Emotron VSA Variable Speed Drive

More documents

Recommendations

Info

2.2 Mounting and installation Do not use the VSD in an environment with the following conditions: Oil Direct sunlight Corrosive gas and liquid Oil mist Salt Salt Exposed to wind, rain and water Iron filings, dust Strong vibration Extremely low Excessively high temperatures temperatures Electromagnetic waves and ultra high frequency waves (Near an electric welding machine) Radioactive materials Inflammable materials Emotron AB 01-3993-01r3 Mounting and installation of the VSA drive 9
2.3 Wiring Rules 2.3.1 Notice for wiring Tightening torque: Connect cables with a screwdriver or other suitable tools per the tightening torques listed below. Type VSA23-01/ 03/04 Power source 200-240V VSA23-07/10 200-240V VSA48-002/ 004/005 380-480V Securing torque Tightening torque for TM1 terminal 0.74/0.1 (LBS-FT / KG-M) 1.286/0.18 (LBS-FT/KG-M) 8.66/10 (LBS-IN/KG- CM) 15.97/18 (LBS-IN/KG- CM) B. Power wires: Power wires connect to terminals L1, L2, L3, T1, T2, T3, P and N. Select power wire in accordance with the following criteria: 1. Use wires with copper core only. Insulating materials with diameters should be based on working conditions at 221F (105C). 2. The minimum nominal voltage of 240 VAC type connectors is 300 V, and 480 VAC type connector is 600 V. C. Control wire: Control wire is connected to the TM2 control terminal. Select wire in accordance with the following criteria: 1. Use copper core only. The insulating materials with diameters should be based on working conditions at 221F (105C). 2. To avoid noise interference, do not route the control wiring in the same conduit with power wires and motor wiring. D. Nominal electrical specifications of the terminal block: The following are nominal values of TM1: E. Fuse types Drive input fuses are provided to disconnect the drive from power in the event that a component fails in the drive’s power circuitry. The drive’s electronic protection circuitry is designed to clear drive output short circuits and ground faults without blowing the drive input fuses. Below table shows the EV input fuse ratings. To protect the VSD most effectively, use fuses with currentlimit function. RK5, CC/T type fuse for VSA 220V class(1) VSA model 440V class(3) HP kW kVA 100% CONT Output AMPS (A) Max. RK5 FUSE Rating (A) VSA23-01 0.25 0.2 0.53 1.7 8 15 VSA23-03 0.5 0.4 0.88 3.1 10 20 VSA23-04 1 0.75 1.6 4.2 15 30 VSA23-07 2 1.5 2.9 7.5 20 40 VSA23-10 3 2.2 4.0 10.5 25 50 VSA model HP kW kVA 100% CONT Output AMPS (A) Max.RK5 FUSE Rating (A) VSA48-002 1 0.75 1.7 2.3 6 10 VSA48-004 2 1.5 2.9 3.8 10 15 VSA48-005 3 2.2 4.0 5.2 10 20 Max.CC or T FUSE Rating (A) Max.CC or T FUSE Rating (A) *Fuse ratings are based upon 300 V fuses for 230 V VSDs, and 500 V for 460 V VSDs Type Power source Volts Amps VSA23-01/03/04 200-240V 600 15 VSA23-07/10 200-240V VSA48-002/004/005 380-480V 600 40 NOTE: Nominal values of input and output signals (TM2) – follow the specifications of class 2 wiring. 10 Mounting and installation of the VSA drive Emotron AB 01-3993-01r3
Page 1 and 2: Emotron VSA Variable Speed Drive In
Page 3 and 4: Emotron AB 01-3993-01r3
Page 5 and 6: Emotron AB 01-3993-01r3
Page 7 and 8: 2 Emotron AB 01-3993-01r3
Page 9 and 10: Before operation ! Leakage current
Page 11 and 12: 6 Model description Emotron AB 01-3
Page 13: 1 3 2 2 A. DIN-rail installation 1
Page 17 and 18: 2.3.3 Precautions for peripheral ap
Page 19 and 20: • When the connection between the
Page 21 and 22: Over load protection International
Page 23 and 24: 2.6 Description of VSD Terminal Des
Page 25 and 26: + IP20 Frame 2: Three phase: VSA48-
Page 27 and 28: 22 Mounting and installation of the
Page 29 and 30: Remote/Local change function • Lo
Page 31 and 32: Menu Function Description Range/ Co
Page 37 and 38: (2) Input signal is PNP (2) Input s
Page 39 and 40: Corresponding list of current and c
Page 41 and 42: Master Slave (VSA response) T1 T2 T
Page 43 and 44: estart after the RUN switch was tur
Page 45 and 46: When the motor is vibrating excessi
Page 47 and 48: • Operating frequency range: 0 to
Page 49 and 50: 416 Max Alarm Margin: 0-400% The ma
Page 51 and 52: Priority of the frequencies: Jog >
Page 53 and 54: The setting of figure 1: The settin
Page 55 and 56: nal has been released. The drive co
Page 57 and 58: [531]=004 Rated current Example: th
Page 59 and 60: [551]/[541]=004 Frequency detection
Page 61 and 62: 56 Programming instructions and men
Page 63 and 64: Errors which can only be recovered
Page 65 and 66:
4.2 General functional troubleshoot
Page 67 and 68:
* from previous page Check the menu
Page 69 and 70:
Troubleshooting for OV, LV error di
Page 71 and 72:
Motor is overheated Is the measured
Page 73 and 74:
68 Troubleshooting and maintenance
Page 75 and 76:
RS232 wiring diagram 5.2.4 Remote k
Page 77 and 78:
72 Peripherals Emotron AB 01-3993-0
Page 79 and 80:
331 412 613 332 413 614 333 414 811
show all

Emotron VSA Variable Speed Drive

Create successful ePaper yourself

Delete template?

Save as template?