SuperSweep64 - dirac

More documents

Recommendations

Info

$Guide to Imfufa LaTeX - dirac$

Connect the Coil-Drive Cable Note: The white wire must be connected to the positive (+) terminal for the longitudinal coil, and the green wire must be connected to the negative (-) terminal for the longitudinal coil. 7. Attach the lugs on the ends of the red-black wire pair to the feedthrough terminals for the lateral position coil. 8. Plug the other end of the cable into rear panel connector J2 on the programmable sweep chassis and tighten the twistlock. Temescal SuperSweep 6/6/02 19
Installation 110/220-VAC Power The sweep is configured for 110/220 VAC input power. Sweep Interface Cable (See Figure 2-2 for I/Os.) Coil Drive Cable From J2 Pins Ground Copper Strap Connect to vacuum cubicle’s central grounding point, which must be connected to a low-impedance ground. For instructions on setting up the low-impedance ground, see Figure 2-1 of the Simba TM Power Supply Manual. 4 5 1 2 Green White Red Black - + + - } } To gun longitudinal coil To gun latitudinal coil Figure 2-1. Rear Panel Connections 20 6/6/02 Temescal SuperSweep
Page 1 and 2: SuperSweep64 Instruction Manual con
Page 3 and 4: SuperSweep TM 64 Instruction Manual
Page 5 and 6: Summary of Terms and Conditions of
Page 7 and 8: Safety Instructions for Operating a
Page 9 and 10: Special Amendment for United Kingdo
Page 11 and 12: Health Hazard The condensates depos
Page 13 and 14: Standard Wave . . . . . . . . . . .
Page 15 and 16: To Use the PC Handheld Controls . .
Page 17 and 18: Overview A total of 16 (4 x 4) wave
Page 19 and 20: Overview Emission Current Control S
Page 21 and 22: Overview Recipe Window • create a
Page 23 and 24: Overview Arbitrary Wave Standard Wa
Page 25 and 26: Overview Standard Wave For a Standa
Page 27 and 28: Overview Position Limits Position L
Page 29 and 30: Overview The program generates 1,02
Page 31 and 32: Overview After drawing the pattern,
Page 33: Installation Connect the Coil-Drive
Page 37 and 38: Installation Figure 2-2. Remote I/O
Page 39 and 40: Installation Table 2. Remote I/Os I
Page 41 and 42: Installation • Remove the three j
Page 43 and 44: Installation Setting the Position I
Page 45 and 46: Installation 14. Rotate the Adjust
Page 47 and 48: Installation • latitude position,
Page 49 and 50: Features and Functions ➹ Redraw a
Page 51 and 52: Features and Functions Longitudinal
Page 53 and 54: Features and Functions Table 1. SS6
Page 55 and 56: Features and Functions PC Menu Feat
Page 57 and 58: Features and Functions 2. Using a 9
Page 59 and 60: Features and Functions 6. If the co
Page 61 and 62: Features and Functions 5. Select OK
Page 63 and 64: Features and Functions See Setting
Page 65 and 66: Features and Functions 1. From the
Page 67 and 68: Features and Functions 9. The resul
Page 69 and 70: Features and Functions Using Redraw
Page 71 and 72: Features and Functions Set Dwell Fa
Page 73 and 74: Features and Functions How It Works
Page 75 and 76: Features and Functions 3. Edit the
Page 77 and 78: Features and Functions 1. From the
Page 79 and 80: Features and Functions Control the
Page 81 and 82: Features and Functions To disable/e
Page 83 and 84: Features and Functions 2. Load a Re
Page 85 and 86:
Features and Functions 70 6/6/02 Te
Page 87 and 88:
Theory of Operation The sweep contr
Page 89 and 90:
Theory of Operation amplifiers U21A
Page 91 and 92:
multiple SS64 connections 37 N netw
show all

SuperSweep64 - dirac

Create successful ePaper yourself

Delete template?

Save as template?