Download - TDK-Lambda

More documents

Recommendations

Info

Specifications Genesys GEN / GENH 750 / 1500 W Interface RS-232 & RS-485 or Optional GPIB / LAN Interface Model 6 8 12.5 20 Remote Current Programming (16 bit) (750 W) Resolution (0.012 % of lo Rated) [mA] 12 10.8 7.2 4.56 Accuracy (0.1 % lo Rated + 0.1 % of lo Actual Output) [mA] 200 180 120 76 Readback Current (750 W) Resolution (0.012 % of lo Rated) [mA] 12 10.8 7.2 4.56 Accuracy (0.3 % lo Rated + 0.1 % of lo Actual Output) [mA] 400 360 240 152 Remote Current Programming (16 bit) (1500 W) Resolution (0.012 % of lo Rated) [mA] 24 21.6 14.4 9.12 Accuracy (0.1 % lo Rated + 0.1 % of lo Actual Output) [mA] 400 360 240 152 Readback Current (1500 W) Resolution (0.012 % of lo Rated) [mA] 24 21.6 14.4 9.12 Accuracy (0.3 % lo Rated + 0.1 % of lo Actual Output) [mA] 800 720 480 304 Remote Voltage Programming (16 bit) (750/1500 W) Resolution (0.012 % of Vo Rated) [mV] 0.72 0.96 1.50 2.40 Accuracy (0.05 % Vo Rated + 0.05 % of Vo Actual Output) [mV] 6.0 8.0 12.5 20 Readback Voltage (750/1500 W) Resolution (0.012 % of Vo Rated) [mV] 0.72 0.96 1.50 2.40 Accuracy (0.1 % Vo Rated + 0.1 % of Vo Actual Output) [mV] 12 16 25 40 OVP/UVL Programming (750 W/1500 W) Resolution (0.1 % of Vo Rated) [mV] 6 8 12 20 Accuracy (1 % of Vo Rated) [mV] 60 80 125 200 Analog Programming and Monitoring (750 W/1500 W) Vout Voltage Programming Iout Voltage Programming Vout Resistor Programming Iout Resistor Programming On/Off control (rear panel) Output current monitor Output voltage monitor Power supply OK signal CV/CC indicator Enable/Disable Local/Remote analog control Local/Remote analog control indicator 0~100 %, 0~5 V or 0~10 V, user-selectable. Accuracy and linearity: ± 0.5 % of rated Vout. 0~100 %, 0~5 V or 0~10 V, user-selectable. Accuracy and linearity: ± 1 % of rated lout. 0~100 %, 0~5/10 kΩ full scale, user-selectable. Accuracy and linearity: ± 1 % of rated Vout. 0~100 %, 0~5/10 kΩ full scale, user-selectable. Accuracy and linearity: ± 1.5 % of rated lout. By electrical. Voltage: 0~0.6 V/2~15 V, or dry contact, user-selectable logic 0~5 V or 0~10 V, accuracy: 1 %, user-selectable 0~5 V or 0~10 V, accuracy: 1 %, user-selectable TTL high (4~5 V) -OK, 0 V-Fail 500 series resistance CV: TTL high (4~5 V), CC: TTL low (0~0.6 V), maximum Voltage: 30 V, sink current: 10 mA Dry contact. Open: off, Short: on. Max. voltage at Enable/Disable in: 6 V By electrical signal (TTL) or Open/Short: 0~0.6 V or short: Remote, 4~5 V or open: Local Open collector, Local: Open, Remote: On. Maximum voltage: 30 V, maximum sink current: 5 mA 34
30 40 50 60 80 100 150 300 600 3.0 2.28 1.50 1.14 0.90 0.60 0.30 0.16 50 38 25 19 15 10 5.0 2.6 3.0 2.28 1.50 1.14 0.90 0.60 0.30 0.16 100 76 50 38 30 20 10 5.2 6.0 4.56 3.60 3.0 2.28 1.80 1.20 0.60 0.32 100 76 60 50 38 30 20 10 5.2 6 4.56 3.60 3.0 2.28 1.80 1.20 0.60 0.32 200 152 120 100 76 60 40 20 10.4 3.60 4.80 6 7.2 9.6 12 18 36 72 30 40 50 60 80 100 150 300 600 3.60 4.80 6.0 7.2 9.6 12 18 36 72 60 80 100 120 160 200 300 600 1200 30 40 50 60 80 100 150 300 600 300 400 500 600 800 1000 1500 3000 6000 Front Panel (750 W/1500 W) Control functions Display Indications Input Characteristics Input voltage/freq. (*1) Power Factor EN61000-3-2,3 compliance Vout/lout manual adjust by separate encoders (coarse and fine adjustment selectable) OVP/UVL manual adjust by Volt. Adjust encoder AC on/off, Output on/off, Re-start modes (auto, safe), Fold-back control (CV to CC), Go to local control Address selection by Voltage (or current) adjust encoder. Number of addresses: 31 RS232/485 and IEEE488.2 selection by IEEE enable switch and DIP switch Baud rate selection: 1200, 2400, 4800, 9600 and 19200 Voltage 4 digits, accuracy: 0.5 % ±1 count Current 4 digits, accuracy: 0.5 % ±1 count Voltage, Current, Alarm, Fine, Preview, Fold-back, Local, Output On, Front Panel Lock 85~265 V AC continuous, 47~63 Hz, Single-Phase 0.99 @100/200 V AC, rated output power Complies with EN61000-3-2 class A and EN61000-3-3 at 20~100 % output power Input current 100/200 V AC 10.5 A / 5 A (750 W), 21 A / 11 A (1500 W) Inrush current 100/200 V AC Less than 25 A (750 W), Less than 50 A (1500 W) Hold-up time More than 20 ms, 100 V AC, at 100 % load *1: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be described as 100-240 V AC (50/60 Hz). Sequel } 35
Page 1 and 2: Programmable Power Supplies EN Inno
Page 3 and 4: Many applications require more than
Page 5 and 6: Sequence programming Applications:
Page 7 and 8: Front panel description Z + 200 / 4
Page 9 and 10: Specifications Z + 200 W Output Rat
Page 11 and 12: Model Z 10-20 20-10 36-6 60-3.5 100
Page 13 and 14: Analog Programming and Monitoring 1
Page 15 and 16: Specifications Z + 600 W Output Rat
Page 17 and 18: Model Z 10-60 20-30 36-18 60-10 100
Page 19 and 20: Analog Programming and Monitoring 1
Page 21 and 22: Outline drawings Z + 200 / 400 / 60
Page 23 and 24: Z + Standard Configurations Benchto
Page 25 and 26: 19” Rack Mounted to 4.8 kW P/N: Z
Page 27 and 28: Features • High Power Density 750
Page 29 and 30: Front panel description GENH 750 W
Page 31 and 32: Front panel description GEN 750/150
Page 33: 30-25 40-19 60-12.5 80-9.5 100-7.5
Page 37 and 38: Mechanical Construction GEN 750 W/1
Page 39 and 40: - + I REVERSE I 0 PWM Motor Source
Page 41 and 42: GEN20-38 PSINK GEN30-25 PSINK GEN40
Page 47 and 48: Outline drawings Genesys GEN 750 /
Page 49 and 50: Front panel description GEN 2400 W
Page 51 and 52: 20-120 30-80 40-60 60-40 80-30 100-
Page 53 and 54: 20-165 30-110 40-85 60-55 80-42 100
Page 55 and 56: 20-120 30-80 40-60 60-40 80-30 100-
Page 58 and 59: Genesys GEN 3.3 kW in 2 U 19” rac
Page 60 and 61: Specifications Genesys GEN 3.3 kW M
Page 62 and 63: Interface RS-232 & RS-485 or Option
Page 64 and 65: Input Characteristics GEN 8-400 10-
Page 66 and 67: Outline drawings Genesys GEN 3.3 kW
Page 68 and 69: Genesys GEN 5 kW in 2 U 19” rack
Page 70 and 71: Specifications Genesys GEN 5 kW Mod
Page 72 and 73: Protective Functions GEN 8-600 10-5
Page 74 and 75: Input Characteristics GEN 8-600 10-
Page 76 and 77: Outline drawings Genesys GEN 5 kW U
Page 78 and 79: NEW Genesys GEN 3.3 / 5 kW with Fas
Page 80 and 81: Genesys GEN 10 / 15 kW in 3U 19”
Page 82 and 83: Specifications Genesys GEN 10 / 15
Page 84 and 85:
Protective Functions OCP [%] 0~100
Page 86 and 87:
EMC 208 V input models CE Mark ESD
Page 88 and 89:
Genesys Standard Configurations Rac
Page 90 and 91:
Genesys LAN 2.0 Interface NEW The o
Page 92 and 93:
Genesys Accessories Communication C
Page 94 and 95:
ZUP 200 / 400 / 800 W The Zero-up s
Page 96 and 97:
Specifications ZUP Series Model ZUP
Page 98 and 99:
Model ZUP 6-33 6-66 6-132 10-20 10-
Page 100 and 101:
GP485A The GP485A GPIB RS485 Contro
Page 102 and 103:
Outline drawings ZUP 800 W Units Di
Page 104 and 105:
ZUP Standard Configurations Benchto
Page 106 and 107:
ZUP Options 200 / 400 / 800 W Model
Page 108:
Please contact your local sales off
show all

Download - TDK-Lambda

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?