User Manual - AMS Neve

More documents

Recommendations

Info

SynchroNet ES/2 User Guide Getting Started Serial*Share Video Syncs (optional) RS422 Bus A SynchroNet ES/2 Serial Control AudioFile A B ltc / vitc VCR Console Automation A B SynchroNet ES/2 Parallel Control ltc ATR Ltc (Play / Sync) From Timecode bus SynchroNet ES/2 Serial Control A B ltc DAT Penta A B SynchroNet ES/2 BiPhase FILM Selecting emulation mode on bus A and EXT mode on bus B provides the ability to integrate a Penta controller with the single machine control provided by most console or hard disk editors. For example this may be Adams Smith Zeta 3 Emulation with a Neve Capricorn or Sony Emulation with a ScreenSound/Scenaria. Setting up Connect all units together on both buses. If video resolve modes are to be used then connect video syncs to all ES/2s. Connect bus A to the non ESbus controller using the appropriate Emulator cable. Connect bus B to the Penta/CPSU. Hard reset to all modules. This will default to EXT(ernal) mode. Select the correct machine interface for each unit and CALibrate. Select the Emulating ES/2 to EMUL mode. This will automatically set the unit to bus A. On the emulating ES/2 use the PROTO softkey in the System Menu to select the correct communications protocol for the controller. Issue 2 2:13
Getting Started SynchroNet ES/2 User Guide Press the Bus B softkey in the System Menu to set bus B to EXT (external). The PROTO softkey will be replaced by the ESbus menu softkey. Use the System ESbus Menu to set appropriate ESbus addresses for all modules. In the Mode Select Menu, set the remaining ES/2s to EXT (external mode) and switch to bus B. Set all units ON BUS. On the Penta the emulating ES/2 will automatically set itself as a Remote Master. The EMULating ES/2 will now be the timeline master on both buses. Check that the reference is as required (usually video). Notes on Operation Penta software revision 1.22 or later is required Selecting a new Remote Master on Penta will automatically enable the emulator on the new master and disable the emulator on the old master. The machine position returned to the controller will reflect the position of the new master machine The selected master will show a solid LED on bus A select and a flashing LED on bus B select. Both comms activity LEDs will flash with incoming messages from their respective sources. The other ES/2s in the system will show flashing bus B select leds only. Some controllers (in particular video machines selected to PLAYER mode) will cancel communications with the system as a result of the interruption switching masters entails. If this happens restart the controller comms. The system offers you three control surfaces. It will run and lock when responding to commands from the Penta, from the remote non-ESbus control source or from the transport controls of the master machine itself. Some operations are mutually exclusive, for example if you locate the system using the remote control source, you cannot cancel that operation by pressing STOP on the machine. Timecode bus The ES/2 selected as the master will automatically become the master of the timecode bus on both A and B buses. Any ES/2 can be designated to put the timecode bus signal onto its generator output socket. This provides a patch free source of master machine timecode. 2:14 Issue 2
Page 1 and 2: SynchroNet ES/2 User Guide 527-193
Page 3 and 4: Contents SynchroNet ES/2 User Guide
Page 5 and 6: Introduction SynchroNet ES/2 User G
Page 7 and 8: Getting Started SynchroNet ES/2 Use
Page 17: Getting Started SynchroNet ES/2 Use
Page 29 and 30: ES/2 Operations Reference SynchroNe
Page 67 and 68: Appendix A - Abbreviations SynchroN
Page 69 and 70:
Appendix A - Abbreviations SynchroN
Page 71 and 72:
Appendix B - Menu Default Settings
Page 73 and 74:
Appendix C - ES/2 Connectors Synchr
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Appendix D - Machine Parameters Syn
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Appendix E - SSL ScreenSound Synchr
Page 89 and 90:
Appendix E - SSL ScreenSound Synchr
Page 91 and 92:
Appendix F - Status Screen SynchroN
Page 93 and 94:
Appendix G - Index of Controlled Ma
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Index SynchroNet ES/2 User Guide ES
Page 107:
Index SynchroNet ES/2 User Guide si
show all

User Manual - AMS Neve

Create successful ePaper yourself

Delete template?

Save as template?