ADDENDUM NO. 1 - STV Group, Inc.

ADDENDUM NO. 1 

September 20, 2012 

QUEENS COLLEGE CONVERSION OF LABORATORIES 

CONTRACT NO. CITYWCUCF010904GC – General Construction 

CONTRACT NO. CITYWCUCF010904MECH – Mechanical 

CONTRACT NO. CITYWCUCF010904EL Electrical 

CONTRACT NO. CITYWCUCF010904PL Plumbing 

This Addendum is being issued for the purpose of amending the subject Request for Bids (RFBs) as below and 

is hereby made part of said RFBs to the same extent as though it were originally included therein. This 

Addendum makes the following changes and clarifications to the bid documents: 

Changes to Bid Documents 

(1) Project Manual Table of Contents 

a. Volume 1 of 2 – Change “Envelope #3 – Low Bidders’ Additional Information Forms” to 

“Envelope #2 – Low Bidders’ Additional Information Forms” 

(2) Section II, Article 5.4 of the Instructions to Bidders – Prevailing Wage Rate/ Craft Training Program 

a. Replace Article 5.4 in its entirety with the following: “If an apprentice is employed on the 

project, they must be registered under a bona fide New York State Department of Labor 

Apprenticeship Program in accordance with New York State Labor Law 220.3.” 

(3) Section 01 11 16 – Summary of Work 

a. Page 011116>2 Item E – Add sentence: “In the event of a jurisdictional work issue for a prime 

contractor or subcontractor to a prime contractor, the other three prime contractors will be 

responsible for providing all labor as necessary to maintain labor harmony.” 

(4) Project Milestone Schedule 

a. Change Construction Phase Duration from “170 ccd” to “165 ccd” 

(5) Price Proposal for Electrical Contract 

a. Price Proposal for Electrical Contract shall be replaced with Attachment No. 1: Revised Price 

Proposal for Electrical Contract 

(6) Section 01 11 17 of the General Requirements shall be replaced with Attachment No. 2: Revised Section 

01 11 17 – Drawing List 

(7) Drawing G>001.00 shall be replaced with Attachment No. 3: Revised Drawing G>001.00 dated 9>13>12 

(8) Drawing A>100.00 shall be replaced with Attachment No. 4: Revised Drawing A>100.00 dated 9>13>12 


Page 1 of 6





(14) Drawing FP>001.00 shall be replaced with Attachment No.10: Revised Drawing FP>001.00 dated 9>13>12 

(15) Drawing FP>101.00 shall be replaced with Attachment No.11: Revised Drawing FP>101.00 dated 9>13>12 

(16) Drawing P>001.00 shall be replaced with Attachment No.12: Revised Drawing P>001.00 dated 9>13>12 

(17) Drawing M>101.00 shall be replaced with Attachment No.13: Revised Drawing M>101.00 dated 9>13>12 

(18) Drawing E>001.00 shall be replaced with Attachment No.14: Revised Drawing E>001.00 dated 9>13>12 






(24) Drawing FA>001.00 shall be replaced with Attachment No.20: Revised Drawing FA>001.00 dated 9>13>12 

Bidder Questions and Reponses 

Question (1): Regarding M/WBE Requirements – Do we choose who we are giving the work? Do we give the 

% of work to either MBE or WBE, or is it mandatory to give 20% to both MBE and WBE? 

Answer (1): Refer to Section III, Article 2 of the Instructions to Bidders for information regarding 

participation by Minority>Owned and Women>Owned Business Enterprises. The Bidder is 

required to meet the requirements for participation by New York State Certified Minority>Owned 

Business Enterprises (MBE) at 12.00% of the total contract value, and Women>Owned Business 

Enterprises (WBE) at 8.00% of the total contract value. Additional information regarding 

M/WBE participation can be found in Appendix 2 of the Instructions to Bidders, with a link to the 

directory of New York State Certified MWBEs (http://www.esd.ny.gov/mwbe.html). Bidders are 

required to select proposed subcontractors for participation in the MWBE program associated 

with this project. 

Question (2): Drawing G001.00 states to maintain negative air pressure during construction. Is this for the 

entire duration of project? 

Answer (2): 

The GC is required to maintain negative air pressure for the entire duration of the project, 

through Substantial Completion. 

Question (3): Is there a specific on or off campus location where STV trailer can be located? 

Answer (3): 

There is no space available on campus for the STV office trailer. Contractor is required to locate 

trailer off campus in close proximity to the project site. 

STV Construction, Inc. 

Addendum No. 1 (09>20>12) Page 2 of 6 

CITYW>CUCF>01>09>04>GC/MECH/EL/PL

Question (4): Drawing A100.00 – Demo note #3 states to discard and or salvage existing equipment. For 

bidding purposes can you specify which pieces get discarded and which pieces get salvaged? 

Answer (4): 

Equipment to be salvaged will be identified prior to start of demolition. Contractor to include 

cost of removal and disposal and/or removal and salvage as part of Total Bid Price. Salvage 

includes removal and turn>over to college at a storage location on the Queens College campus as 

designated by the college. 

Question (5): Drawing A100.00 – Demo note #4 states to remove VCT floor and base. Is this at all rooms that 

have existing VCT and base? 

Answer (5): 

The existing VCT and base, including mastic and adhesive, in all labs and prep rooms within the 

scope of work for this project shall be removed (Rooms B237, B241, B243, B245, B203, B211, 

D231, and D231A). 

Question (6): Is shot blasting of floors required prior to resinous flooring application? And does it have to be 

done after hours? 

Answer (6): 

Shot blasting is required for the preparation of concrete substrates to receive resinous flooring. 

See Section 096723 of the Contract Specifications for further details regarding the installation of 

resinous flooring. Preparation work and application of resinous flooring shall be performed after 

normal work hours. There is no additional compensation for after hours work. See Section 

011116 of the Contract General Conditions for further details regarding work restrictions. 

Question (7): Drawing A100.00 Note 10 states to remove existing blackboards. Please provide quantity. 

Answer (7): 

Drawing A100.00 Note 10 has been revised to include removal of all existing blackboards and 

whiteboards. Quantity to be verified in field by Contractor. 

Question (8): Drawing A110.00/ P601.00 – Which prime provides emergency shower/eyewash? 

Answer (8): 

The Plumbing Contractor shall furnish and install the combination emergency shower eye/ face 

wash units and the deck mounted hand held emergency eye/ face wash units. See Dwg. P>501.00 

and Specification Section 224500 (Emergency Plumbing Fixtures) for further information. 


Note the following regarding Laboratory Fixtures: 

• Plumbing Contractor furnishes and installs Weldbilt Double Compartment Scullery Sink and 

associated faucet (Spec Section 224300>2.03) in Rm D231. All epoxy resin sinks (Spec 

Section 123553>2.08) are furnished and installed by General Contractor. Associated faucets 

for epoxy resin sinks are furnished by General Contractor and installed by Plumbing 

Contractor. Air, vacuum and gas turrets are furnished by General Contractor and installed by 

Plumbing Contractor. 

• Electrical pedestals housing for laboratory casework shall be furnished by General 

Contractor and installed by Electrical Contractor. 



• The installation contractor is responsible for accepting delivery and storage of material 

furnished by other contractor(s), in accordance with the requirements of the contract. The 

installation contractor must furnish and install all ancillary components to provide complete 

installation for proper operation of equipment and material. 

Question (9): Who furnishes and installs smart boards? 

Answer (9): 

Smart boards shall be furnished and installed by the Electrical Contractor. See Specialty 

Equipment Schedule on Drawings A>401.00, A>402.00, A>403.00, A>404.00, and A>407.00. 

Question (10): Spec Section 013529 Note 11 – Does GC provide watchmen service? 

Answer (10): The General Contractor shall provide security services for the STV Construction Field Office 

and Equipment. The General Contractor is also responsible for the security of the work site and 

to provide suitable site protection to prevent unauthorized entry onto the site, until final 

acceptance by CUNY, in accordance with contract requirements. 

Question (11): Spec Section 015100>2E – Where can we place temp toilets? 

Answer (11): Queens College will provide an area on campus outside the Science Building for the General 

Contractor to locate temporary toilets. 

Question (12): Spec Sect 05100>3H – Is temp fence required? 

Answer (12): Temporary fencing is not required. 

Question (13): Spec Sect 011116>11 2.2 a>1 calls for temp barricades. Please provide locations where these 

barricades are to be constructed. 

Answer (13): Temporary construction barricades are required in the corridors adjacent to the entrances of the 

laboratories within the scope of work for this project. General Contractor shall comply with 

Section 011116 of the General Requirements for design of the temporary construction barricade. 

Question (14): Spec Sect 011116>9 1.9 – Note 9 calls for masonite protection of floors. Can this protection be 

left in place or must it be picked up and reinstalled on daily basis? 

Answer (14): The General Contractor is permitted to leave protection in place as long as it is maintained on a 

daily basis, presents no tripping hazard, and does not obstruct doors or create any type of access 

issues, in accordance with the contract General Requirements. 




Question (15): Is the existing fire alarm system approved by the fire department? 

Answer (15): An allowance of $25,000.00 has been included in the Revised Electrical Price Proposal for work 

performed by the Electrical Contractor directly related to correction of non>compliance issues for 

the existing Fire Alarm System in the Queens College Science Building. All costs to be verified. 

Question (16): Who will be responsible to file the application for plan examination for the additional panel and 

devices related to the fire alarm system? 

Answer (16): STV has filed the application for plan examination for the additional fire alarm panel and 

devices. 

Question (17): Who is responsible for the design of the new fire alarm system? 

Answer (17): STV has developed the design of the new fire alarm system as specified in the Contract 

Documents. 

Question (18): If the fire department requires additional coverage, who will be responsible for the additional 

cost? 

Answer (18): FDNY requirement for additional coverage exceeding the contract design documents shall be 

processed as a change order to the electrical base contract. 

Question (19): Drawing FA>001.00 General Note #12 reads “Electrical Contractor shall verify operation of 

existing fire alarm pull stations throughout the building for possible replacement.” Can you 

please provide count of how many pull stations are in the building? 

Answer (19): Attachment No. 21 – Fire Alarm System Pull Station Code Card is included in this Addendum 

for your use in determining the existing pull stations throughout the Queens College Science 

Building. 

Question (20): Who is responsible for the replacement of any non>functioning pull stations? 

Answer (20): The Electrical Contractor is responsible for replacement of any non>functioning pull stations, 

under the Allowance for work performed by the Electrical Contractor directly related to 

correction of non>compliance issues for the existing Fire Alarm System. 

Question (21): Drawing E>600.00 note regarding the existing distribution panel reads “…Replace existing 

overcurrent device(s) previously serving removed panel(s) with new compatible 200A, 3P + N 

overcurrent device (typical).” Who is responsible to verify that existing overcurrent devices 

service only the mentioned panels? 

Answer (21): The Electrical Contractor is responsible to verify that existing overcurrent devices service only 

the mentioned panels, as part of base contract work. 




Question (22): In the event that the overcurrent devices service additional load not within the working space, 

who is responsible for the temporary power to the additional load? 

Answer (22): The Electrical Contractor is responsible for the temporary power to the additional load. The 

contractor’s cost to provide temporary power to the additional load will be processed as a change 

order for extra work. 

Question (23): Since we were not able to see the distribution panels, can you please provide existing distribution 

panel manufacturer and model number also the type of breaker required. 

Answer (23): Attachment No. 22 – Nameplate Data for Existing Distribution Panels and Attachment No. 23 – 

Nameplate Data for Existing Panelboard Units are included in this Addendum for your use. 

Question (24): Please provide approximate distance between existing distribution panels and new panels located 

inside the labs. 

Answer (24): Attachment No. 24 – CUNY QC SB 1 st Floor Directory, Attachment No. 25 – CUNY QC SB 2 nd 

Floor Directory, and Attachment No. 26 – CUNY QC SB 3 rd Floor Directory are included in this 

Addendum for your use in determining the distance between existing distribution panels and new 

panels located inside labs. Locations of existing distribution panels are indicated in Part Power 

Riser Diagram – New, on Drawing E>600.00. 

By signing in the space provided below, the Proposer acknowledges receipt of this Addendum. This 

Addendum must be signed by the Proposer and submitted with the Proposal. 

________________________ 

Name of Proposer 

________________________ ____________________ ____________________________ ____________ 

Name of Authorized Proposer Title Signature Date 

Representative 




ATTACHMENT NO. 1 

REVISED PRICE PROPOSAL FOR ELECTRICAL 

CONTRACT 

CITYWCUCF010904EL 


Addendum No. 1 (092012) 

CITYWCUCF010904GC/MECH/EL/PL

PRICE PROPOSAL – ENVELOPE 1 

PRICE PROPOSAL SUBMISSION 

for 

LUMP SUM BID 

to 

STV CONSTRUCTION, INC. 

for the following: 

Contract Number: 

CITYWCUCF010904EL 

Contract Name/ Description: Science Building – 2 nd Floor Conversion of Laboratories – 

Electrical Contractor 

College: 

Borough: 

Queens College__________________________________ 

Queens_________________________________________ 

Bid 

of 

______________________________________________________________________________ 

(Bidder’s Name) (Bidder’s Federal I.D. #) 

a corporation organized and existing under the laws of the State of 

or a limited liability company organized and existing under the laws of the State of 

or a partnership or joint venture consisting of 

A. Price Proposal Submission: 

The Bidder shall complete and execute this Price Proposal Form and enclose it in a sealed and 

clearly marked and properly identified envelope with all other required bid documents. 

The bidder must submit its sealed Price Proposal to STV Construction, Inc. in accordance with 

the terms listed in the Instruction to Bidders or modified by Addendum. See Instructions to 

Bidders and all Contract documents. 

65


B. Time is of the essence for completion of the project in this package. 

C. Price 

1. The undersigned, as Bidder, declares: 

• That this Price Proposal is made, without collusion with any other person, firm or 

corporation; 

• That the bidder has carefully examined the form of the Project Manual, Advertisement / 

Request for Bids, Contract / Form of Contract, Instructions to Bidders, Addenda, 

Specifications, Plans and all other Contract Documents; 

• That the Bidder has carefully examined the locations, conditions and classes of material 

for the proposed work; and 

• That the bidder agrees that it will provide all necessary machinery, tools, apparatus and 

other means of construction and will do all work and furnish all the materials called for 

in the Contract Documents in the manner therein prescribed. 

2. In submitting this Price Proposal, the Bidder agrees: 

• That STV Construction, Inc., and/or CUNY and/or CUCF has the right to reject this 

Price Proposal in accordance with the Instructions to Bidders. 

• To hold this Price Proposal open for a period of one9hundred9twenty (120) calendar 

days from the date of the public opening and reading of the Price Proposals, unless this 

time period is extended by mutual agreement of the Bidder and STV Construction, Inc. 

• To accomplish the work at the price bid, in accordance with the Contract Documents. 

3. Total Price: 

Total amount for the furnishing of all labor, materials, services, and equipment required in 

conjunction with and properly incidental to all work, in conformance with all Contract 

Documents. 

In case of a discrepancy between the amount shown in words and the amount shown in 

figures, the amount shown in words shall govern. 

THE PUBLIC OPENING AND READING OF PRICE IS FOR INFORMATIONAL 

PURPOSES ONLY AND IS NOT TO BE CONSTRUED AS AN ACCEPTANCE OR 

REJECTION OF ANY BID SUBMITTED. 

66


TOTAL 

PRICE:__________________________________________________________________ 

(In Words) 

$___________________________________________________________ 

(In Figures) 

D. WORK COST BREAKDOWN 

The attached Work Cost Breakdown Form shall be filled out and submitted by the Contractor. 

The Total must equal the Total Price, under Section C.3. of this Price Proposal Submission. 

FAILURE TO COMPLETE THE WORK COST BREAKDOWN MAY RESULT IN 

DISQUALIFICATION OF THE BID. 

E. ALLOWANCE FOR FIRE ALARM SYSTEM COMPLIANCE WORK 

The Total Price shall include an allowance of $25,000.00 for work performed by the Electrical 

Contractor directly related to correction of non9compliance issues for the existing Fire Alarm System in 

the Queens College Science Building. All costs associated with the Fire Alarm System Allowance work 

to be verified. 

