alarm M
Page 81 and 82: 04/03 Appendix 3 Appendix 3.1 List
Page 83: Suggestions and / or Corrections To

Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

Create successful ePaper yourself

Delete template?

Save as template?