Cooper B-Line Pipe Hangers & Supports - Dixie Construction Products

More documents

Recommendations

Info

Vibra Trol ® 180 Use: ANH Series Rubber <strong>Hangers</strong> are designed as an economical hanger to dampen noise and vibration in light duty applications. Features: Color-coded insert for load identification. Loads up to 200 Lbs. (2.01 kN) at a .20" (5.1) deflection. Steel pressure plates on top and bottom of insert. Hanging device is 11 gauge cold drawn steel wire that accommodates up to 3 /16" (4.7) rod or bolt attachments. Specify part number and color for desired load. Typical Applications: Suspended ceilings and hot or cold air ducts. 1 1 /4" (31.7) 1" (25.4) 4" (101.6) Vibra Trol For 3 /16" (4.7) Rod ANH Type - Acoustical Vibration Hanger Part Color Rated Load Rated Wt. Each No. Code Lbs. kN Deflection Lbs. kg ANH-20 Red 65 (.29) .20" (5.1) .16 (.07) ANH-40 Black 120 (.53) .20" (5.1) .16 (.07) ANH-70 Blue 200 (.89) .20" (5.1) .16 (.07) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Vibra Trol ® Use: RH Series Neoprene <strong>Hangers</strong> are suggested to dampen noise and minor vibration from suspended high speed equipment (1200 RPM or greater). To be used in-line with all thread rod for single and trapeze type support systems. Features: Color-coded neoprene in-shear insert for load identification. Loads to 2000 Lbs. with deflections to .50" (12.7). RH hangers are available with a 30° rod swing (must specify). Hanger units are shipped assembled. Typical Applications: Suspended mechanical equipment, exhaust fans, ductwork, piping, ceilings, etc. When equipment is suspended from vibration sensitive spans, avoid using RH type hangers. Higher deflection hangers such as the HS and HES series are recommended. Note: Vibration hangers should not come in direct contact with equipment being suspended. 'A' Diameter Hole Top and Bottom for Maximum 'B' Diameter Hanger Rod 'W' 'W/2' 'L/2' 'L' Heavy Duty Hanger Box 'A' Diameter Hole for Maximum 'B' Diameter Hanger Rod Steel Washer 'H' 'F' Double Deflection Neoprene Element 3" (76.2) Dimensions of Neoprene Element Vibra Trol RH Type - Neoprene Vibration Hanger Rated Dimensions in Inches Wt. Part Load Isolator Each No. Lbs. kN Deflection 'L' 'W' 'H' 'F' 'A' 'B' Lbs. kg RHB-Black 60-100 (.27-.44) .50" (12.7) 2 3 /4" 2" 4 1 /2" 2" 3 /4" 5 /8" RHB-Red 100-175 (.44-.78) .50" (12.7) (69.8) (50.8) (114.3) (50.8) (19.0) (15.9) RHC-Green 175-300 (.78-1.33) .50" (12.7) 2 3 /4" 2" 4 1 /2" 2" 3 /4" 5 /8" RHC-Purple 300-700 (1.33-3.11) .50" (12.7) (69.8) (50.8) (114.3) (50.8) (19.0) (15.9) RHD-Yellow 700-1100 (3.11-4.90) .50" (12.7) 3" 2" 7" 2" 3 /4" 5 /8" RHD-Pink 1100-2000 (4.90-8.90) .50" (12.7) (76.2) (50.8) (177.8) (50.8) (19.0) (15.9) 2.0 (.9) 3.0 (1.4) 4.0 (1.8) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. 181
Page 1 and 2:
PH-08 Pipe Hangers & Supports Pipe
