Download - TDK-Lambda

More documents

Recommendations

Info

Interface RS-232 & RS-485 or Optional GPIB / LAN Interface GEN 8-400 10-330 15-220 Model [V] 8 10 15 Remote Current Programming (16 bit) Resolution (0.012 % of lo Rated) [mA] 48 39.6 26.4 Accuracy (0.2 % of lo Rated + 0.1 % of lo Actual Output) (*10) [mA] 1200 990 660 Readback Current Resolution (0.012 % of lo Rated) [mA] 48 39.6 26.4 Accuracy (0.3 % of lo Rated + 0.1 % of lo Actual Output) (*10) [mA] 1600 1320 880 Remote Voltage Programming (16 bit) Resolution (0.012 % of Vo Rated) [mV] 0.96 1.2 1.8 Accuracy (0.05 % Vo Rated + 0.05 % of Vo Actual Output) [mV] 8 10 15 Readback Voltage Resolution (0.012 % of Vo Rated) [mV] 0.96 1.2 1.8 Accuracy (0.1 % Vo Rated + 0.1 % of Vo Actual Output) [mV] 16 20 30 OVP/UVL Programming Resolution (0.1 % of Vo Rated) [mV] 8 10 15 Accuracy (1 % of Vo Rated) [mV] 80 100 150 Analog Programming and Monitoring Vout Voltage Programming Iout Voltage Programming (*10) Vout Resistor Programming Iout Resistor Programming (*10) On/Off control (rear panel) Output current monitor (*10) Output voltage monitor Power supply OK signal CV/CC indicator 0~100 %, 0~5 V or 0~10 V, user-selectable. Accuracy and linearity: ± 0.5 % of rated Vout. 0~100 %, 0~5 V or 0~10 V, user-selectable. Accuracy and linearity: ± 1 % of rated lout. 0~100 %, 0~5/10 kΩ full scale, user-selectable. Accuracy and linearity: ± 1 % of rated Vout. 0~100 %, 0~5/10 kΩ full scale, user-selectable. Accuracy and linearity: ± 1.5 % of rated lout. By electrical. Voltage: 0~0.6 V/2~15 V, or dry contact, user-selectable logic 0~5 V or 0~10 V, accuracy: ± 1 %, user-selectable 0~5 V or 0~10 V, accuracy: ± 1 %, user-selectable TTL high (2~15 V) -OK, 0 V-Fail 500 Ω series resistance Open collector. CC mode: On, CV mode: Off. Maximum voltage: 30 V, maximum sink current: 10 mA. Enable/Disable Dry contact. Open: off, Short: on. Max. voltage at Enable/Disable in: 6 V Local/Remote analog control By electrical signal or Open/Short: 0~0.6 V or short: Remote, 2~15 V or open: Local Local/Remote analog control indicator Open collector, Local: Open, Remote: On. Maximum voltage: 30 V, maximum sink current: 10 mA *10: The Constant Current programming readback and monitoring accuracy does not include the warm-up and Load regulation thermal drift. 62
20-165 30-110 40-85 60-55 80-42 100-33 150-22 200-16.5 300-11 600-5.5 20 30 40 60 80 100 150 200 300 600 19.8 13.2 10.2 6.6 5.0 4.0 2.6 2.0 1.3 0.7 495 330 255 165 126 99 66 49.5 33 16.5 19.8 13.2 10.2 6.6 5.0 4.0 2.6 2.0 1.3 0.7 660 440 340 220 168 132 88 49.5 44 22 2.4 3.6 4.8 7.2 9.6 12 18 24 36 72 20 30 40 60 80 100 150 200 300 600 2.4 3.6 4.8 7.2 9.6 12 18 24 36 72 40 60 80 120 160 200 300 400 600 1200 20 30 40 60 80 100 150 200 300 600 200 300 400 600 800 1000 1500 2000 3000 6000 Front Panel Control functions Display Indications Vout/lout manual adjust by separate encoders (coarse and fine adjustment selectable) OVP/UVL manual adjust by Volt. Adjust encoder AC on/off, Output on/off, Re-start modes (auto, safe), Fold-back control (CV to CC), Go to local control Address selection by Voltage (or current) adjust encoder. Number of addresses: 31 Re-start modes (automatic re-start, safe mode) Baud rate selection: 1200, 2400, 4800, 9600 and 19200 Voltage: 4 digits, Accuracy: 0.5 % of rated output voltage ±1 count Current: 4 digits, Accuracy: 0.5 % of rated output current ±1 count Voltage, Current, Alarm, Fine, Preview, Fold-back, Local, Output On, Front Panel Lock, CV/CC 63