67


QUEENS COLLEGE SCIENCE BUILDING – 2 ND FLOOR CONVERSION OF LABORATORIES 

CONTRACT NO. CITYWCUCF010904EL 

FORM OF PROPOSAL – WORK COST BREAKDOWN 

This form shall be filled out and submitted by the Contractor. The Total must equal the Total Price, 

under Section C.3. 

FAILURE TO COMPLETE THE WORK COST BREAKDOWN MAY RESULT IN 

DISQUALIFICATION OF THE BID. 

BIDDER: ____________________________________________________________________ 

DATE: ______________________________________________________________________ 

ITEM 

# DIVISION DESCRIPTION TOTAL COST 

1 01 Supervision/ Management $ 

2 01 Permits $ 

3 01 Insurance $ 

4 01 Bonds $ 

5 01 Safety $ 

6 01 Cutting & Patching $ 

7 01 Misc. General Requirements $ 

8 02 Selective Demolition $ 

9 07 

Thermal and Moisture Protection 

(Firestopping) 

$ 

10 10 Specialties (Visual Display Units) $ 

11 26 Roughing $ 

12 26 Power Panels $ 

13 26 Power Receptacles & Circuitry $ 

14 26 Lighting & Circuitry $ 

15 27 Tele5Data Communications $ 

16 28 Access Control $ 

17 28 Fire Alarm System $ 

18 28 

Allowance 5 Correction of Non5 

Compliance Issues for Existing Fire 

Alarm System (All Costs to be 

Verified) $ 25,000.00 

Overhead & Profit (15%) $ 

TOTAL (Must Equal Total Price) $ 

68


F. UNIT PRICES 

The Contractor shall provide the following Unit Prices which include, but are not limited to all 

necessary labor, material, taxes, supervision, insurance, equipment, tools, layout, freight, 

trucking, engineering, overhead, and profit, etc. in order to provide for a complete installation. 

The Unit Prices shall be used for added and deleted work in accordance with the Contract 

Documents. The Unit Prices shall be held for the duration of the Contract. 

Steel Pipe Sleeves up to 2" 

Firestopping 

Raceway 

Armored Cable 

Occupancy Sensor 9 Wall mounted 

_________ /Each 

_________/location 

_________/lf 

_________ /lf 

_________/Each 

Occupancy Sensor 9 Ceiling Mounted 

Power Pack for Occupancy Sensor 

Panel Board 9 flush mounted 

Thermal Magnetic Circuit Breaker 

GFCI Circuit Breaker 

Duplex Receptacle 

Quad Receptacles 

Duplex Receptacles 9 GFCI 

Quad Receptacles 9 GFCI 

Receptacle for Lab Equipment 

Toggle Switch 

Raceway 9 Wall type 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

_________/Each 

69


Dimmer Switch 

LED Exit Sign w/ Emergency Battery 

SS Cable Tray 

Power Strip 

Optical Fiber Cable 

Junction Box 

EMT Conduit 3/4" 

EMT Conduit 1/2" 

_________/Each 

_________/Each 

_________/lf 

_________/lf 

_________/lf 

_________/Each 

_________/lf 

_________/lf 

#10 Wire _________/lf 

#12 wire _________/lf 

Replacement of Existing 

Fire Alarm Pull Station 

(testing included in base bid) 

_________/Each 

G. CERTIFICATION 

The bidder hereby certifies to the best of its knowledge and belief and under penalty of 

perjury under the laws of the United States and the State of New York: 

1. That all information provided herein is accurate and truthful. 

2. That the bid has been executed with full authority to do so; that the bidder has not directly 

or indirectly entered into any agreement, participated in any collusion, or otherwise taken 

any action in restraint of free, competitive bidding in connection with these projects; and 

that all statements contained in this bid and in this certification are true and correct and 

made with full knowledge that STV Construction, Inc., CUNY and CUCF rely upon the 

truth of the statements contained in this bid and in the statements contained in this 

certification in awarding the contract for the projects. 

3. That neither the bidder nor its principals: 

A. are currently debarred, suspended, proposed for debarment, declared ineligible, 

or voluntarily excluded from bidding or contracting by any agency of 

government including but not limited to federal, state, regional, county or local 

government agency, in this or any other state including any department, 

70


division, commission, authority, office, branch, section and political subdivision 

or other governmental or quasi9governmental entity; 

B. have, within a three9year period preceding this bid, been convicted or had a civil 

judgment rendered against them for commission of fraud or a criminal offense 

in connection with obtaining, attempting to obtain or performing a public 

federal, state or local contract ; violation of federal or state antitrust statutes or 

commission of embezzlement, theft, forgery, bribery, falsification or destruction 

of records, making false statements, or receiving stolen property; 

C. are currently indicted for or otherwise criminally or civilly charged by a 

governmental entity (federal, state or local) with commission of any of the 

offenses enumerated in paragraph (B) of this certification; and 

D. have, within a three9year period preceding this bid, had one or more public 

contracts (federal, state or local) terminated for cause or default. 

4. The Bidder has, or will subcontract to firms having, current, valid contractor or trade 

licenses and permits required under applicable New York State and New York City laws 

for any trade or specialty area in which the firm seeks to perform work. 

5. During the term of construction of the projects that comprise this package, the contractor 

will have in place a suitable quality control and quality assurance program and an 

appropriate safety and health plan. 

6. The amount of the Price Proposal and the value of the Bidder’s outstanding incomplete 

contracts does not exceed the firm’s existing aggregate rating limit. 

7. The undersigned understands and agrees with the terms and conditions contained within the 

Form of Contract and Instructions to Bidders 1, Section III, Article 6: Times for 

Completion and Article 7: Liquidated Damages. 

MILESTONE 

TASK 

LIQUIDATED DAMAGE 

AMOUNT 

I. 

GC CONTRACT 

● Asbestos Abatement Complete 

$500.00 Per Calendar Day 

II. 

III. 

ALL PRIME CONTRACTS 

● Demolition Complete 

MECH/ EL/ PL CONTRACTS 

● Roughing Complete 



71


MILESTONE 

TASK 

LIQUIDATED DAMAGE 

AMOUNT 

GC CONTRACT 


IV. 

● Completion of GWB Installation 

V. ALL PRIME CONTRACTS 

$2,500.00 Per Calendar Day 

● Substantial Completion and NYC DOB Letter of Completion 

8. Where the bidder is unable to certify to any of the statements in this certification, the bidder 

shall explain below. 

____________________________________________________________________________ 

____________________________________________________________________________ 

____________________________________________________________________________ 

____________________________________________________________________________ 

_______________________________________________________________________ 

____________________________________________________________________________ 

____________________________________________________________________________ 

____________________________________________________________________________ 

____________________________________________________________________________ 

_______________________________________________________________________ 

____________________________________________________________________________ 

__________________________________________________________________________ 

72


IN WITNESS WHEREOF, the bidder has caused this instrument to be signed, attested to 

and sealed. 

Bidder: 

(Legal Firm Name) 

By: 

(Signature) 

(Printed or Typed Name) 

Title: ______________________________________ 

Address:_____________________________________ 

_________________________________ 

E9mail Address_________________ 

Telephone No. _______ 

Fax No. ____________ 

Date: 

Witness: ___________________________________________ 

Printed or Typed Name: _______________________________ 

Date:_______________________________________________ 

END OF PRICE PROPOSAL 

73


GENERAL REQUIREMENTS – SECTION 01 11 17 

DRAWING LIST 




GENERAL REQUIREMENTS – 01 11 17 

SECTION 01 11 17 

Drawing List 

QUEENS COLLEGE CONVERSION OF LABORATORIES 

Project Location: 6660 Kissena Blvd, Flushing, NY 11367 

Science Building: 2 nd Floor 

LIST OF DRAWINGS: 

Drawing Revision Date 

GENERAL DRAWINGS: 

G000.00 COVER SHEET 062512 

G001.00 GENERAL NOTES, SYMBOLS, AND BLDG CODES 091312 

ARCHITECTURAL DRAWINGS: 

A 001.00 ARCHITECTURAL ABBREVIATIONS AND SYMBOLS 062512 

A 002.00 AREAS OF WORK PLAN 062512 

A100.00 SECOND FLOOR DEMOLITION PLANS 091312 

A110.00 CONSTRUCTION PLAN ROOMS B237, B241, B211 091312 

A111.00 CONSTRUCTION PLAN ROOMS B243, B245, B203 091312 

A112.00 CONSTRUCTION PLAN ROOMS D231, D231A 091312 

A210.00 REFLECTED CEILING PLAN ROOMS B237, B241, B211 062512 

A211.00 REFLECTED CEILING PLAN ROOMS B243, B245, B203 062512 

A212.00 REFLECTED CEILING PLAN ROOMS D231, D231A 062512 

A301.00 LADDER AND CEILING DETAILS 062512 

A302.00 PARTITION TYPES 062512 

A401.00 ENLARGED PLAN & ELEVATIONS LAB B237 062512 




A405.00 ENLARGED PLAN & ELEVATIONS PREP RM. B203 062512 

A406.00 ENLARGED PLAN & ELEVATIONS PREP RM. B211 091312 

A407.00 ENLARGED PLAN & ELEVATIONS LAB D231 062512 

A408.00 ENLARGED PLAN & ELEVATIONS ROOM D231A 062512 

A601.00 DOOR SCHEDULE & DOOR DETAILS 062512 

A701.00 FINISH PLANS AND SCHEDULES 062512 

HAZMAT ABATEMENT DRAWINGS: 

H001.00 SECOND FLOOR ABATEMENT PLANS 062512 

FIRE PROTECTION DRAWINGS: 

FP001.00 SPRINKLER NOTES, SYMBOLS, AND ABBREVIATIONS 091312 

FP100.00 FIRE PROTECTION BASEMENT FLOOR PLAN 062512 

FP101.00 SECOND FLOOR PLAN FIRE PROTECTION 091312 

FP400.00 FIRE PROTECTION RISER DIAGRAM 062512 

0111171

GENERAL REQUIREMENTS – 01 11 17 

FP500.00 DETAIL SHEET 062512 

PLUMBING DRAWINGS: 

P001.00 PLUMBING NOTES, SYMBOLS, AND ABBREVIATIONS 091312 

P100.00 2ND FLOOR PLUMBING DEMOLITION PLAN 1 OF 2 062512 

P101.00 2ND FLOOR PLUMBING DEMOLITION PLAN 2 OF 2 062512 

P102.00 2ND FLOOR PLUMBING PART PLAN 1 OF 3 062512 



P401.00 PLUMBING DOMESTIC WATER & LAB WASTE RISER DIAGRAMS 062512 

P402.00 PLUMBING COMPRESSED AIR, VACUUM, & GAS RISER DIAGRAMS 062512 

P500.00 PLUMBING DETAILS 1 OF 2 062512 

P501.00 PLUMBING DETAILS 2 OF 2 062512 

P601.00 PLUMBING SCHEDULE SHEET 062512 

MECHANICAL DRAWINGS: 

EN001.00 ENERGY CODE COMPLIANCE 062512 

M001.00 MECHANICAL LEGEND, ABBREVIATIONS, AND NOTES 062512 

M101.00 2 ND FLOOR MECHANICAL DEMOLITION 091312 

M102.00 2 ND FLOOR MECHANICAL – NEW WORK SHEET 1 062512 



M105.00 ROOF PART PLANS AND DETAILS 062512 

M401.00 AIR RISER DIAGRAMS 062512 

M402.00 LABORATORY CONTROLS DIAGRAM 062512 

M501.00 MECHANICAL DETAILS – 1 062512 



M601.00 MECHANICAL SCHEDULES 062512 

ELECTRICAL DRAWINGS: 

E001.00 ELECTRICAL SYMBOLS LIST, ABBREVIATIONS, AND NOTES 091312 

E100.00 2ND FLOOR LIGHTING PART PLANS DEMO 091312 

E110.00 2 ND FLOOR POWER & LOW VOLTAGE PART PLANS DEMO 091312 

E120.00 2 ND FLOOR LIGHTING PART PLANS 062512 

E130.00 2 ND FLOOR POWER & LOW VOLTAGE PART PLANS 091312 

E500.00 DETAILS 091312 

E600.00 ELECTRICAL RISER DIAGRAMS 091312 

E601.00 ELECTRICAL PANEL SCHEDULES 062512 

E602.00 ELECTRICAL PANEL SCHEDULES 062512 

FIRE ALARM SYSTEM DRAWINGS: 

FA001.00 SYMBOL LIST, GENERAL NOTES & RISER DIAGRAM 091312 

FA100.00 CELLAR FIRE ALARM PLAN 062512 

FA101.00 2 ND FLOOR FIRE ALARM PLAN 062512 

END OF DRAWING LIST 

0111172


DWG. G001.00 (091312) 

GENERAL NOTES, SYMBOLS & BLDG. CODES 




1 

2 3 4 5 

GENERAL NOTES 

APPLICABLE BUILDING CODES 

STV 

D 

THE FOLLOWING NOTES SHALL APPLY THROUGHOUT. EXCEPTIONS ARE SPECIFICALLY NOTED ON EACH DRAWING. 

1. EACH CONTRACTOR SHALL FIELD VERIFY ALL DIMENSIONS AND CONDITIONS AT THE SITE AS REQUIRED TO VERIFY THE DRAWINGS 

AND TO PERFORM THIS WORK AS PER CONTRACT DOCUMENTS. ANY DISCREPANCY BETWEEN THE DRAWINGS AND THE SURVEY SHALL 

BE BROUGHT TO THE ATTENTION OF THE ARCHITECT IMMEDIATELY. NO WORK SHALL PROCEED UNTIL THE DISCREPANCY HAS BEEN 

RESOLVED. 

2.DRAWINGS ARE NOT TO BE SCALED. USE DIMENSIONS ONLY. ALL DIMENSIONS ON THE DRAWINGS MUST BE VERIFIED AT THE SITE BY 

EACH CONTRACTOR BEFORE ORDERING ANY MATERIAL OR PERFORMING ANY WORK. ANY DISCREPANCIES IN THE DRAWINGS AND 

SPECIFICATIONS SHALL BE REPORTED TO THE ARCHITECT IMMEDIATELY. NO CHANGE TO THE DRAWINGS OR SPECIFICATIONS IS 

PERMITTED WITHOUT WRITTEN CONSENT OF THE ARCHITECT. 

3. THE CONTRACTOR SHALL, UNLESS OTHERWISE PROVIDED IN THE CONTRACT DOCUMENTS, SECURE AND PAY FOR ALL REQUIRED 

CONSTRUCTION PERMIT(S), FEES, LICENSE AND INSPECTIONS NECESSARY TO EXECUTE THE WORK IN FULL COMPLIANCE WITH ALL NYC 

APPLICABLE CODES AND REGULATIONS AND WITH THE CONTRACT DOCUMENTS. 

4. COORDINATION OF ALL WORK UNDER THIS CONTRACT SHALL BE PROVIDED BY THE CONTRACTOR AS REQUIRED BY THE CONTRACT 

DOCUMENTS TO ENSURE THE QUALITY AND TIMELY COMPLETION OF THE WORK/PROJECT. 

5. EACH CONTRACTOR SHALL PERFORM ALL CUTTING AND PATCHING REQUIRED TO COMPLETE THE WORK OR TO MAKE ITS PARTS FIT 

TOGETHER PROPERLY WITHOUT COMPROMISING THE QUALITY OF THE WORK. 

THE FOLLOWING NOTES SHALL APPLY THROUGHOUT: 

1. WORK SHALL BE EXECUTED IN FULL COMPLIANCE WITH THE APPLICABLE PROVISIONS OF ALL LAWS, BYLAWS, STATUTES, 

ORDINANCES, CODES, RULES, REGULATIONS AND LAWFUL ORDERS OF PUBLIC AUTHORITIES BEARING ON THE PERFORMANCE AND 

EXECUTION OF THE WORK. 

