Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

More documents

Recommendations

Info

Parameters 04/03 P0731 Function of digital output 0 Min: 0 CStat: CUT Datatype: U16 Unit: - Def: 5 P-Group: COMMANDS Active: first confirm QuickComm.: No Max: 22 Defines source of digital output 0. Possible Settings: 0 Not Active 1 Active 2 Drive ready 3 Drive ready to run 4 Drive running 5 Drive fault active 6 OFF2 active 7 OFF3 active 8 Switch on inhibit active 9 Drive warning active 10 Deviation value 11 PZD control 12 Maximum frequency reached 13 Warning: Motor current limit 14 Motor holding brake active 15 Motor overload 16 Motor running direction right 17 Inverter overload 18 DC brake active 19 Act. freq > P2167 20 Act. freq > P1080 (f_min) 21 Act. freq >= setpoint 22 Ramping finish Note: Output of fault bit 52.3 is inverted on digital output. Details: See parameter r0052, r0053. r0747 CO/BO: State of digital outputs Min: - Datatype: U16 Unit: - Def: - P-Group: COMMANDS Max: - Level 3 Level 3 Displays status of digital outputs (also includes inversion of digital outputs via P0748). Bitfields: Bit00 Digital output 0 energized 0 NO 1 YES Dependency: Bit 0 = 0 : Optocoupler contacts open Bit 0 = 1 : Optocoupler contacts closed P0748 Invert digital outputs Min: 0 CStat: CUT Datatype: U16 Unit: - Def: 0 P-Group: COMMANDS Active: first confirm QuickComm.: No Max: 1 Defines high and low states of relay for a given function. Bitfields: Bit00 Invert digital output 0 0 NO 1 YES r0752 Act. input of ADC Min: - Datatype: Float Unit: V Def: - P-Group: TERMINAL Max: - Level 3 Level 3 Displays smoothed analog input value in volts before the characteristic block. KL8 +10 V KL9 KL10 A D P0753 P0757 P0758 P0759 P0760 ADC scaling r0754 P0761 ADC dead zone P1000 = 2 Setpoint r0752 P0704 = x 1 1.7 V 0 3.9 V r0722 r0722.3 Function Parameter List SINAMICS G110 34 6SL3298-0BA11-0BP0
04/03 Parameters P0753 Smooth time ADC Min: 0 CStat: CUT Datatype: U16 Unit: ms Def: 3 P-Group: TERMINAL Active: first confirm QuickComm.: No Max: 10000 Level 3 Note: Defines filter time (PT1 filter) in [ms] for analog input. Increasing this time (smooth) reduces jitter but slows down response to the analog input. P0753 = 0 : No filtering r0754 Act. ADC value after scaling [%] Min: - Datatype: Float Unit: % Def: - P-Group: TERMINAL Max: - Shows smoothed value of analog input in [%] after scaling block. Dependency: P0757 to P0760 define range (ADC scaling). P0757 Value x1 of ADC scaling Min: 0 CStat: CUT Datatype: Float Unit: V Def: 0 P-Group: TERMINAL Active: first confirm QuickComm.: No Max: 10 Level 2 Level 3 Parameters P0757 - P0760 configure the input scaling as shown in the diagram: P0761 = 0 100 % % ASPmax 4000 h P0760 P0757 P0759 10 V x 100% V P0758 ASPmin Note: Where: - Analog setpoints represent a [%] of the normalized frequency in P2000. - Analog setpoints may be larger than 100 %. - ASPmax represents highest analog setpoint (this may be at 10 V). - ASPmin represents lowest analog setpoint (this may be at 0 V). - Default values provide a scaling of 0 V = 0 %, and 10 V = 100 %. The ADC-linear characteristic is described by 4 coordinates, based on a two-point equation: y - P0758 P0760 − P0758 = x - P0757 P0759 − P0757 For calculations the point-gradient form (offset and gradient) is more advantageous: y = m ⋅ x + y0 The transformation between these two forms is given by: P0760 − P0758 m = P0759 − P0757 y0 P0758 ⋅P0759 − P0757 ⋅P0760 = P0759 − P0757 Parameter List SINAMICS G110 6SL3298-0BA11-0BP0 35
Page 1 and 2: Parameter List Edition 04/03 sinami
Page 3 and 4: Parameters 1 Faults and Alarms 2 Ap
Page 5: 04/03 Table of Contents Table of Co
Page 8 and 9: Parameters 04/03 5. Datatype The da
Page 10 and 11: Parameters 04/03 1.2 Quick commissi
Page 12 and 13: Parameters 04/03 1.3 Parameter Desc
Page 14 and 15: Parameters 04/03 r0019 CO/BO: BOP c
Page 16 and 17: Parameters 04/03 r0052 Bit08 "Devia
Page 18 and 19: Parameters 04/03 r0054 CO/BO: Act.
Page 20 and 21: Parameters 04/03 P0100 Europe / Nor
Page 22 and 23: Parameters 04/03 Code- No. G110 MLF
Page 24 and 25: Parameters 04/03 P0295 Inverter fan
Page 26 and 27: Parameters 04/03 P0310 Rated motor
Page 28 and 29: Parameters 04/03 P0610 Motor I2t te
Page 30 and 31: Parameters 04/03 P0700 Selection of
Page 32 and 33: Parameters 04/03 P0703 Function of
Page 36 and 37: Parameters 04/03 For scaling of the
Page 38 and 39: Parameters 04/03 P0802 Transfer dat
Page 40 and 41: Parameters 04/03 r0947[8] Last faul
Page 42 and 43: Parameters 04/03 P0971 Transfer dat
Page 44 and 45: Parameters 04/03 P1003 Fixed freque
Page 46 and 47: Parameters 04/03 P1058 JOG frequenc
Page 48 and 49: Parameters 04/03 P1080 Min. frequen
Page 50 and 51: Parameters 04/03 P1091 Skip frequen
Page 52 and 53: Parameters 04/03 P1134 Rounding typ
Page 54 and 55: Parameters 04/03 P1203 Search rate:
Page 56 and 57: Parameters 04/03 P1210 Fault F0003
Page 58 and 59: Parameters 04/03 P1232 DC braking c
Page 60 and 61: Parameters 04/03 P1240 Configuratio
Page 62 and 63: Parameters 04/03 V Quadratic V/f Vm
Page 64 and 65: Parameters 04/03 P1312 Starting boo
Page 66 and 67: Parameters 04/03 P1335 Slip compens
Page 68 and 69: Parameters 04/03 P2012 USS PZD leng
Page 70 and 71: Parameters 04/03 P2014 USS telegram
Page 72 and 73: Parameters 04/03 P2106 External fau
Page 75 and 76: 04/03 Faults and Alarms 2 Faults an
Page 77 and 78: 04/03 Faults and Alarms F0055 BOP-E
Page 79 and 80: 04/03 Faults and Alarms 2.2 Alarm M
Page 81 and 82: 04/03 Appendix 3 Appendix 3.1 List
Page 83: Suggestions and / or Corrections To

Parameter List Edition 04/03 SINAMICS G110 - Automatyka Siemens

Create successful ePaper yourself

Delete template?

Save as template?