Page 3 and 4:
Table of Contents Pictorial Index .
Page 5 and 6:
Pictorial Index PIPE HANGERS Pictor
Page 7 and 8:
Pictorial Index PIPE HANGERS (Conti
Page 9 and 10:
Pictorial Index PIPE SUPPORTS, GUID
Page 11 and 12:
Pictorial Index BRACKETS Pictorial
Page 13 and 14:
Pictorial Index THREADED ACCESSORIE
Page 15 and 16:
Pictorial Index DURA-BLOK (Continue
Page 17 and 18:
Strut Systems Below are some basic
Page 19 and 20:
Technical Data Dura-Copper ® and D
Page 21 and 22:
Technical Data 2. Uninsulated pipes
Page 23 and 24:
Technical Data 2. Continuous concre
Page 25 and 26:
Technical Data E. Support horizonta
Page 27 and 28:
Beam Clamps 'B' 'D' 'C' Setscrew an
Page 29 and 30:
Beam Clamps 'C' 'D' Material: Ducti
Page 31 and 32:
Beam Clamps 7/8" (22.2) Maximum Fla
Page 33 and 34:
Beam Clamps Material: Steel Standar
Page 35 and 36:
Beam Clamps Clamping Rod and Nuts I
Page 37 and 38:
Beam Clamps Material: Steel Steel S
Page 39 and 40:
Beam Clamps Beam Clamps All dimensi
Page 41 and 42:
Pipe Hangers 'A' (Rod Size) Hanger
Page 43 and 44:
Pipe Hangers 'D' 'E' 'A' (Rod Size)
Page 45 and 46:
'D' 'E' B3104CT 'A' (Rod Size) Hang
Page 47 and 48:
Pipe Hangers 'H' Maximum insulation
Page 49 and 50:
Pipe Hangers 'B' 'D' 'A' (Rod Size)
Page 51 and 52:
Pipe Hangers 'B' 'D' 'A' (Rod Size)
Page 53 and 54:
'C' 'A' (Rod Size) Hanger Rod Not I
Page 55 and 56:
Pipe Hangers Bolt and Nut Included
Page 57 and 58:
Pipe Hangers 9/16" (14.3) 2 Holes '
Page 59 and 60:
Pipe Hangers 'D' 'C' 'A' (Rod Size)
Page 61 and 62:
Pipe Hangers Pipe Hangers All dimen
Page 63 and 64:
Pipe Clamps Design Load Bolt Size B
Page 65 and 66:
Pipe Clamps Material: Steel 'A' Bol
Page 67 and 68:
'B' 'C' 'B' 'C' 'A' Bolt Size 'B' C
Page 69 and 70:
'C' Center of pipe to center of cla
Page 71 and 72:
Bolts and Nuts Included Figure B314
Page 73 and 74:
Pipe Clamps Pipe Size Design Load 1
Page 75 and 76:
'E' 'F' 'A' (Rod Size) Hanger Rod N
Page 77 and 78:
'E' 'F' 'D' 'A' (Rod Size) 'C' Figu
Page 79 and 80:
Steel Size 'B' 'A' 'E' 'C' 'D' Bolt
Page 81 and 82:
Pipe Rollers & Roller Supports Mate
Page 83 and 84:
Pipe Rollers & Roller Supports Chan
Page 85 and 86:
Page 87 and 88:
'F' 'A' 'D' 'E' 'C' 'B' 'C' Center
Page 89 and 90:
Pipe Rollers & Roller Supports 'A'
Page 91 and 92:
Page 93 and 94:
Pipe Supports, Guides, Shields & Sa
Page 95 and 96:
Page 97 and 98:
'B' Pipe Size 'C' Center of pipe to
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Insulation Part Thickness Number 1"
Page 127 and 128:
Stock Size 'L' Pipe Supports, Guide
Page 129 and 130:
Page 131 and 132: Concrete Inserts Material: Steel St
Page 133 and 134: Concrete Inserts Material: Malleabl
Page 135 and 136: Concrete Inserts 5/32" (4.0) Dia. N
Page 137 and 138: Concrete Inserts 2 5 /8” (66.7) 1
Page 139 and 140: Concrete Inserts Material: Steel St
Page 141 and 142: Brackets 7 /16" Dia. (11.1) 1" (25.