2. THE WORK SHALL COMPLY WITH THE REQUIREMENTS OF THE FOLLOWING CODES AND STANDARDS. 

A. 2008 NEW YORK CITY BUILDING CODE. 

B. 2008 NEW YORK CITY FUEL GAS CODE. 

C. 2008 NEW YORK CITY MECHANICAL CODE. 

D. NEW YORK CITY PLUMBING CODE. 

E. NATIONAL FIRE PROTECTION ASSOCIATION (N.F.P.A. 72). 

F 

2011 NEW YORK CITY ELECTRICAL CODE 

G. UNDERWRITER LABORATORIES (UL DESIGN). 

STV INC. 

225 PARK AVE. SOUTH 

NEW YORK, NY 10003 

www.stvinc.com 

CONSULTANTS 

ENVIRONMENTAL 

MATRIX NEW WORLD 

120 EAGLE ROCK AVENUE SUITE 207 

EAST HANOVER, NJ. 07936 

t 9732401800 

COST ESTIMATING 

DACK CONSULTING SOLUTIONS 

6. ALL EXISTING FIRE RATED CONDITIONS DISTURBED BY THE WORK SHALL BE RESTORED TO MATCH THE ORIGINAL FIRE RATED 

CONDITIONS. 

H. FEDERAL STATE / LOCAL AUTHORITIES HAVING JURISDICTION. 

2 WILLIAM STREET SUITE 202 

WHITE PLAINS, NY. 10601 

7. THE GC SHALL BE RESPONSIBLE FOR ADEQUATELY BRACING AND PROTECTING ALL WORK DURING CONSTRUCTION AGAINST 

DAMAGE, BREAKAGE,COLLAPSE, DISTORTIONS, AND OFF ALIGNMENTS ACCORDING TO ALL APPLICABLE CODES AND STANDARDS AND 

PER BEST PRACTICES OF THE INDUSTRY. THE CONTRACTOR SHALL SUBMIT SHOP DRAWINGS FOR SHORING AND BRACING WITH 

CALCULATIONS SIGNED AND SEALED BY NEW YORK PROFESSIONAL ENGINEER. 

SPECIAL INSPECTIONS 

t 9146867102 

8. DURING CONSTRUCTION, TEMPORARY BAFFLES, PARTITIONS, ENCLOSURES, TO SEAL OPENINGS TO PREVENT DUST AND DIRT FROM 

FILTERING INTO OCCUPIED AREAS ARE TO BE PROVIDED BY THE GC. 

THE FOLLOWING SPECIAL INSPECTIONS REQUIRED IN ACCORDANCE WITH SECTION 27132 AND THE APPLICABLE 

SECTIONS OF THE BUILDING CODE ARE LISTED IN THE FOLLOWING TABLES: 

C 

9. THE CONTRACTOR SHALL KEEP THE WORK SITE FREE FROM DEBRIS AND ACCUMULATED REFUSE AND SHALL HAVE SOLE 

RESPONSIBILITY FOR PROTECTING ALL AREAS FROM ENTRY BY UNAUTHORIZED PARTIES. THE SITE SHALL BE LEFT BROOM CLEAN AT 

THE END OF EACH WORKING DAY. 

10. GENERAL CONTRACTOR SHALL COORDINATE THE INSTALLATION OF PLUMBING FIXTURES PRIOR TO THE CONSTRUCTION OF 

PARTITIONS BEHIND SUCH FIXTURES. 

11. ALL VERTICAL AND HORIZONTAL SHAFTS SHALL HAVE A MINIMUM FIRE RATING OF 2HOURS UNLESS REQUIRED OTHERWISE BY 

CODE. 

SPECIAL INSPECTION 

CODE SECTION 

FIRE ALARM BC 907 . BC 1704.13 

FIRE STOP, DRAFTSHOP, AND FIREBLOCK SYSTEM BC 1704.25 

MECHANICAL SYSTEMS BC 1704.15 

SPRINKLER SYSTEMS BC 1704.21 

1 

12. ALL LINTELS GREATER THAN 4'0" SHALL BE STRUCTURALLY SUPPORTED. 

ENERGY CODE COMPLIANCE INSPECTIONS BC 109.3.5 

13. ALL ELECTRICAL & MECHANICAL INDICATIONS ON ARCHITECTURAL DRAWINGS ARE FOR LOCATION PURPOSES ONLY. 

FIRE RESISTANCE RATED CONSTRUCTION BC 109.3.4 

14. THE GENERAL CONTRACTOR SHALL EXTEND ALL WALL FINISHES A MINIMUM OF 6" ABOVE SUSPENDED OR FURRED CEILINGS. 

15. ALL WORK SHALL BE INSTALLED SO THAT ALL PARTS THAT REQUIRE ACCESS ARE READILY ACCESSIBLE FOR INSPECTION, 

OPERATION, MAINTENANCE AND REPAIR. 

FINAL 28116.2.4.2, BC 109.5 

DIRECTIVE 14 OF 1975 AND 1 RCNY 10110 

ENERGY CODE PROGRESS INSPECTIONS 

16. EACH CONTRACTOR SHALL MAINTAIN FREE AND UNOBSTRUCTED ACCESS FROM ALL FLOORS AND ADJACENT SPACES INTO THE 

EXISTING FIRE STAIRS TO OUTSIDE OF THE BUILDING AT ALL TIMES. 

17. THE GENERAL CONTRACTOR SHALL PROVIDE BARRICADES AROUND WORK AREAS AS REQUIRED TO PREVENT STAFF, STUDENTS 

AND OTHER UNAUTHORIZED PERSONS FROM ENTERING THEREIN. 

HVAC AND SERVICE WATER HEATING EQUIPMENT 

HVAC AND SERVICE WATER HEATING SYSTEM CONTROLS 

DUCT PLENUM AND PIPING INSULATION AND SEALING 

(IB3) (IIB3) 

(IB4), (IIB4) 

(IB5) (IIB5) 

SEALS 

18. WHERE MANUFACTURERS NAMES AND PRODUCT NUMBERS ARE INDICATED ON THE DRAWINGS IT SHALL BE CONSTRUED TO MEAN 

THE ESTABLISHING OF QUALITY AND PERFORMANCE STANDARDS OF SUCH ITEMS. ALL OTHER PRODUCTS MUST BE SUBMITTED TO THE 

ARCHITECT FOR APPROVAL BEFORE THEY SHALL BE DEEMED EQUAL. 

INTERIOR LIGHTING POWER 

LIGHTING CONTROLS 

(IIC3) 

(IIC5) 

19. DIMENSIONS ON PLANS ARE INDICATED FROM SURFACE TO SURFACE BETWEEN WALLS, PARTITIONS AND OTHER ITEMS EXCLUSIVE 

OF FINISHES. 

20. EACH CONTRACTOR SHALL PATCH AND REPAIR ALL FLOORS, WALLS, CEILINGS, ETC. IN SPACES WHETHER IN SCOPE OR NOT THAT 

HAVE BEEN DAMAGED OR EXPOSED DUE TO WORK, REMOVALS OR TEMPORARY STORAGE AND FINISH THEM TO MATCH ADJOINING 

SURFACES. 

EXIT SIGNS 

MAINTENANCE INFORMATION 

(IIC6) 

(ID1),(IID1) 

OWNER WILL HIRE THE SPECIAL INSPECTION AGENCY OR ENGINEER AND ARCHITECT TO PERFORM THE SPECIAL 

INSPECTIONS. 

21. IF ANY UTILITIES OR SERVICES ARE INTERRUPTED DURING THE EXECUTION OF THE CONTRACT, IT IS THE RESPONSIBILITY OF EACH 

CONTRACTOR TO REROUTE AND/OR PROVIDE TEMPORARY SERVICE SO AS NOT TO DISRUPT ANY SERVICE TO THE BUILDING. 

EACH CONTRACTOR MUST NOTIFY THE CONSTRUCTION MANAGER TO ARRANGE THE SPECIAL INSPECTIONS AT LEAST 

SEVENTY TWO (72) HOURS PRIOR TO THE NEED FOR THE INSPECTION. 

B 

22. EACH CONTRACTOR SHALL BE RESPONSIBLE FOR ALL METHODS AND MEANS OF CONSTRUCTION AND PROVIDE ALL SAFEGUARDS 

TO INSURE SAFETY TO THE PUBLIC FOR THE DURATION OF THIS RENOVATION PROJECT. 

23. WHERE EXISTING DOOR FRAMES ARE TO BE REPLACED, REMOVE PORTION OF EXISTING WALL IN ORDER TO REMOVE AND REINSTALL 

NEW DOOR FRAME AND JAMB ANCHOR, PATCH AND MATCH EXISTING WALL CONSTRUCTION AND FINISHES. 

SUMMARY OF WORK 

24. THE GENERAL CONTRACTOR SHALL REMOVE, PROTECT AND STORE ALL FURNITURE, HARDWARE, EQUIPMENTS AS DIRECTED BY THE 

OWNER. 

25. EACH CONTRACTOR SHALL MAINTAIN NOISE CONTROL AT THE JOB SITE. CONSTRUCTION ACTIVITIES SHALL BE COORDINATED WITH 

THE COLLEGE SCHEDULE AND ACTIVITIES. 

CONVERSION OF FIVE (5) LABORATORIES AND (3) PREP ROOMS 

The project consists of plans and specifications to convert five existing physics and astronomy laboratories into biology teaching laboratories at Queens 

College Science Building Rooms B237, B241, B243, B245, & D231. Renovation of three existing prep rooms is also included in the scope of work. The labs 

occupy approximately 4,321 sf and approximately 766 sf of prep space, broken down as follows: 

PROJECT IDENTIFICATION 

CONVERSION OF LABORATORIES 

SCIENCE BUILDING 

26. EACH CONTRACTOR SHALL BE RESPONSIBLE FOR PROTECTING / COVERING ALL EXISTING WINDOW UNITS FROM DUST/ DIRT AND 

CLEAN TO CURRENT WORKING CONDITIONS AS FOUND. 

27. ELECTRICAL CONTRACTOR SHALL COORDINATE WITH COLLEGE FACILITIES REQUIREMENTS WHEN NEED ARISES TO DISCONNECT AND 

OR RELOCATE FIRE ALARM STROBES. THE EC SHALL PROVIDE CONTINOUS FIRE WATCH IF REQUIRED WHEN WORK IS EXECUTED ON THE 

FIRE ALARM SYSTEM. 

Lab Space 

B237 897sf 

B241 897sf 

B243 897sf 

B245 886sf 

D231 744sf 

QUEENS COLLEGE 

6660 Kissena Boulevard 

Flushing NY. 11367 

28. ALL HOT WORK ( WELDING, BRAZING, ETC) WILL REQUIRE COORDINATION, WRITTEN APPROVAL AND SIGN OFFS FROM COLLEGE 

PUBLIC SAFETY TO DEACTIVATE SMOKE DETECTORS WHILE WORKING AND NOTIFICATION WHEN COMPLETED ON A DAILY BASIS. 

29. AFTER ASBESTOS ABATEMENT PROCEDURES ARE COMPLETED, GENERAL CONTRACTOR TO REPLACE SEALANTS, INSULATION OR 

ANY OTHER ABATED MATERIAL WITH NONASBESTOS MATERIAL IN ORDER TO ASSURE SYSTEMS ARE RESTORED TO GOOD WORKING 

CONDITION. 

30. WHERE EXISTING WALLS ARE TO BE PATCHED OR NEW FINISH AND BASE OF WALL ARE TO MATCH EXISTING ADJACENT FINISHES, DO 

SO FOR THE ENTIRE LENGHT OF THE WALL OR REFER TO FINISH SCHEDULE. 

31. GC TO OBSERVE QUEENS COLLEGE ACCEPTED PROCEDURES FOR WASTEOUT, INCLUDING EARLY DAY SERVICE BY CARTING 

COMPANY, QUICK REMOVAL OF MINI CONTAINERS FROM PEDESTRIAN AREAS, ETC. 

32. GENERAL CONTRACTOR TO MAINTAIN THE WORK AREAS UNDER NEGATIVE AIR PRESSURE TO MINIMIZE THE PROPAGATION OF DUST 

AND ODORS TO OCCUPIED AREAS OF THE BUILDING. RETURN AIR GRILLES LEADING TO BUILDING HVAC SYSTEMS ARE TO BE COVERED 

DURING WORK PERIODS AND WHEN MATERIALS ARE OFFGASSING. 

Lab Prep Space 

B211 357sf 

B203 357sf 

D231A 52sf 

Work required for this project will be performed under four (4) separate contracts: 

A. Contract No. CITYWCUCF010904GC: General Construction Work GC 

B. Contract No. CITYWCUCF010904MECH: Mechanical/ HVAC Work MECH 

C. Contract No. CITYWCUCF010904EL: Electrical Work EC 

D. Contract No. CITYWCUCF010904PL: Plumbing & Fire Protection Work PC 

E. Each Trade Contractor shall be responsible for performing the work items specified or shown in the Specifications and accompanying drawings 

issued as a part of its Contract, and shall coordinate its work with that of the other Contractors. 

F. Each Trade Contractor and their subcontractors are required to cooperate with the Owner, the Owner’s representatives, and other Contractors 

in regard to scheduling, storage, deliveries, and construction. 

1 91312 ADDENDUM # 1 

MARK DATE DESCRIPTION 

PROJECT NO.: 

PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 

No. 2115419 

PAUL USURIELLO 

HECTOR ANDRADE 

JAMES HEMMERLY 

SANDRA BENJAMIN 

A 

1 2 3 4 5 

SHEET TITLE 

GENERAL 

NOTES, 

SYMBOLS & 

BLDG. CODES 

G001.00 

2 

of 65 

9/10/2012 2:15:52 PM


DWG. A100.00(091312) 

SECOND FLOOR DEMOLITION PLANS 




1 

2 3 4 5 

DEMOLITION NOTES 


D 

7' 

7 

6 

5 4 3 2 

1. COORDINATE ALL REMOVAL WORK WITH NEW CONSTRUCTION. 

2. SEE MECHANICAL, PLUMBING, ELECTRICAL, FIRE PROTECTION AND ASBESTOS ABATEMENT DWGS. FOR 

ADDITIONAL DEMOLITION INFORMATION. 

3. CONTRACTOR SHALL DISPOSE ALL EXISTING FURNITURE / EQUIPMENT AND SHALL COORDINATE WITH 

THE CONSTRUCTION MANAGER TO DETERMINE AS DIRECTED BY THE OWNER TO SALVAGED SPECIFIC 

FURNITURE/EQUIPMENT AND TURN THEM OVER TO OWNERTO BE STORED AT LOCATION DESIGNATED BY OWNER. 

4. REMOVE EXISTING VCT FLOORING AND WALL BASE INCLUDING MASTICS AND ADHESIVES IN ALL ROOMS IN SCOPE OF 

WORK, AND EITHER SHOT BLAST OR DIAMOND GRIND ALL FLOORS TO RECEIVE NEW EPOXY FLOORING. 

5. ALL EXISTING NONFIXED LAB EQUIPMENT SHALL BE REMOVED BY QUEENS COLLEGE FACILITIES DEPARTMENT. 

9. REMOVE EXISTING ACOUSTICAL SUSPENDED CEILING AND ITS SUPPORTS IN ROOMS B211 & D231A 

10. ALL EXISTING BLACK BOARDS AND WHITE BOARDS TO BE REMOVED. 

1 

1 

1 





CONSULTANTS 

ENVIRONMENTAL 




t 9732401800 

11. GENERAL CONTRACTOR TO COORDINATE WITH ELECTRICAL CONTRACTOR FOR PROPER DISPOSAL 

OF ALL LIGHTING FIXTURES AND FLOURESCENT BULBS AND MECHANICAL CONTRACTOR FOR PROPER DISPOSAL 

OF THERMOSTATS SCHEDULED TO BE REMOVED. GENERAL CONSTRACTOR TO PROPERLY DISPOSE OF UNIVERSAL 

WASTE AND FLOURESCENT BULBS AS SPECIFIED IN SECTION 132860 OF THE CONTRACT SPECIFICATIONS. 




PHYSICS LAB 

G' 


t 9146867102 

D235 

31'3 1/2" 

H' 

DEMOLITION KEY NOTES 

C 

Room 

B215 

H 

1 

2 

EXISTING LAB BENCHES TO BE REMOVED. 