Page 1 and 2:
Programmable Power Supplies EN Inno
Page 3 and 4:
Many applications require more than
Page 5 and 6:
Sequence programming Applications:
Page 7 and 8:
Front panel description Z + 200 / 4
Page 9 and 10:
Specifications Z + 200 W Output Rat
Page 11 and 12: Model Z 10-20 20-10 36-6 60-3.5 100
Page 13 and 14: Analog Programming and Monitoring 1
Page 15 and 16: Specifications Z + 600 W Output Rat
Page 17 and 18: Model Z 10-60 20-30 36-18 60-10 100
Page 19 and 20: Analog Programming and Monitoring 1
Page 21 and 22: Outline drawings Z + 200 / 400 / 60
Page 23 and 24: Z + Standard Configurations Benchto
Page 25 and 26: 19” Rack Mounted to 4.8 kW P/N: Z
Page 27 and 28: Features • High Power Density 750
Page 29 and 30: Front panel description GENH 750 W
Page 31 and 32: Front panel description GEN 750/150
Page 33 and 34: 30-25 40-19 60-12.5 80-9.5 100-7.5
Page 35 and 36: 30 40 50 60 80 100 150 300 600 3.0
Page 37 and 38: Mechanical Construction GEN 750 W/1
Page 39 and 40: - + I REVERSE I 0 PWM Motor Source
Page 41 and 42: GEN20-38 PSINK GEN30-25 PSINK GEN40
Page 47 and 48: Outline drawings Genesys GEN 750 /
Page 49 and 50: Front panel description GEN 2400 W
Page 51 and 52: 20-120 30-80 40-60 60-40 80-30 100-
Page 53 and 54: 20-165 30-110 40-85 60-55 80-42 100
Page 55 and 56: 20-120 30-80 40-60 60-40 80-30 100-
Page 58 and 59: Genesys GEN 3.3 kW in 2 U 19” rac
Page 60 and 61: Specifications Genesys GEN 3.3 kW M
Page 64 and 65: Input Characteristics GEN 8-400 10-
Page 66 and 67: Outline drawings Genesys GEN 3.3 kW
Page 68 and 69: Genesys GEN 5 kW in 2 U 19” rack
Page 70 and 71: Specifications Genesys GEN 5 kW Mod
Page 72 and 73: Protective Functions GEN 8-600 10-5
Page 74 and 75: Input Characteristics GEN 8-600 10-
Page 76 and 77: Outline drawings Genesys GEN 5 kW U
Page 78 and 79: NEW Genesys GEN 3.3 / 5 kW with Fas
Page 80 and 81: Genesys GEN 10 / 15 kW in 3U 19”
Page 82 and 83: Specifications Genesys GEN 10 / 15
Page 84 and 85: Protective Functions OCP [%] 0~100
Page 86 and 87: EMC 208 V input models CE Mark ESD
Page 88 and 89: Genesys Standard Configurations Rac
Page 90 and 91: Genesys LAN 2.0 Interface NEW The o
Page 92 and 93: Genesys Accessories Communication C
Page 94 and 95: ZUP 200 / 400 / 800 W The Zero-up s
Page 96 and 97: Specifications ZUP Series Model ZUP
Page 98 and 99: Model ZUP 6-33 6-66 6-132 10-20 10-
Page 100 and 101: GP485A The GP485A GPIB RS485 Contro
Page 102 and 103: Outline drawings ZUP 800 W Units Di
Page 104 and 105: ZUP Standard Configurations Benchto
Page 106 and 107: ZUP Options 200 / 400 / 800 W Model
Page 108: Please contact your local sales off
show all

Download - TDK-Lambda

Create successful ePaper yourself

Delete template?

Save as template?