Page 143 and 144: Brackets Material: Steel (Stainless
Page 145 and 146: Upper Attachments 'B' Overall Heigh
Page 147 and 148: Upper Attachments For #12 Flat Head
Page 149 and 150: Upper Attachments Material: Steel S
Page 155 and 156: Threaded Accessories 'A' (Rod Size)
Page 157 and 158: Threaded Accessories Figure B3188 S
Page 159 and 160: Threaded Accessories 'F' Distance f
Page 161 and 162: 'TL' Specify 'L' 'TL' Threaded Acce
Page 163 and 164: Threaded Accessories Material: Stee
Page 165 and 166: Threaded Accessories 'B' 'A' Dia. M
Page 167 and 168: 'A' Specify 'C' 'A' 'T' Material: S
Page 169 and 170: Threaded Accessories Threaded Acces
Page 171 and 172: Vibra Trol ® Data Selection Distur
Page 173 and 174: 1 1 /2" (38.1) 'L' 'W' 13/16" (20.6
Page 175 and 176: Vibra Trol ® Use: Designed for the
Page 177 and 178: Vibra Trol ® OML*/OM Type - Free S
Page 179 and 180: Vibra Trol ® HMLE*/HME Type - Hous
Page 181: Vibra Trol ® HMLT*/HMT Type - Hous
Page 185 and 186: HSL*/HS Type - Vibration Spring Han
Page 187 and 188: Vibra Trol ® HESL*/HES Type - Comb
Page 189 and 190: Vibra Trol ® SHE Type - Isolation
Page 191 and 192: Vibra Trol ® BVT Series VibraClamp
Page 193 and 194: Vibra Trol ® B1999 Vibra Cushion
Page 195 and 196: Dura-Blok Rooftop Supports Base Onl
Page 197 and 198: Dura-Blok Rooftop Supports DB6 - Se
Page 199 and 200: Dura-Blok Rooftop Supports DBM - Se
Page 201 and 202: Dura-Blok Rooftop Supports DB__DS -
Page 203 and 204: Dura-Blok Rooftop Supports DBR - Se
Page 205 and 206: Dura-Blok Rooftop Supports Compatib
Page 207 and 208: Dura Clean Washdown Supports Dura-C
Page 209 and 210: Dura Clean Washdown Supports Dura-C
Page 211 and 212: Features • Material: 316 Stainles
Page 213 and 214: KwikWire Accessories Installation K
Page 215 and 216: KwikWire Accessories • B-Line Kwi
Page 217 and 218: KwikWire Accessories KwikWire All d
Page 219 and 220: Miscellaneous Assemblies ASSEMBLY 7
Page 229 and 230: ASSEMBLY 66 Miscellaneous Assemblie
Page 233 and 234:
Miscellaneous Assemblies ASSEMBLY 8
Page 235 and 236:
Miscellaneous Assemblies ASSEMBLY 9
Page 237 and 238:
Seismic Assemblies PIPE CLAMP TRANS
Page 239 and 240:
Seismic Assemblies LONGITUDINAL BRA
Page 241 and 242:
Reference Data - Metric Conversion
Page 243 and 244:
Reference Data AWWA DUCTILE IRON PI
Page 245 and 246:
Reference Data COPPER TUBING (TYPE
Page 247 and 248:
Reference Data SCHEDULE 40 PVC PLAS
Page 249 and 250:
Reference Data AMERICAN STANDARD 'S
Page 251 and 252:
Reference Data WIDE FLANGE I-BEAMS
Page 253 and 254:
FEDERAL SPECIFICATION TO B-LINE & M
Page 255 and 256:
Reference Data B-LINE COMPLIANCES &
Page 257 and 258:
Index Part No. Page Part No. Page P
Page 260:
Other Cooper B-Line Product Lines C
show all

Cooper B-Line Pipe Hangers & Supports - Dixie Construction Products

Create successful ePaper yourself

Delete template?

Save as template?