EXISTING DOORS AND FRAMES TO BE REMOVED 

3 

I 

3 

4 

EXISTING SINKS AND CABINETS TO BE REMOVED 

EXISTING FURNITURE AND EQUIPMENT TO BE REMOVED SERVICE CONNECTIONS TO BE REMOVED BY 

MECH, EC AND PC. 

1 

2 

1 

Biology Lab 

B237 

4 

2 

4 

5 

EXISTING SMARTBOARD TO BE REMOVED AND ALL ASSOCIATED MOUNTING FRAME AND HARDWARE. 

DEMOLITION KEY NOTES ARE TYPICAL FOR ALL LABS AND PREPARATION ROOMS. 

J 

B 

A 

2 

Corridor 

C001 

2 

2 

5'8" TYP. 

1 

1 

13'4" TYP. 

Biology Lab 

B241 

Biology Lab 

B243 

Biology Lab 

B245 

30'8 3/4" 

Corridor 

C002 

1 

4 

4 

3 

1 

3 

2 

2 

3 

2 

Prep. Room 

B211 4 

5 

Office 

B209 

Office 

B207 

4 

Prep. Room 

B203 

4 

1 

4 

Office 

B201 

Corridor 

C003 

K 

L 

M 

M' 

N 

O 

O' 

P 

Room 

D233 

Inst. Storage 

D233A 

5 4 3 

Corridor 

C002 

Biology Lab 

2 

D231 

4 

4 

4 

2'6" TYP. 

15'0" TYP. 

2 

Prep. Room 

Pipe Space 

D231A 

D227 

LAB 

D223 

Q 

R 

S 

T 

E 

A 

C 

B 



PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

SEALS 








ISSUE BLOCK 




SHEET TITLE 

No. 2115419 


1 

SECOND FL. DEMOLITION PLAN "AREA B" 

Q 

2 

SECOND FL. DEMOLITION PLAN "AREA D" 

D 

SECOND FLOOR 

DEMOLITION 

PLANS 

A100.00 1/8" = 1'0" 

0 4' 8' 16' 

A100.00 1/8" = 1'0" 

0 4' 8' 16' 

1 2 3 4 5 

KEY PLAN 

A100.00 

5 

of 65 

9/13/2012 2:17:32 PM


DWG. A110.00(091312) 

CONSTRUCTION PLAN ROOMS B237, B241, & B211 




1 

2 3 4 5 


D 

6 

5 4 3 2 





3'0" 

PHYSICS LAB 

D235 

34'0" EPOXY COUNTERTOP TYP. 

1'6" 

6'3" +/ 

1 

8'0" 

Room 

B215 

H' 

H 

CONSTRUCTION NOTES 

1. REFER TO SHEET G001 FOR GENERAL ARCHITECTURAL NOTES. 

2. FOR DOOR SCHEDULE,DOOR TYPES AND DETAILS SEE DRAWINGS A601 

3. FOR FINISH SCHEDULE SEE DRAWING A701. 

4. FOR CASEWORK / EQUIPMENT SEE A400'S SERIES DRAWINGS. 

5. ALL DIMENSIONS ARE NOMINAL AND TO BE FIELD VERIFIED BY CONTRACTOR. 

6. AFTER REMOVAL OF EXIST. DUCTS, PIPES, CONDUITS WHICH PENETRATED EXIST. 

WALLS AND FLOOR SLABS, CONTRACTOR TO INFILL OPENINGS TO MATCH EXIST. 

MATERIAL AND FIRE RATING. "REFER TO SECTION 017329 OF THE GENERAL 

CONDITIONS FOR CUTTING AND PATCHING REQUIREMENTS" 

1 

CONSULTANTS 

ENVIRONMENTAL 




t 9732401800 





t 9146867102 

12'0" TYP. 

5'0" 5'0" 5'0" 

2 

4 

I 

7. FOR PARTITION TYPES SEE DRAWING A302 

8. EXISTING FLOOR SLAB TO BE PATCHED, REPAIRED, LEVELED AND PREPARED TO 

RECEIVED NEW FINISHES 

9. PATCH ALL HOLES AND OTHER UNPROTECTED OPENINGS IN EXISTING RATED 

SHAFTS. NEW PATCHES TO MATCH EXISTING FIRERATING OF ASSEMBLY. 

C 

B 

Corridor 

C001 

21'10" 21'9 1/4" 

5 

2 

5 

2'2" 

2'2" 

1'6" 

2'0" 

1'6" MIN. 

6'3 1/4" 

Biology Lab 

B237 

8'6" 

7'6" 

8'0" 

Biology Lab 

B241 

3 

4 A401.00 

2 

5 

6'2" 

2 

3'0" 5'0" 5'0" 5'0" 7'2 1/2" +/ 

1'6" MIN. 

6 

12'6" 

4'0" TYP. 

7 

34'0" 

7'5 3/4" 

4'0" TYP. 

5 1 

7 

2'0" 

2 

5 A402.00 

3 

4 

8'0" 

3'8" 

3'7" +/ 

2 

4 

1 

3'8 1/4" 

5'0" 

1'11 3/4" 

4 

3 

6" 

8'0" 

2'4" 

2 4 

3 

6 1/4" 

8'2" 

8'0" 

A406.00 6 

5 

1 

Prep. Room 

B211 

4'0" 3'11" 2'0" 

2 

A406.00 4 

3 

Office 

B209 

8'0" 

2'10" 

Corridor 

C003 

J 

K 

L 

1 

2 

3 

CONSTRUCTION KEY NOTES 

NEW SINK. SEE PLUMBING DRAWINGS. 

4 NEW EMERGENCY EYEWASH. SEE PLUMBING DRAWINGS. 

5 

NEW ADA SINK. SEE PLUMBING DRAWINGS. 

EMERGENCY SHOWER / EYEWASH WITH RECESSED MIXING VALVE, SEE PLUMBING DWGS. 

PATCH PORTIONS OF EXISTING WALLS & FLOORS AS REQUIRED AND FINISH 

TO MATCH EXISTING ADJACENT 

6 HIGH EFFICIENCY FUME HOOD, SEE MECH, PLUMB DRWGS. 

7 SMART BOARD, SEE ELECTRICAL DRWGS. 

8 

CUT NEW OPENING FOR HOLLOW METAL FRAME; PROVIDE SQUARE AND TRUE FRAMED 

OPENING; PATCH AND REPAIR WALL AS REQUIRED TO ALIGN WITH ADJACENT WALL 

SURFACES. 

SEALS 







Biology Lab 

B243 

SEE DWG. A111 

Office 

B207 



ISSUE BLOCK 

A 

1 

CONSTRUCTION PLANS ROOMS B237, B241, B211 

A110.00 1/4" = 1'0" 

0 2' 4' 8' 

1 2 3 4 5 

A 

E C 

D 

KEY PLAN 

B 


PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 




SHEET TITLE 

CONSTRUCTION 

PLAN ROOMS 

B237, B241 & 

B211 

A110.00 

6 

of 65 

No. 2115419 



9/10/2012 2:13:45 PM


DWG. A111.00(091312) 

CONSTRUCTION PLAN ROOMS B243, B245, & B203 




1 

2 3 4 5 


D 

6 

5 4 3 2 





Office 

B209 



CONSULTANTS 

ENVIRONMENTAL 



1'6" 

SEE DWG. A110 

1 

2'0" 

8'0" 

Office 

L 










1 


t 9732401800 





t 9146867102 

B207 





C 

21'9 3/4" 

5 

3'0" 5'0" 5'0" 5'0" 

9'2" +/ 

2 4 

7" 

Corridor 

C003 

M 

M' 


B 

Corridor 

C001 

22'0 1/2" 

2 

1'10" 

2 

5 

7 

1'6" MIN. 

4 

12'0" TYP. 

4'0" 

12'6" 

6'4" 

Biology Lab 

B243 

2 

5 A403.00 

3 

4 

7'6" 

8'0" 

5'0" 5'0" 5'0" 

7 

3'8" 

6'3" +/ 

1 

4'4" 

1 

3 

1 

1 

2 

1 

6" 

1'9" 

4 

2 

A405.00 6 

3 

5 

2 

A405.00 

4 

Prep. Room 

3 

B203 

5'3" 8'2" 

8'5" 

4'0" 3'8" 2'0" 

8'0" 

N 

O 

O' 

1 

2 

3 



5 







8 



SURFACES. 

SEALS 


3'0" 

3'0" 

4'0" TYP. 

1'10" 

8'6" 

Biology Lab 

B245 

7'6" 

2 

5 A404.00 

3 

4 

4'0" 4'4 3/4" 

3'8" 

2 4 

8'0" 

Office 

B201 






7 

8 

2'0" 

P 

A 

1 

A111.00 

8 

5 

Corridor 

C002 

CONSTRUCTION PLANS ROOMS B243, B245, B203 

1/4" = 1'0" 

0 2' 4' 8' 

1 2 3 4 5 

A 

E C 

D 

KEY PLAN 

B 




PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 




SHEET TITLE 

CONSTRUCTION 

PLAN ROOMS 

B243, B245 & 

B203 

A111.00 

7 

of 65 

No. 2115419 


9/10/2012 2:13:46 PM


DWG. A112.00(091312) 

CONSTRUCTION PLAN ROOMS D231 & D231A 




1 

2 3 4 5 


D 





5 4 3 

CONSULTANTS 

ENVIRONMENTAL 



P 



t 9732401800 

Corridor 

C002 






1 





t 9146867102 

C 

2'7" 

2'0" 

9 

3'0" 

1 

5 

12'0" TYP. 

Q 










4'4" 

1'6" 

8'6" 


1 


7'6" 

Biology Lab 

7 

D231 

5'0" 

4'4" 

5'0" 

EPOXY COUNTER TOP 25'2" VIF. 

2 

3 


5 







8 



SURFACES. 

SEALS 

R 

B 

8'0" 

4'4" 

2 


6 

3 

4 

A407.00 

3 

5 

1'9" 

2 

4 

3'0" 

6'2" 3'0" 1 1/4" 

6'4" 

S 






10 

1 

2 

1'6" MIN. 

A 

A408.00 

3 

4 

Prep. Room 

D231A 

T 

E 

A 

C 

B 




PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 




SHEET TITLE 

No. 2115419 


1 

A112.00 1/4" = 1'0" 

CONSTRUCTION PLANS ROOMS D231 & D231A 

1 2 3 4 5 

D 

KEY PLAN 

CONSTRUCTION 

PLAN ROOMS 

D231 & D231A 

A112.00 

8 

of 65 

9/12/2012 4:49:59 PM


DWG. A404.00(091312) 

ENLARGED PLAN & ELEVATIONS LAB B245 




1 

2 3 4 5 


D 

C13 

EXIST. 

ACCESS 

PANEL 

E18 

E4 

C2 

C2 

C2 

C1 

CASEWORK SCHEDULE LAB B245 

ITEM 

# DESCRIPTION WIDTH DEPTH QTY 

PROVIDED 

BY 

INSTALLED 

BY 





C 

2'10 1/2" 1'7 1/2" 2'6" 

2'10" 1'6" 2'6" 

C8 

C30 

3 

A404.00 

C1 

C23 

C29 

C2 C2 C1 C1 C2 C2 C1 C1 C2 C2 C1 C1 

C17 

E11 

SOUTH ELEVATION LAB B245 

1/4" = 1'0" 

C17 

C25 

C5 

C16 

C17 

C9 

C27 

C6 

C17 

C5 

3'0" 1'8" 2'6" 

C30 

C28 

C22 

C1 

1'6" 2'6" 

3'0" 

8'6" 

3'0" 1'8" 2'6" 

C5 

5 

A404.00 

C27 

C17 

C16 

C7 C7 C7 

WEST ELEVATION LAB B245 

1/4" = 1'0" 

1'6" 

C1 C1 C13 

C30 C22 C30 C23 

2'10 1/2" 1'7 1/2" 2'6" 

C4 

8'6" 

C1 UPPER CABINETDOUBLE GLASS 2' 6" 1' 0" 9 GC GC 

DOOR 


DOOR 

C4 BASE CABINET ADA 2' 6" 1' 5" 7 GC GC 

C5 BASE CABINETDOUBLE DOOR & 4' 0" 1' 9 5/8" 2 GC GC 

2 DRAWERS 

C6 BASE CABINET SINGLE DOOR & 2' 0" 1' 10" 1 GC GC 

DRAWER 

C7 BASE CABINET 1DOOR 1' 6" 1' 9 5/8" 24 GC GC 

PULLOUT WRITING TABLET ADA 

C8 BASE CABINET ADA SINK 3' 0" 2' 0" 1 GC GC 

C9 AUDIO VISUAL CABINET 2' 6" 1' 10" 1 


DOOR 

C16 COUNTER TOP 34' 0" 1' 6" 1 GC GC 


C19 BASE CABINETDOUBLE DOOR & 5' 0" 1' 9 3/4" 1 GC GC 

2 DRAWERS 





C28 EPOXY DROPIN SINK 2' 0" 1' 4" 1 GC GC / PC 

C29 EPOXY ADA DROPIN SINK 1' 2" 10" 1 GC GC /PC 

C30 SINK FAUCET 2 GC PC 

68 

1 

CONSULTANTS 

ENVIRONMENTAL 




t 9732401800 





t 9146867102 

2 

C4 

A404.00 

C7 C7 C4 C4 C7 C7 C4 C4 C7 

NORTH ELEVATION LAB B245 

1/4" = 1'0" 

6 

C7 

C4 

C4 

C7 

C7 

E5 C19 

E5 

C19 

C8 

5 4 3 

4 

A404.00 1/4" = 1'0" 

EAST ELEVATION LAB B245 

SPECIALTY EQUIPMENT SCHEDULE LAB B245 

ITEM 

# DESCRIPTION SIZE QTY 

INSTALLED 

BY 

PROVIDED 

BY 

E4 SMART Board Interactive 6'5 1/2"W X 4'1 1/2" H 1 EC EC 

Whiteboard Model 685ix 

E5 PLANT INCUBATOR 31" x 46" x 46" 2 GC COLLEGE 

E11 REFRIGERATOR 33" X 35" x 84" 1 GC COLLEGE 

E18 BRACKET MOUNTED FIRE 

EXTINGUISHER 

2'6" 1 

5 

SEALS 

33'10 1/2" 

B 

C16 

Prep. Room 

N 

ELEVATION NOTES 

1. FOR DOOR TYPES & SCHEDULE SEE DWG A601 


C4 C4 C4 C4 C4 C4 

C4 

C1 C2 C2 C1 C1 C2 C2 C1 C1 C2 C2 C1 C1 

B203 

2. FOR FINISH SCHEDULE SEE DWG A701 

3. FOR ELECTRICAL DEVICES, SEE ELECTRICAL DRAWINGS 



C7 

C7 

C7 C7 

C7 C7 

C7 C7 

C17 C17 C17 C17 

E5 

E5 

C30 

4. FOR CASEWORK AND EQUIPMENT SHOWN SEE SCHEDULE FOR 

RESPONSIBLE PROVIDERS AND INSTALLATION PARTIES 

5. PROVIDE WALL BLOCKING AS NECESSARY AT ALL INSTALLED 

CASEWORK. SEE MANUFACTURER'S SPECIFICATIIONS. 




C7 

C7 

C7 

C7 

C7 

C7 

C7 

C7 

C28 

O 

6. FOR GAS, VACUUM AND COMPRESSED AIR UTILITIES TO BE PROVIDED, SEE 

PLUMBING DRAWINGS. 

C1 

A 

Corridor 

C001 

1/4" = 1'0" 

C7 

C7 

C2 

C5 

C2 

C7 

C27C6 

8'6" 

ENLARGED PLAN LAB B245 

C7 

C9 

Biology Lab 

B245 

Corridor 

C002 

E4 

C7 

C7 

C25 

5 

C5 

4'0" 

2 

A404.00 

3 

4 

E11 

C7 

C7 

E18 

C19 

C22 

C1 

C29 

C8 

C13 

C23 

EXIST. 

ACCESS 

PANEL 

1 2 3 4 5 

0 

C30 

5'0" 

3'0" 

2' 4' 8' 

O' 

P 

E 

A 

C 

D 

KEY PLAN 

B 




PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 




SHEET TITLE 

ENLARGED 

PLAN & 

ELEVATIONS 

LAB B245 

A404.00 

17 

of 65 

No. 2115419 


9/13/2012 12:13:16 PM


DWG. A406.00(091312) 

ENLARGED PLAN & ELEVATIONS PREP RM B211 




1 

2 3 4 5 


D 

C1 

C13 

C2 

CASEWORK SCHEDULE PREP ROOM. B211 

ITEM # DESCRIPTION WIDTH DEPTH QTY 

PROVIDED 

BY 

INSTALLED 

BY 





CONSULTANTS 

C 

3 

A406.00 

2'6" 2'0" 2'6" 

C10 

C11 C11 C11 

SOUTH ELEVATION PREP. RM. B211 

1/4" = 1'0" 

10'9 1/4" 

5 

A406.00 

C33 

C23 

C30 

C11 

E14 E7 C8 

WEST ELEVATION PREP. RM. B211 

1/4" = 1'0" 

E18 C1 C1 C1 C1 C1 

C1 UPPER CABINETDOUBLE 2' 6" 1' 0" 5 GC GC 

GLASS DOOR 


GLASS DOOR 

C5 BASE CABINETDOUBLE 4' 0" 1' 9 5/8" 6 GC GC 

DOOR & 2 DRAWERS 

C8 BASE CABINET ADA SINK 3' 0" 2' 0" 1 GC GC 

C10 DESK 4' 0" 2' 6" 1 COLLEGE GC 

C11 TALL STORAGE CABINET 3' 0" 1' 4" 5 GC GC 


GLASS DOOR 




C29 EPOXY ADA DROPIN SINK 1' 2" 10" 1 GC GC / PC 

C30 SINK FAUCET 1 GC PC 

C33 STAINLESS STEEL PEG 2' 6" 2' 6" 1 GC GC 

BOARD 

26 

1 

ENVIRONMENTAL 




t 9732401800 





t 9146867102 

2 

C33 

C30 

C23 

C29 

C8 

E1 C11 C11 

NORTH ELEVATION PREP. RM. B211 

10'9 1/4" 

4 

C11 

C20 

C5 C5 C10 

EAST ELEVATION PREP. RM. B211 

4'6" 2'6" 

SPECIALTY EQUIPMENT SCHEDULE PREP ROOM B211 

ITEM # DESCRIPTION SIZE QTY PROVIDED BY INSTALLED BY 

E1 DELI REFRIGERATOR 52" X 32" X 78" 1 COLLEGE GC 

E7 DISH WASHER 24" x 24" x 35" 1 COLLEGE GC/ PC/ EC 

E14 ICE MAKER 32" X 28" 1 COLLEGE GC/ PC 

E15 BENCH TOP INCUBATOR 24" X 26" X 40" 1 COLLEGE GC 

E16 DRYING OVEN 30"X22"X32" 1 COLLEGE GC 

E18 BRACKET MOUNTED FIRE 2'6" 1 GC GC 

EXTINGUISHER 

6 

SEALS 

A406.00 

1/4" = 1'0" 

A406.00 

1/4" = 1'0" 

3 2 

ELEVATION NOTES 

B 

Biology Lab 

B237 

C33 

C30 

C29 

Room 

B215 

E1 

Prep. Room 

C11 

C11 

Corridor 

I 

E1 

E16 

C21 

3'0" 

C11 

1. FOR DOOR TYPES & SCHEDULE SEE DWG A601 

2. FOR FINISH SCHEDULE SEE DWG A701 

3. FOR ELECTRICAL DEVICES, SEE ELECTRICAL DRAWINGS 

4. FOR CASEWORK AND EQUIPMENT SHOWN SEE SCHEDULE FOR 

RESPONSIBLE PROVIDERS AND INSTALLATION PARTIES 

5. PROVIDE WALL BLOCKING AS NECESSARY AT ALL INSTALLED 

CASEWORK. SEE MANUFACTURER'S SPECIFICATIIONS. 

6. FOR GAS, VACUUM AND COMPRESSED AIR UTILITIES TO BE PROVIDED, SEE 

PLUMBING DRAWINGS. 







A 

Biology Lab 

B241 

1 

A406.00 

C8 

C23 

C2 

E7 

C13 

E14 

A406.00 6 

C21 

5 

C11 C11 C11 

1/4" = 1'0" 

E16 

C5 

C5 

B211 

2 

A406.00 

3 

Office 

B209 

E15 

C5 

C5 

4 

C5 

C5 

C1 

C1 

C20 

C1 

C1 

C10 

C1 

E18 

ENLARGED PLAN LAB B211 

0 

C003 

2' 4' 8' 

J 

K 

6 

A406.00 

1 2 3 4 5 

C5 

C5 

ISLAND LAB BENCH @ RM B211 

1/4" = 1'0" 

E 

A 

C 

D 

KEY PLAN 

B 




PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 




SHEET TITLE 

ENLARGED 

PLAN & 

ELEVATIONS 

PREP. RM. B211 

A406.00 

19 

of 65 

No. 2115419 


9/13/2012 12:13:16 PM


DWG. FP001.00(091312) 

SPRINKLER NOTES, SYMBOLS AND 

ABBREVIATIONS 




1 

2 3 4 5 


D 

AD 

AFF 

ATS 

CL OR C L 

CLG 

CONT 

CP 

DIM 

DN 

LIST OF ABBREVIATIONS 

ACCESS DOOR 

ABOVE FINISH FLOOR 

AUTOMATIC TRANSFER SWITCH 

CENTER LINE 

CEILING 

CONTINUATION 

CONTROL PANEL 

DIMENSION 

PIPE DOWN THROUGH FLOOR 

EXIST SP 

LIST OF SYMBOLS 

EXISTING SPRINKLER PIPING 

NEW SPRINKLER DISTRIBUTION PIPING 

PIPE UP OR RISE 

PIPE DN OR DROP 

CAP 

TEST AND DRAIN 

SHUT OFF VALVE (BUTTERFLY OR GATE) 

NYC SPRINKLER NOTES 

1. AUTOMATIC SPRINKLER SYSTEM SHALL COMPLY WITH SEC. 903 & APPENDIX Q OF NYC BUILDING CODE & NFPA 13&2002. 

2. CONSTRUCTION DOCUMENTS FOR STANDPIPE SYSTEM SHALL CONTAIN PLANS THAT INCLUDE THE INFORMATION AND 

DATA LISTED IN SEC. 903.1.2 OF NYC BUILDING CODE. 

3. APPROVED AUTOMATIC SPRINKLER SYSTEM IN NEW BUILDINGS AND STRUCTURES SHALL BE PROVIDED ON THE LOCATIONS 

DESCRIBED IN SEC. 903.2 OF NYC BUILDING CODE. 

4. AUTOMATIC SPRINKLER SYSTEM SHALL BE DESIGNED AND INSTALLED IN ACCORDANCE WITH SEC. 903.3.1 THROUGH 903.3.7 

OF NYC BUILDING CODE. 

5. WHERE THE PROVISIONS OF NYC BUILDING CODE REQUIRE THAT A BUILDING OR PORTION THERE OF BE EQUIPPED THROUGHOUT 

WITH AN AUTOMATIC SPRINKLER SYSTEM IN ACCORDANCE WITH SEC. 903.3.1.1, SPRINKLER SHALL BE INSTALLED THROUGHOUT 

IN ACCORDANCE WITH NFPA 13 AS MODIFIED IN APPENDIX Q EXCEPT AS PROVIDED IN SEC. 903.3.1.1.1 OF NYC BUILDING CODE. 

6. AUTOMATIC SPRINKLERS SHALL NOT BE REQUIRED IN THE ROOMS OF AREAS WHICH ARE LISTED IN 903.3.1.1.1 OF NYC BUILDING 

CODE AS LONG AS AN APPROVED AUTOMATIC FIRE DETECTION SYSTEM IN ACCORDANCE WITH SEC. 907.2 AND AN ALTERNATIVE 

EXTINGUISHING SYSTEM IN ACCORDANCE INSTALLED IN ACCORDANCE WITH SEC. 903.3.1 THROUGH WITH SEC. 904. 

7. SPRINKLERS SHALL NOT BE OMITTED FROM ANY ROOM MERELY BECAUSE IT IS DAMP, OF FIRE&RESISTANCE&RATED CONSTRUCTION 

OR CONTAINS ELECTRICAL EQUIPMENT AS PER SEC. 903.3.1.1.1 OF THE NYC BUILDING CODE. 

SPECIAL INSPECTIONS 

THE FOLLOWING SPECIAL INSPECTIONS REQUIRED IN ACCORDANCE 

WITH SECTION 28&132 AND THE APPLICABLE SECTIONS OF 

THE BUILDING CODE ARE LISTED IN THE FOLLOWING TABLES: 

& FIRE STOPPING BC 1704.25 

& SPRINKLER SYSTEMS BC 1704.21 

THE CONTRACTOR MUST NOTIFY THE ARCHITECT OR 

ENGINEER FOR SPECIAL INSPECTION AT LEAST 

72 HOURS BEFORE THE SPECIFIC WORK COMMENCES. 





CONSULTANTS 

ENVIRONMENTAL 




t 973&240&1800 





DR 

DRAIN 

UNION 

8. WHERE AUTOMATIC SPRINKLER SYSTEM ARE REQUIRED BY NYC BUILDING CODE, QUICK&RESPONSE OR RESIDENTIAL AUTOMATIC 

SPRINKLERS SHALL BE INSTALLED IN THE AREAS LISTED SEC. 903.3.2 OF NYC BUILDING CODE. 

t 914&686&7102 

C 

DROP 

DWG 

EL 

EX OR EXIST 

FCVA 

FD 

FHV 

PIPE DROPPING BETWEEN FLOORS 

DRAWING 

ELEVATION 

EXISTING 

FLOOR CONTROL VALVE ASSEMBLY 

FLOOR DRAIN 

FIRE HOSE VALVE 

# 

SPRINKLER FLOOR CONTROL VALVE ASSEMBLY; FCVA 

NODE (SPRINKLER HYDRAULIC CALCULATIONS) 

RECESSED PENDANT SPRINKLER HEAD 

UPRIGHT SPRINKLER HEAD 

POINT OF NEW CONNECTION 

9. AUTOMATIC SPRINKLERS SHALL BE INSTALLED WITH DUE REGARD TO OBSTRUCTIONS THAT WILL DELAY ACTIVATION OR OBSTRUCT 

THE WATER DISTIBUTION PATTERN, AUTOMATIC SPRINKLERS SHALL BE INSTALLED IN OR UNDER COVERED KIOSKS, DISPLAYS, 

BOOTH, CONCESSION STANDS, OR EQUIPMENT THAT EXCEEDS 4 FEET IN WIDTH NOT LESS THAN 3 FOOT CLEARANCE SHALL BE 

MAINTAINED BETWEEN AUTOMATIC SPRINKLERS AND TOP OF FILES OF COMBUSTIBLE FIBERS SEC. 903.3.3 OF NYC BUILDING CODE. 

10. WATER SUPPLIES FOR AUTOMATIC SPRINKLER SYSTEM SHALL COMPLY WITH SEC. 903.3.5 OF NYC BUILDING CODE AND SEC. 903.3.1 

THE POTABLE WATER SUPPLY SHALL BE PROTECTED AGAINST BACK FLOW IN ACCORDANCE WITH THE REQUIREMENTS OF 

SEC. 903.3.5 THE NYC PLUMBING CODE, AND RULES OF THE NYC DEPARTMENT OF ENVIRONMENTAL PROTECTION. 

11. ALL VALVES CONTROLLING THE WATER SUPPLY FOR AUTOMATIC SPRINKLER SYSTEM, PUMPS, TANKS, WATER LEVELS AND 

TEMPERATURES, CRITICAL AIR PRESSURES AND WATER&FLOW SWITCHES ON ALL SPRINKLER SYSTEM SHALL BE ELECTRICALLY 

SUPERVISED 

BY THE FIRE ALARM SYSTEM AS PER SEC. 903.4 OF THE NYC BUILDING CODE. 

SPRINKLER SYSTEM INFORMATION 

BUILDING OCCUPANCY CLASSIFICATION 

GROUP: BUSINESS (CLASSROOMS) 

SPRINKLER HEADS 

MANUFACTURER: RELIABLE AUTOMATIC SPRINKLER CO. 

FIN FL 

FP 

FSP 

FINISHED FLOOR 

FIRE PROTECTION 

FIRE STANDPIPE 

TS 

TAMPER SWITCH (OR VALVE) 

12. APPROVED SUPERVISED INDICATING CONTROL VALVES SHALL BE PROVIDED AT THE POINT OF CONNECTION TO THE RISER 

ON EACH FLOOR IN HIGH&RISE BUILDINGS AS PER SEC. 903.4.3 OF THE NYC BUILDING CODE. 

13. THE DOCUMENTS OR PORTIONS THERE OF LISTED IN CHAPTER 2 OF NFPA 13&2002 ARE REFERENCED WITHIN NFPA&13 

AND SHALL BE CONSIDERED PART OF THE REQUIREMENT OF THIS DOCUMENT. 

SPRINKLER MODEL: G4A (BSA 587&75&SA) CONCEALED TYPE 

TYPE: CONCEALED QUICK RESPONSE 

ORIFICE SIZE: 1/2" TEMPERATURE RATING: 

ORDINARY 165° F 

INV EL 

INVERT ELEVATION 

14. OCCUPANCY CLASSIFICATION SHALL COMPLY WITH CHAPTER 5 OF NFPA 13&2002. 

SPRINKLER MODEL: GFR (MEA 258&93&E) 

B 

HVAC 

HEATING, VENTILATION & AIR CONDITIONING 

MAX 

MAXIMUM 

MIN 

MINIMUM 

NTS 

NOT TO SCALE 

OS&Y 

OUTSIDE SCREW & YOKE 

PLBG 

PLUMBING 

PSI 

POUNDS PER SQUARE INCH 

RCV 

RISER CONTROL VALVE 

RISE 

PIPE RISING BETWEEN FLOORS 

RM 

ROOM 

SPEC 

SPECIFICATIONS 

SPR, SP 

SPDR 

SB 

TS 

SPRINKLER 

SPRINKLER DRAIN 

SLEEVED BEEM CUT. 

TAMPER SWITCH 

TYP 

TYPICAL 

UP 

PIPE RISING THROUGH FLOOR 

V 

VICTAULIC 

W/ WITH 


1. CONTRACTOR SHALL CHECK AND VERIFY THE EXACT LOCATION OF ALL PIPE 

PENETRATIONS AND MAKE CERTAIN THERE ARE NO OBSTRUCTIONS AND 

INTERFERENCES. 

2. CONTRACTOR SHALL REFER TO AND COORDINATE WITH 

ARCHITECTURAL/STRUCTURAL DRAWINGS AND WORK FOR EXACT LOCATION OF 

ALL FIRE PROTECTION PIPING/FHV. 

3. ALL PIPES PENETRATED THROUGH WALLS AND FLOORS SHALL BE PROVIDED WITH 

REQUIRED OPENINGS, SLEEVES, SEALS AND PACKINGS. REFER TO STRUCTURAL 

DRAWINGS FOR CONCRETE PADS. 

4. FIRE PROTECTION: REMOVAL AND RECONNECTION OF EXISTING PIPING MUST BE 

DONE BY A LICENSED FIRE PROTECTION CONTRACTOR AND FILED WITH DOB 

AS THE FIRE PROTECTION WORK TYPE AS PER NYCPC. 

5. FIRE PROTECTION DEMOLITION SHALL BE COORDINATED WITH THE PROJECT 

MANAGER. 

6. CONTRACTOR SHALL COORDINATE ALL SHUTDOWNS WITH COLLEGE OPERATING STAFF 

AS PER SPECIFICATION SECTION 211313 (WET PIPE SPRINKLER) 

15. PROTECTION REQUIREMENTS FOR COMMODITIES SHALL BE IN ACCORDACNE WITH SEC. 5.6.1.2 OF NFPA 13&2002. 

16. REQUIREMENTS FOR CORRECT USE OF SPRINKLER SYSTEM COMPONENTS SHALL COMPLY WITH CHAPTER 6 OF NFPA 13&2002. 

17. THE K&FACTOR, RELATIVE DISCHARGE, AND MARKING IDENTIFICATION FOR SPRINKLERS HAVING DIFFERENT OFFICE SIZES SHALL 

BE IN ACCORDANCE WITH TABLE 6.2.3.1 OF NFPA 13&2002. 

18. LARGE DROP AND ESFR SPRINKLERS SHALL HAVE A MINIMUM NOMINAL K&FACTOR OF 11.2 WITH SEC. 6.2.3.5 OF NFPA 13&2002. 

19. AUTOMATIC SPRINKLERS SHALL HAVE THEIR FRAME DEFLECTOR COATING MATERIALS, OR LIQUID BULB COLORED 

IN ACCORDANCE WITH THE REQUIREMENTS OF TABLE 6.2.5.1 OF NFPA 13&2002. 

20. LISTED CORROSION RESISTANT SPRINKLER SHALL BE INSTALLED IN LOCATIONS WHERE CHEMICALS, MOISTURE, OR OTHER 

CORROSIVE VAPORS SUFFICIENT TO CAUSE CORROSION OF SUCH DEVICES EXIST WITH SEC. 6.2.6.1 OF NFPA 13&2002. 

21. ALL CONTROL, DRUM, AND TEST CONNECTION VALVES SHALL BE PROVIDED WITH PERMANENTLY MARKED WEATHERPROOF 

METAL OR ACID PLASTIC IDENTIFICATION SIGNS. SEC. 6.7.4.1 OF NFPA 13&2002. 

22. THE MAXIMUM FLOOR AREA OR ANY ONE FLOOR TO BE PROTECTED BY A SINGLE RISER FROM A CONTROL VALVE AND ALARM DEVICE SHALL 

COMPLY WITH SEC. 8.2.1 OF NFPA 13&2002. 

23. WHERE CIRCUMSTANCES REQUIRE THE USE OF OTHER THAN ORDINARY TEMPERATURE&RATED SPRINKLERS, STANDARD RESPONSE 

SPRINKLERS SHALL BE PERMITTED TO BE USED SEC. 8.3.3 OF NFPA 13&2002. 

24. WHEN EXISTING LIGHT HAZARD SYSTEMS ARE CONVERTED TO USE QUICK&RESPONSE OR RESIDENTIAL SPRINKLERS ALL SPRINKLERS IN A 

COMPARTMENTED SPACE SHALL BE CHANGED. SEC. 8.3.3.4 OF NFPA 13&2002. 

25. SPRINKLERS SHALL BE LOCATED, SPACED AND POSITIONED IN ACCORDANCE WITH THE REQUIREMENTS OF SECTION 8.5 OF NFPA 13&2002. 

26. PROTECTION AREAS AND MAXIMUM SPACING FOR EACH HAZARD SHALL COMPLY WITH TABLE B.B.2.2.1 (A) (B) (C) (D) OF NFPA 13&2002. 

27. REQUIREMENTS OF STAGES AREA PROTECTION SHALL COMPLY WITH SEC. 8.14.15 OF NFPA 13&2002. 

28. DRAIN CONNECTIONS FOR SYSTEMS SUPPLY RISERS SHALL BE SIZED AS SHOWN IN TABLE 8.15.2.4.2 OF APPENDIX Q&NYC BUILDING 

CODE. 

29. TYPES OF HANGERS SHALL BE IN ACCORDANCE WITH THE REQUIREMENT OF SEC. 9.1 OF NFPA 13&2002. 

30. MAXIMUM DISTANCE BETWEEN HANGERS SHALL BE IN COMPLIANCE WITH TABLE 9.2.2.1 OF NFPA 13&2002. 

TYPE: UPRIGHT OR PENDENT QUICK RESPONSE 

ORIFICE SIZE: 1/2" TEMPERATURE RATING: 

ORDINARY 165° F 

THE SPRINKLER SYSTEM SHALL BE HYDRAULICALLY CALCULATED TO 

MEET THE FOLLOWING CRITERIA IN ACCORDANCE WITH THE NEW YORK 

CITY BUILDING DEPARTMENT AND NFPA STANDARD #13: 

OCCUPANCY: 

AREA OF APPLICATION: 

DENSITY: 

COVERAGE PER SPRINKLER: 

# OF SPRINKLER CALCULATED: 

MINIMUM FLOW FOR ANY SPRINKLER HEAD: 

HYDRAULIC CALCULATION RESULTS: SECOND FLOOR 

WATER FLOW REQUIRED: 277.30 GPM 

REQUIRED PRESSURE: 43.80 PSI 

HYDRANT FLOW TEST DATA 

LIGHT HAZARD 

1,500 SQ. FT. 

0.10 GPM/SQ. FT. 

VARIES (225 SQ. FT. MAX) 

16 

15 GPM 

LOCATION: 1ST HYDRANT ON MELBOURNE AVENUE WEST OF 150TH STREET 

TEST DATE: 8/13/2012 AT 8:50 AM 

TEST DATA: 

FLOW TEST =1000 GPM 

STATIC PRESSURE = 55 PSI 

RESIDUAL PRESSURE = 52 PSI 

1 

SEALS 





66&60 Kissena Boulevard 


31. THE WATER SUPPLY FOR SPRINKLERS SHALL BE DETERMINED BY DENSITY/AREA CURVE, FIGURE 11.2.3.1.5 OF NFPA 13&2002. 

32. HYDRAULIC DESIGN AREA REDUCTION FOR QUICK RESPONSE SPRINKLERS SHALL COMPLY WITH FIGURE 11.2.3.2.3.1 OF NFPA 13&2002. 

APPLICABLE BUILDING CODES 

33. TYPE OF SPRINKLER HEAD IN GENERAL STORAGE SHALL COMPLY WITH SEC. 11.2.3.8 OF NFPA 13&2002. 

34. MINIMUM OPERATING PRESSURE OF ANY SPRINKLER SHALL BE 7 PSI SEC. 14.4.4.6.1 OF NFPA 13&2002. 

35. NUMBER OF WATER SUPPLY FOR SPRINKLER SYSTEM SHALL COMPLY WITH SEC. 15.1.1 OF NFPA 13&2002 AND APPENDIX Q OF NYC BD. 

THE FOLLOWING NOTES SHALL APPLY THROUGHTOUT: 

1. WORK SHALL BE EXECUTED IN FULL COMPLIANCE WITH 

THE APPLICABLE PROVISIONS OF ALL LAWS, BY&LAWS, STATUTES, 

ORDINANCES, CODES, RULES, REGULATIONS AND LAWFUL 

ORDERS OF PUBLIC AUTHORITIES BEARING ON THE 

PERFORMANCE AND EXECUTION OF THE WORK. 

2. THE WORK SHALL COMPLY WITH THE REQUIREMENTS 

OF THE FOLLOWING CODES AND STANDARDS. 

A. NEW YORK UNIFORM CONSTRUCTION CODE AND ICC/ANSI 117.1 

B.NFPA 13&2002 AND APPENDIX Q OF NYC BD. 

1 9.13.12 ADDENDUM #1 



PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 

No. 2115419 


K.ROBINSON 

L.MATLICK 


A 

C. 2008 BUILDING CODE OF THE CITY OF NEW YORK. 

D. FEDERAL STATE / LOCAL AUTHORITIES HAVING JURISDIICTION. 

1 2 3 4 5 

SHEET TITLE 

SPRINKLER 

NOTES 

SYMBOLS AND 

ABBREVIATIONS 

FP&001.00 

25 

of 65 

9/13/2012 9:56:14 AM


DWG. FP101.00(091312) 

SECOND FLOOR PLAN FIRE PROTECTION 




1 

2 3 4 5 

D 

14 13' 13 12 

11 10 10' 9 8 7' 7 6 

AREA OF APPLICATION 

.10GPM / 1500SQ FT. 

LIGHT HAZARD 

MOST REMOTE AREA 

1 2 

Biology Lab 

B237 

1 1/4" SPR 

1 1/4" SPR 

1 1/4" SPR 

20 

1 1/4" SPR 

21 

31 

5 4 3 2 

22 

23 

4" SPR 

2" SPR 

1 

4 3 

1 1/4" SPR 

1 1/2" SPR 

10 9 

1 1/4" SPR 

8 

PHYSICS 

B215 

13' # 4 3/32" 

1 1/4" SPR 

7 

H 

I 






CONSULTANTS 

ENVIRONMENTAL 




1 1/4" SPR 

5 6 

1 1/4" SPR 

11 12 

35 

1 1/4" SPR 

Biology Lab 

B241 

24 

4" SPR 

2" SPR 

4" SPR 

16 1 1/2" SPR 15 

34 

30 29 

33 

28 

1 1/4" SPR 

14 

32 

Preparation room 

B211 

1 1/4" SPR 

13 

12' # 0" 

J 

K 

t 973#240#1800 





t 914#686#7102 

1 1/4" SPR 1 1/4" SPR 1 1/4" SPR 1 1/4" SPR 

C 

Office 

B209 

Corridor 

C003 

L 

Corridor 

C001 

1 1/4" SPR 1 1/4" SPR 

4" SPR 

1 1/4" SPR 

1 1/4" SPR 

Office 

B207 

1 1/4" SPR 

Biology Lab 

B243 

1 1/4" SPR 

4" SPR 

1 1/4" SPR 

1 1/4" SPR 

1 1/4" SPR 

1 1/4" SPR 

M 

M' 

1 1/4" SPR 


B203 

N 

SEALS 

4" SPR 

1 1/4" SPR 

1 1/4" SPR 

1 1/4" SPR 

1 1/4" SPR 

1 1/4" SPR 

Biology Lab 

1 1/4" SPR 

O 

1 1/4" SPR 

B245 

1 1/4" SPR 

4" SPR 

1 1/4" SPR 

1 1/4" SPR 

O' 

B 

24A 

24A 

4" SPR 

P 


4" SPR 



4" SPR 

4"SPR.DN. 

Q 


66#60 Kissena Boulevard 


1 1/4" SPR 

1 1/4" SPR 

25 

25 

3" SPR 

1 1/4" SPR 

1 1/4" SPR 



A 

Biology Lab 

D231 

1 1/4" SPR 

1 1/4" SPR 

3" SPR 

1 1/4" SPR 

3" SPR 

R 

S 

E 

A 

C 

B 


PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 

SHEET TITLE 

No. 2115419 


K.ROBINSON 

L.MATLICK 


FIRE PROTECTION SECOND 

FLOOR PLAN 

1/8" = 1'#0" 

8' 

1 2 3 4 5 

1 1/4" SPR 

Prep. Room 

D231A 

1 1/4" SPR 

T 

D 

KEY PLAN 

SECOND FLOOR 

PLAN FIRE 

PROTECTION 

FP#101.00 

9/13/2012 9:15:42 AM


DWG. P001.00(091312) 

PLUMBING NOTES, SYMBOLS AND 

ABBREVIATIONS 




1 

2 3 4 5 

D 






CONSULTANTS 

ADA 

AFF 

CL OR CL 

CLG 

CO 

CONT 

LIST OF ABBREVIATIONS 

AMERICAN DISABILITIES ACT 

ABOVE FINISH FLOOR 

CENTER LINE 

CEILING 

CLEAN OUT 

CONTINUATION 

CW 

HW 

LG 

LW 

LWV 

CA 

LIST OF SYMBOLS 

COLD WATER CW 

HOT WATER HW 

LAB GAS LG 

LAB WASTE LW 

LAB WASTE VENT LWV 

COMPRESSED AIR CA 


1. ALL GAS, VENT, HOT AND COLD WATER PIPING ARE AT CEILING OR IN 

HUNG CEILING, EXCEPT IN PIPE SPACES OR WHERE OTHERWISE 

NOTED. 

2. CONTRACTOR SHALL CHECK AND VERIFY THE EXACT LOCATION OF ALL 

PIPE PENETRATIONS AND MAKE CERTAIN THERE ARE NO OBSTRUCTIONS 

AND INTERFERENCES. 

3. CONTRACTOR SHALL REFER TO AND COORDINATE WITH ARCHITECTURAL 

DRAWINGS AND WORK FOR EXACT LOCATION OF ALL PLUMBING 

FIXTURES. 

4. ALL PIPES PENETRATED THROUGH WALLS AND FLOORS SHALL BE 

PROVIDED WITH REQUIRED OPENINGS, SLEEVES, SEALS AND PACKINGS. 

REFER TO STRUCTURAL DRAWINGS FOR CONCRETE PADS. 

BUILDING DEPARTMENT PLUMBING NOTES 

ALL PLUMBING WORK SHALL MEET THE REQUIREMENTS OF TITLE 28 NEW YORK CITY 

PLUMBING CODE (NYCPC) AND NEW YORK CITY FUEL GAS CODE (NYCFC). 

1. PROTECTION OF PIPING AS OUTLINED IN SECTION PC 305 SHALL BE PROVIDED 

AS REQUIRED. 

2. ALL PIPING AND MATERIALS SHALL BE AS DIRECTED IN SECTION PC 605. 

3. PIPING JOINTS AND CONNECTIONS SHALL BE AS APPROVED IN SECTION PC 605. 

4. CONSTRUCTION, QUANTITIES, DEVICES, FIXTURES, FAUCETS, VALVES AND 

FACILITIES FOR THE DISABLED SHALL BE AS OUTLINED IN SECTION PC 404. 

5. TRAPS AND CLEANOUTS SHALL BE AS PER SECTION PC 1002 AND PC 708 

ACCORDINGLY. 

ENVIRONMENTAL 




t 9732401800 





t 9146867102 

C 

CU FT 

CW 

DIA 

DIM 

DN 

DROP (DR) 

DWG 

DI 

DW 

EEW 

EL 

EMS 

FD 

FIN FL 

GPM 

HW 

CUBIC FEET 

COLD WATER 

DIAMETER 

DIMENSION 

PIPE DOWN THRU FLOOR 

PIPE DROPPING BETWEEN FLOORS 

DRAWING 

DEIONIZED WATER 

DISH WASHER 

EMERGENCY EYE WASH 

ELEVATION 

EMERGENCY SHOWER 

FLOOR DRAIN 

FINISHED FLOOR 

GALLON PER MINUTE 

HOT WATER 

VA 

FD 

VACUUM VA 

PIPE UP OR RISE 

PIPE DN OR DROP 

CAP 

CLEANOUT CO 

WALL CLEANOUT WCO 

EXISTING PIPING 

DEMOLITION (EXISTING BE REMOVED) 

SHUT OFF VALVE (GATE 

OR BUTTERFLY) 

CHECK VALVE 

STOP SHUTOFF VALVE (BALL ) 

FLOOR DRAIN FD 

POINT OF NEW CONNECTION 

POINT OF DISCONNECT 

5. PLUMBING: REMOVAL AND RECONNECTION OF SANITARY FIXTURES MUST 

BE DONE BY A LICENSED MASTER PLUMBER AND FILED WITH DOB AS 

THE PLUMBING WORK TYPE AS PER NYCPC 2008. 

6. PLUMBING DEMOLITION SHALL BE COORDINATED BETWEEN BUILDING 

FACILITIES, GENERAL CONTRACTOR AND ALL TRADES ON THIS PROJECT. 

7. PROVIDE DRAINS AT ALL LOW POINTS 

8. PROVIDE VENTS AT ALL HIGH POINTS 

9. ALL PLUMBING FIXTURES SHALL BE INSTALLED BY THE PLUMBING 

CONTRACTOR. SCIENCE SINKS ARE PROVIDED WITH THE MILL WORK 

REFER TO ARCHITECTURAL DRAWINGS FOR THIS FIXTURES. 

10. PLUMBING CONTRACTOR SHALL PROVIDE TEMPORARY SERVICE TO KEEP 

EQUIPMENT THAT IS NOT IN CONTRACT ON LINE. PLUMBING CONTRACTOR 

SHALL FIELD VERIFY THE LOCATIONS OF THESE EXISTING EQUIPMENT AND 

NOTIFY THE COLLEGE PRIOR TO ANY SHUTDOWN OF SYSTEM. 

11. IF THE COLLEGE GRANTS SHUTDOWNS ONLY IN OFF HOURS, THERE SHALL BE 

NO PREMIUM TIME ADDITIONS TO THE CONTRACT. 

12. CONTRACTOR SHALL VERIFY THAT ALL RISER CONTROL VALVE FOR DOMESTIC 

WATER, GAS, COMPRESSED AIR AND VACUUM PIPING ARE FULLY OPERABLE 

PRIOR TO ANY AND ALL RISER SHUT DOWN FOR THE PURPOSE OF DEMOLITION 

AND OR NEW WORK. IF RISER CONTROL VALVES CANNOT SHUTOFF AND ISOLATE 

THE DESIGNATED RISERS COMPLETELY. THE CONTRACTOR MUST PROVIDE 

OPTIONAL PRICE FOR THE REMOVAL AND REPLACEMENT OF EACH VALVE THAT IS 

INOPERABLE. THIS SHOULD BE ADDED IN THE BID COST. 

PLUMBING DEMOLITION NOTES 

1. ALL EXISTING SYSTEMS SHALL BE LEFT IN PERFECT WORKING ORDER 

UPON COMPLETION OF ALL NEW WORK. 

6. CONSTRUCTION AND SPACING OF HANGERS AND SUPPORTS SHALL BE AS 

DIRECTED IN SECTION PC 308. 

7. WATER SUPPLY SYSTEM, VALVES, TESTS SHALL BE AS DIRECTED IN 

CHAPTER 6. VALVES SHALL BE PROVIDED AT RISERS AND ELSEWHERE AS PER 

SECTION PC 606. 

8. SANITARY DRAINAGE PIPING, SIZING, GRADING AND OFFSETS SHALL BE AS 

OUTLINED IN CHAPTER 7. 

9. VENT SIZING, GRADING, CONNECTIONS, LOCATIONS AND OFFSETS SHALL BE 

AS DIRECTED IN CHAPTER 9. 

10. ALL PLUMBING FIXTURES SHALL COMPLY WITH LOCAL LAW 86/2005 

GREEN BUILDING STANDARDS OR CHAPTER 4 SECTION PC 401.3 

WATER CONSERVATION. 

11. MATERIALS, ASSEMBLIES, FORMS AND METHODS OF CONSTRUCTION SHALL 

BE APPROVED BY BOARD OF STANDARDS AND APPEALS OF THE CITY OF 

NEW YORK AND CONTRACTOR SHALL PROVIDE OTCR NUMBER OF 

SAME PURCHASED AND APPROVED FOR INSTALLATION. 

12. CONTRACTOR SHALL RETAIN A LICENSED PROFESSIONAL ENGINEER TO 

PERFORM ALL REQUIRED SPECIAL INSPECTIONS. SAME SHALL BE 

FILED WITH THE DEPARTMENT OF BUILDING. 

13. ALL HOT WATER PIPING TO BE PROVIDED WITH 1 INCH INSULATION 

14. GAS PIPING, MATERIAL, SIZING, OFFSET AND INSTALLATION SHALL 

BE AS OUTLINED IN THE NYC FUEL GAS CODE 

SEALS 

B 

IM 

IW 

LG 

LV 

LW 

ICE MAKER 

INDIRECT WASTE 

LABORATORY NATURAL GAS 

LABORATORY VACUUM 

LABORATORY (ACID) WASTE 

P 

X 

1 

P 

PLBG RISER 

DETAIL NUMBER 

2. EXACT SIZES AND LOCATIONS OF ALL EXISTING PIPING SHALL BE 

VERIFIED ON THE JOB. 

3. NO REMOVED EXISTING PIPING SHALL BE REUSED UNLESS OTHERWISE 

INDICATED. 

4. THE CONTRACTOR SHALL SUBMIT TO THE ARCHITECT FOR APPROVAL, 

PRIOR TO INSTALLATION, COMPLETE LAYOUT DRAWINGS INDICATING ALL 

PIPING SIZING. 

5. ALL EXISTING PIPING NOT SPECIFICALLY INDICATED TO BE REMOVED 

SHALL REMAIN AS IS. 




LWV 

MGCV 

MTD 

NTS 

PLBG 

PSI 

RISE 

RM 

S, SAN 

ST 

TMV 

TW 

LABORATORY (ACID) WASTE VENT 

MASTER GAS CONTROL VALVE 

MOUNTED 


PLUMBING 

POUND SQUARE PER INCH 

PIPE RISING BETWEEN FLOORS 

ROOM 

SANITARY 

SEDIMENT TRAP 

THERMOSTATIC MIXING VALVE 

TEMPERED WATER 

6. ANY AND ALL REQUIRED DEMOLITION WORK TO BE PERFORMED ABOVE 

EXISTING SUSPENDED CEILINGS AND FURRED OUT WALLS SHALL BE DONE 

AT THE TIME WHEN THE EXISTING CEILINGS AND FURRED OUT WALLS ARE 

REMOVED BY THE GENERAL CONTRACTOR. 

7. ALL EQUIPMENT AND INSTALLATIONS MUST BE EQUAL TO THE STANDARDS 

OF THE BASE BUILDING. ANY DEVIATION FROM BUILDING STANDARDS WILL 

BE PERMITTED ONLY IF INDICATED OR SPECIFIED ON THESE PLANS AND 

SPECIFICATIONS, AND APPROVED. 

8. TO ENSURE CONTINUOUS OPERATION, MAKE ALL NECESSARY TEMPORARY 

CONNECTIONS BETWEEN NEW AND EXISTING WORK. ALL COSTS 

RESULTING FROM TEMPORARY SHUTDOWNS SHALL BE BORNE BY THIS 

CONTRACTOR. 

9. EXISTING PIPING SHALL BE CUT, REMOVED AND CAPPED AS INDICATED 

ON DRAWINGS, UNLESS OTHERWISE NOTED. 

10. DURING CONSTRUCTION. STANDPIPE SYSTEMS REQUIRED DURING 

CONSTRUCTION, ALTERATION AND DEMOLITION OPERATIONS SHALL BE 

PROVIDED IN ACCORDANCE WITH BUILDING CODE OF THE CITY OF NEW 

YORK 2008, SECTION 3303.8 

11. ALL OPENINGS CREATED AS A RESULT OF THE DEMOLITION WORK SHALL BE 

FILLED IN TO MATCH EXISTING CONSTRUCTION BY PLUMBING CONTRACTOR. 

1 







PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 

2115419 


K.Robinson 

L.Matlick 


A 

TYP 

TYPICAL 

UP 

PIPE RISING THRU FLOOR 

1 2 3 4 5 

SHEET TITLE 

PLUMBING 

NOTES, 

SYMBOLS AND 

ABBREVIATIONS 

P001.00 

37 

of 65 

9/13/2012 9:11:29 AM


DWG. M101.00(091312) 

2 ND FLOOR MECHANICAL DEMOLITION 




1 

2 3 4 5 

DEMOLITION GENERAL NOTES 


D 

1 

1. COORDINATE ALL DEMOLITION WORK AND ANY NECESSARY 

SYSTEM SHUTDOWNS WITH THE GENERAL CONTRACTOR AND 

OWNER. 

2. ALL EQUIPMENT AND DEVICES NOT INDCATED TO BE 

DEMOLISHED ARE EXISTING TO REMAIN. 

3. ALL OPENINGS CREATED AS A RESULT OF THE DEMOLITION 

WORK SHALL BE FILLED&IN TO MATCH EXISTING 

CONSTRUCTION BY MECHANICAL CONTRACTOR. 

4. ALL WORK ON THIS DRAWING BY MECHANICAL CONTRACTOR, 

UNLESS OTHERWISE NOTED. 

5. DEMOLISH ALL PNEUMATIC TUBING, MECHANICAL CONTROL 

PANELS AND ASSOCIATED CONTROL DEVICES WITHIN B237, 

B241, B243, B245, B211, B203, D231, D231A. 





CONSULTANTS 

ENVIRONMENTAL 




t 973&240&1800 

C 

7 6 

300 CFM 

CORRIDOR 

C001 

20x5 

LAB 

B237 

LAB 

B241 

13ø 

14ø 

13ø 

14ø 

250 CFM 

(TYP FOR 6) 

250 CFM 

(TYP FOR 6) 

5 

24X14 UP, 24X12 DN (ETR) 

18X16 UP (ETR) 

1"ø LPC 

1 1/4"ø LPS 

12ø 

2&1/2" LPS UP, 3" LPS DN (ETR) 

3 

1&1/2" LPC UP, DN (ETR) 

1"ø LPC 

1 1/4"ø LPS 

3 


4 

18ø 

18x24 

16ø 

16ø 

12ø 

1400 CFM 

40x18 

40x18 

1500 CFM 

3 

3 

18x24 

3 

16x10 

120 CFM 

PHYSICS 

B215 

3 

PREP RM. 

7ø 

125 CFM 

B211 

575 CFM 

14ø 

10ø 

OFFICE 

B209 

10ø 

16x10 

2 

CORRIDOR 

C003 

14Ø RETURN AIR DUCT (ETR) 

10Ø TRANSFER DUCT (ETR) 

1 

2 18X18 TRANSFER 

DUCT 

3 

24X36 UP, 24X20 DN (ETR) 

H' 

H 

SUPPLY AIR VAV AND DUCTWORK (ETR) 


DUCT 

1 

4 

20X22 UP, 20X18 DN (ETR) 

13Ø RETURN DUCT (ETR) 


I 

J' 

J 

K 

D233 

5 

4 

BIOLOGY LAB 

D231 

300 CFM 

30x6 

3 

CORRIDOR 

C002 

350 CFM 

(TYP FOR 4) 

P 

Q 

1 

2 

3 

4 

DEMOLITION KEY NOTES 

AIRFLOWS SHOWN IN SPACES (OUTSIDE OF THE PROJECT 

AREA) ARE EXISTING QUANTITIES OBTAINED FROM AS&BUILT 

DOCUMENTS. PRIOR TO CONSTRUCTION, THE CONTRACTOR 

SHALL TAKE AIRFLOW MEASUREMENTS AT EACH INDICATED 

LOCATION AND PREPARE A REPORT FOR THE ENGINEER'S 

REVIEW BEFORE AND AFTER CONSTRUCTION. 

DEMOLISH TRANSFER DUCT AND ASSOCIATED GRILLES. FILL 

AND PATCH WALL TO MATCH EXISTING. 

PROVIDE TEMPORARY CAP FOR DUCTWORK AND/OR PIPING 

AT DISCONNECTION POINT TO PREVENT LEAKAGE FROM 

SYSTEM AND TO PROTECT DUCTWORK AND PIPING THAT IS 

EXISTING TO REMAIN 

CUT AND CAP EXISTING TRANSFER DUCT ON CORRIDOR SIDE 

OF LAB PREP ROOM WALL. FILL AND PATCH WALL TO 

MATCH EXISTING. 





t 914&686&7102 

SEALS 

B 

A 

7' 

300 CFM 

20x5 

LAB 

B243 

LAB 

B245 

250 CFM 

(TYP FOR 6) 

14ø 

14ø 

1 1/4"ø LPS 

6" LPS UP, 8" LPS DN (ETR) 

4" LPC UP, DN (ETR) 

250 CFM 

(TYP FOR 6) 

13ø 

13ø 

1"ø LPC 

18X20 UP, 18X10 DN (ETR) 

3 

3 

3 

3 

1"ø LPC 

1 1/4"ø LPS 

12ø 

18ø 

18x24 

16ø 

16ø 

1200 CFM 

40x18 

40x18 

1200 CFM 

2ND FL. AREA B & DEMO PLAN 

1/8" = 1'&0" 

12ø 

8ø 

18x24 

12ø 

3 

OFFICE 

B207 

PREP RM. 

12ø 

450 CFM 

720 CFM 

B203 

7ø 

120 CFM 

28X36 UP, 20X36 DN (ETR) 

SUPPLY AIR VAV AND 

DUCTWORK (ETR) 

16ø 

390 CFM 

OFFICE 

B201 

120 CFM 

14X14 UP, 14X12 DN (ETR) 

12ø 

12ø 

16x10 

RETURN AIR DUCT AND REGISTER (ETR) 

1 


DUCT 

2 

L 

M 

M' 

N 

EXISTING MECHANICAL CONNECTIONS TO 

EXISTING FUME HOOD TO BE REMOVED 

BY MECHANICAL CONTRACTOR 

2 

30X6 TRANSFER 

DUCT 

30X6 TRANSFER 

DUCT 


DUCT 

1 

3 

4 


O 

O' 

P' 

P 

EXISTING MECHANICAL CONNECTIONS TO 

EXISTING FUME HOOD TO BE REMOVED 

BY MECHANICAL CONTRACTOR 

3 

12ø 

16X18 UP, DN (ETR) 


20ø 

14ø 

34x16 

40x10 

17ø 

12ø 

3 3 

D223 

14ø 

34x16 

PREP RM 

D231A 

1 1/4"ø LPS 

1"ø LPC 

3 

R 

S 

T 

2&1/2" LPS UP, 3" LPS DN (ETR) 

1&1/2" LPC UP, DN (ETR) 

10X32 UP, 10X22 DN (ETR) 

20X44 UP, 20X20 DN (ETR) 

2ND FL. AREA D & DEMO PLAN 

1 2 3 4 5 

1/8" = 1'&0" 

1 

E 

A 

C 

D 

KEY PLAN 

B 





66&60 Kissena Boulevard 


1 9&13&12 ADDENDUM #1 



PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 


JOHN NADON 


SHEET TITLE 

2ND FLOOR 

MECHANICAL & 

DEMOLITION 

M&101.00 

43 

of 65 

2115419 

FRANK TIERNO 

9/12/2012 11:25:03 AM


DWG. E001.00(091312) 

ELECTRICAL SYMBOL LIST, ABBREVIATIONS AND 

NOTES 




1 

2 3 4 5 


D 

SYMBOL 

J J 

a 

D 

J 

SYMBOL LIST 

JUNCTION/SPLICE BOX, SIZE AS REQUIRED. 

DESCRIPTION 

LIGHTING AND POWER PANELBOARD, RECESSED MOUNTED IN WALL. 

SINGLE POLE TOGGLE SWITCH. SUBSCRIPT DENOTES FIXTURES CONTROLLED/RECEPTACLES 

CONTROLLED SHOWN ON POWER PLANS. '3' INDICATES THREE!WAY SWITCH. 'D' INDICATES 

DIMMER SWITCH. 'OC' INDICATES OCCUPANCY SENSOR. 

LOWER CASE LETTERS INDICATE SWITCH DESIGNATION. 

DUPLEX THREE WIRE GROUNDED RECEPTACLE, 20A, 125V. 

"GFI" INDICATES GROUND FAULT INTERRUPTING TYPE. 

QUAD RECEPTACLE, THREE WIRE GROUNDED 20A, 125V. 

SIMPLEX RECEPTACLE, THREE WIRE GROUNDED 20A, 125V. 

SYMBOL 

AP 

W 

C 

TELECOM SYMBOL LIST 

DESCRIPTION 

WALL MOUNTED TELEPHONE OUTLET FOR STANDARD WALL INSTRUMENT, WITH SINGLE JACK 

INSTALLED IN METAL LOCK BOX. CAT 6 CABLES. MOUNT AT 4'!0" A.F.F., U.O.N. 

SURFACE MOUNTED DATA OUTLET WITH DUPLEX JACK LABELED "DATA", MOUNTED AT 18" A.F.F. IN WALL, 

SURFACE RACEWAY, OR ON PEDESTAL. CAT 6 CABLES. 

SINGLE DATA JACK FOR WIRELESS ACCESS POINT DEVICE MOUNTED ABOVE CEILING 

WIDE ANGLE PASSIVE INFRARED MOTION DETECTOR WITH GUARD. 

CLOCK, MOUNTED AT 7'!6". PROVIDE CLOCK OF SAME TYPE AS EXISTING SYSTEM, AND FULLY COMPATIBLE. 


1. ALL WORK SHALL BE PERFORMED IN ACCORDANCE WITH REQUIREMENTS OF RELEVANT 

SPECIFICATIONS AND CODES. 

2. INSTALLATION OF ELECTRICAL DEVICES INCLUDING RACEWAYS AND JUNCTION BOXES ARE 

SHOWN DIAGRAMMATICALLY. COORDINATE ALL WORK WITH OTHER TRADES TO AVOID 

INTERFERENCE. 

3. ALL WORK SHOWN ON ELECTRICAL DRAWINGS IS THE RESPONSIBILITY OF THE ELECTRICAL 

CONTRACTOR, UNLESS OTHERWISE NOTED. 

4. COORDINATE WITH OTHER TRADES FOR EXACT LOCATIONS OF MOTORS AND EQUIPMENT, IN 

ORDER TO AVOID INTERFERENCE. 

5. CONDUIT HOMERUNS NOT OTHERWISE MARKED SHALL BE CONSIDERED 2#12 AND 1#12 GROUND 

IN 3/4" MINIMUM CONDUIT. 

6. CONTRACTOR SHALL COORDINATE ALL RECEPTACLE MOUNTING HEIGHTS WITH APPROVED 

CASEWORK SHOP DRAWINGS PRIOR TO INSTALLATION OF AFFECTED RECEPTACLES. 

7. THIS CONTRACTOR SHALL FURNISH, INSTALL AND SIZE ALL SLEEVES, HOLES, CORES, PATCHING, 

SLOTS, ANCHORS, BRACKETS, SUPPORTS, JUNCTION BOXES, PULL BOXES, AND OTHER 

APPURTENANCES NECESSARY TO EXECUTE THE CONTRACT DOCUMENTS COMPLETELY. SOME OF 

THESE ITEMS MAY BE SHOWN ON THE DRAWINGS FOR CLARITY OR DESIGN PREFERENCE. 

HOWEVER, NOT ALL OF THE ITEMS NECESSARY FOR COMPLETE EXECUTION AND INSTALLATION 

ARE SHOWN. 





CONSULTANTS 

ENVIRONMENTAL 




t 973!240!1800 





t 914!686!7102 

C 

OS 

PP 

CR 

G 

DC 

DESIGNATION 

R 

SURFACE MOUNTED PEDESTAL 

WALL MOUNTED SURFACE RECEPTACLE/DATA DUAL RACEWAY. 

MANUFACTURED BY WIREMOLD CO. MODEL# WIREMOLD V!4000 OR EQUAL. 

RACEWAY HOUSES 10!20 AMP. DUPLEX RECEPTACLES, TWO (2) DATA 

JACKS 

LOW VOLTAGE DUAL TECHNOLOGY (PASSIVE INFRARED AND ULTRASONIC) 

OCCUPANCY SENSOR, CEILING MOUNTED, RECTANGULAR PATTERN COVERAGE. 

POWER PACK WORKING IN CONJUNCTION WITH LOW VOLTAGE OCCUPANCY SENSORS. 

CARD READER. MOUNT AT 3'!6" A.F.F. 

GAS SHUT OFF SWITCH. MOUNT AT 5'!0" A.F.F. 

DOOR CONTACT 

DESIGNATIONS FOR DEMO PLANS 

DESCRIPTION 

SYMBOL WITH SUBSCRIPT "R" INDICATES EXISTING DEVICE TO BE REMOVED. 

APPLICABLE CODES 

1. 2008 NEW YORK CITY BUILDING CODE 

2. 2011 NEW YORK CITY ELECTRICAL CODE 

3. AMERICANS WITH DISABILITIES ACT (ADA) 

4. NATIONAL FIRE PROTECTION ASSOCIATION (N.F.P.A. 72) 

5. FEDERAL STATE / LOCAL AUTHORITIES HAVING JURISDICTION 

ABBREVIATIONS 

A, AMP 

A.F.F. 

A.I.C. 

AWG 

C 

CB 

CM 

DWG 

ELEC 

E.C. 

EM 

FD 

FSD 

G, GND 

G.C. 

GFI 

J, JB 

LTG 

MIN 

MTD 

NTS 

P 

PH 

PNL 

PP 

TYP 

U.O.N. 

V 

VA 

AMPERES 

ABOVE FINISHED FLOOR 

AMPERE INTERRUPTING CAPACITY 

AMERICAN WIRE GAUGE 

CONDUIT 

CIRCUIT BREAKER 

CONSTRUCTION MANAGER 

DRAWING 

ELECTRICAL (EQUIPMENT OR WIRING) 

ELECTRICAL CONTRACTOR 

EMERGENCY 

FIRE DAMPER 

FIRE SMOKE DAMPER 

GROUND 

GENERAL CONTRACTOR 

GROUND FAULT INTERRUPTER 

JUNCTION BOX 

LIGHTING 

MINIMUM 

MOUNTED 


POLE 

PHASE 

PANEL 

POWER PANEL 

TYPICAL 

UNLESS OTHERWISE NOTED 

VOLTS 

VOLT AMPERES 

8. MINIMIZE THE VISUAL IMPACT OF EXPOSED RACEWAYS AND CONDUITS BY CAREFUL SELECTION 

OF ROUTING. SELECT THE ROUTING IN CONCERT WITH THE ARCHITECTURAL DESIGN OF THE 

BUILDING. 

9. UNLESS OTHERWISE NOTED ON FLOOR PLANS OR IN FLOOR PLAN NOTES, SWITCHES SHALL BE 

INSTALLED AT 4'!0" ABOVE FINISHED FLOOR. 

10. APPLICABLE CODES: 

• AMERICANS WITH DISABILITIES ACT (ADA) 

• 2008 NEW YORK CITY BUILDING CODE 

• 2011 NEW YORK CITY ELECTRICAL CODE 

11. CONTRACTOR SHALL PROVIDE ANY TEMPORARY LIGHTING AND POWER REQUIRED DURING THE 

COURSE OF CONSTRUCTION. ALL 15, 20 AND 30 AMP RECEPTACLES USED FOR CONSTRUCTION 

SHALL HAVE GFCI PROTECTION. ALL TEMPORARY WIRING SHALL COMPLY WITH NEC ARTICLE 590. 

12. UNLESS OTHERWISE INDICATED, ALL MOUNTING ELEVATIONS ARE CENTERLINE ELEVATIONS. 

REMOVAL NOTES 

1. EXISTING CONDITIONS INDICATED ON THE CONTRACT DRAWINGS ARE BASED ON FIELD 

OBSERVATIONS AND EXISTING RECORD DRAWINGS. VERIFY EXISTING CONDITIONS IN THE FIELD. 

2. NOTES AND GRAPHICAL REPRESENTATIONS ON THE CONTRACT DRAWINGS SHALL NOT LIMIT THE 

EXTENT OF REMOVALS REQUIRED. PERFORM REMOVALS NECESSARY TO ACHIEVE THE DESIGN 

INTENT. COORDINATE THE EXTENT OF REMOVALS WITH THE OTHER TRADES. 

3. FOR EQUIPMENT AND WIRING DEVICES THAT WILL BE REMOVED, DEENERGIZE AND DISCONNECT. 

REMOVE CONDUITS AND WIRING BACK TO THE SOURCE, U.O.N. 

4. UNLESS OTHERWISE INDICATED, EXISTING SERVICES, SYSTEMS, AND WIRING SERVING EXISTING 

AREAS OUTSIDE OF THE AREA OF CONSTRUCTION SHALL REMAIN OR SHALL BE RELOCATED AS 

REQUIRED TO MAINTAIN OPERATION OF EXISTING SYSTEMS AND AVOID CONFLICT WITH 

CONSTRUCTION. 

5. WHERE EQUIPMENT AND WIRING ARE REQUIRED TO REMAIN IN SERVICE, BUT INTERFERE WITH 

THE ALTERATIONS, RELOCATE AND RECONNECT USING MATERIALS AND STANDARDS OF THIS 

CONTRACT. 

SEALS 

ETR 

SYMBOL WITH SUBSCRIPT 'ETR' INDICATES EXISTING DEVICE TO REMAIN. 

6. USE CAUTION TO PREVENT DAMAGE TO ARCHITECTURAL SURFACES AND MATERIALS THAT ARE 

TO REMAIN. REPAIR OR REPLACE DAMAGED ITEMS. 

B 

RL 

SYMBOL WITH SUBSCRIPT 'RL' INDICATES EXISTING DEVICE TO BE RELOCATED. 

7. UNLESS OTHERWISE INDICATED, TAKE REMOVED MATERIALS FROM THE SITE AND DISPOSE OF IN 

ACCORDANCE WITH APPLICABLE LAWS AND ENVIRONMENTAL REGULATIONS. 

8. ALL OPENINGS CREATED AS A RESULT OF THE DEMOLITION WORK SHALL BE FILLED IN TO MATCH 

EXISTING CONSTRUCTION BY ELECTRICAL CONTRACTOR. 

1 





65!30 Kissena Boulevard 


LIGHTING FIXTURE SCHEDULE 

TYPE DESCRIPTION MANUFACTURER CATALOG NUMBER VOLTAGE VOLT!AMPS 

A 

B 

C 

1'x4' LED RECESSED EPOC FULL 

DISTRUBITION LUMINAIRE 

SUSPENDED 96" T8 FLUORESCENT 

LUMINAIRE WITH LINEAR PRISMATIC LENS 

LED EXIT SIGN WITH EMERGENCY 

BATTERY 

COLUMBIA 

LIGHTING 

LIGHTOLIER 

LIGHTING 

LEPC14!35!22!G!LL!ED!U PROVIDE EMERGENCY 

BATTERY PACK FOR EM FIXTURES 

EYS8LFX232120H4 PROVIDE EMERGENCY 

BATTERY PACK FOR EM FIXTURES 

120 V 43 VA 

120 V 128 VA 

ENCORE LIGHTING LPE!R1!DG 120 V 3 VA 

1 9!13!12 ADDENDUM #1 


ISSUE BLOCK 

COLOR TEMPERATURE OF NEW FLUORESCENT LIGHT FIXTURES SHALL MATCH COLOR TEMPERATURE OF EXISTING FIXTURES. 


PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

2115419 


STEPHANIE AMOH 

JOHN HANNAH 


A 

1 2 3 4 5 

SHEET TITLE 

ELECTRICAL 

SYMBOL LIST, 

ABBREVIATIONS, 

AND NOTES 

E!001.00 

54 

of 65 

9/13/2012 12:40:15 PM


DWG. E100.00(091312) 

2 ND FLOOR LIGHTING PART PLANS DEMO 




3 

1 

2 3 4 5 

D 


1. FOR GENERAL NOTES, REMOVAL NOTES, SYMBOL LIST, AND ABBREVIATIONS, SEE DRAWING 

E+001. 

2. REMOVE AND PROPERLY DISPOSE OF SWITCHES SCHEDULED TO BE REMOVED. REMOVE ALL 

EXISTING LIGHTING FIXTURES AND FLUORESCENT BULBS SCHEDULED TO BE REMOVED, AND 

COORDINATE FOR GENERAL CONTRACTOR TO DISPOSE AS UNIVERSAL WASTE. 

3. REMOVE ASSOCIATED CONDUIT AND BRANCH CIRCUIT WIRING BACK TO THE SUPPLYING 

PANEL(S), U.O.N. 

4. MAINTAIN AND RESTORE, IF INTERRUPTED, ALL CONDUITS AND CONDUCTORS PASSING THROUGH 

RENOVATED AREAS SERVICING UNDISTURBED AREAS. 

5. ALL WORK SHOWN ON THIS DRAWING IS THE RESPONSIBILITY OF THE ELECTRICAL CONTRACTOR, 

U.O.N. 






CONSULTANTS 

ENVIRONMENTAL 




t 973+240+1800 

6 

5 

4 

3 





t 914+686+7102 

EXISTING PENDANT 

MOUNTED FLUORESCENT 

TO BE REMOVED. 

(TYPICAL) 

H' 

C 

H 

R 

R 

G 

R 

R 

R 

R 

R 

R 

R 

LAB 

B237 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

PREP RM. 

B211 

I 

J' 

R 

R 

R 

R 

R 

R 

LAB 

B241 

R 

R 

R 

R 

R 

R 

R 

R 

R 

1 

R 

J 

K 

5 

4 

3 

SEALS 

B 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

LAB 

B243 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

1 

PREP RM. 

B203 

L 

M 

M' 

N 

OC 

1 

R 

R 

R 

R 

Lab 

D231 

R 

R 

R 

R 

R 

EXISTING PENDANT 

MOUNTED FLUORESCENT 

TO BE REMOVED. 

(TYPICAL) 

Q 

R 





65+30 Kissena Boulevard 


A 

R 

R 

R 

R 

R 

R 

R 

R 

R 

LAB 

R 

B245 

2ND FLOOR + AREA B LIGHTING 

DEMO PLAN 

1/8" = 1'+0" 

R 

R 

R 

R 

R 

R 

R 

R 

1 

R 

R 

R 

O 

O' 

P' 

P 

1 2 3 4 5 

1/8" = 1'+0" 

OC 

R 

R 

R 

R 

R 

1 

R 

R 

R 

R 

Prep Room 

D231A 

2ND FLOOR + AREA D LIGHTING 

DEMO PLAN 

S 

E 

A 

C 

D 

KEY PLAN 

B 

1 9+13+12 ADDENDUM #1 



PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 




SHEET TITLE 

2ND FLOOR 

LIGHTING PART 

PLANS + DEMO 

E+100.00 

55 

of 65 

2115419 

JOHN HANNAH 

9/13/2012 12:40:16 PM


DWG. E110.00(091312) 

2 ND FLOOR POWER & LOW VOLTAGE 

PART PLANS DEMO 




1 

2 3 4 5 


D 

6 

5 

4 

3 



E001. 

2. FOR RISER DIAGRAM, SEE DRAWING E600. 

3. REMOVE ASSOCIATED CONDUIT AND BRANCH CIRCUIT WIRING BACK TO THE SUPPLYING 

PANEL(S), U.O.N. 

1 

4. MAINTAIN AND RESTORE, IF INTERRUPTED, ALL CONDUITS AND CONDUCTORS PASSING THROUGH 

RENOVATED AREAS SERVICING UNDISTURBED AREAS. 

5. EXISTING FUME HOOD TO BE REMOVED BY GC. EXISTING ELECTRICAL CONNECTION TO BE 

REMOVED BY EC. 


U.O.N. 

7. DISCONNECT AND REMOVE AIR VALVE CONTROLS AND ASSOCIATED ELECTRICAL DEVICES. TURN 

OVER TO QUEENS COLLEGE FOR REUSE. 

8. EXISTING MECHANICAL EQUIPMENT TO REMAIN SHALL BE DISCONNECTED FROM EXISTING 

POWER PANELS AND RECONNECTED TO NEW PANELS. REUSE EXISTING WIRING TO CIRCUIT TO 

NEW PANELS. 

9. REMOVE EXISTING WALL MOUNTED IDF RACKS AND WIRELESS ACCESS POINTS IN LABS AND PREP 

ROOMS. TURN OVER TO QUEENS COLLEGE FOR REUSE. 





CONSULTANTS 

ENVIRONMENTAL 




t 9732401800 





t 9146867102 

C 

B 

A 

? 

RELOCATE CONDUIT 

TO ACCOMMODATE 

NEW CASEWORK. 

1 

1/8" = 1'0" 

W 

G 

W 

W 

R 

1 

W 

RL 

RL 

RL 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

RL R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

1 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

1 

R 

C 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R R 

LAB 

R 

R 

R 

B237 

R 

R 

ETR 

R 

ETR 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

1 1 LAB 1 

R 

1 

R 

B241 

LAB 

B243 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

RL 

1 1 LAB 1 

B245 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

ETR 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

SEE NOTE 12 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

ETR R R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

R 

J 

J 

R 

AP2N 

R 

ETR 

AP2P 

2ND FLOOR AREA B POWER 

AND LOW VOLTAGE DEMO PLAN 

1 

1 

ETR 

R 

AP2R 

R 

R 

R 

AP2Q 

R 

ETR 

ETR 

ETR 

R R R R 

R 

PROJECTOR 

ETR 

J 

220V 

RECEPTACLE 

R 

1 

R R R 

PREP RM. 

ETR 

B211 

J 

R 


R 


PREP RM. 

ETR 

1 

B203 

R R R R R 

ETR 

ETR 

ETR 

ETR 

ETR 

ETR 

ETR 

H' 

H 

I 

J' 

J 

K 

L 

M 

M' 

N 

O 

O' 

P' 

P 

5 4 3 

ETR 

ETR 

ETR 

ETR 

ETR 

J 

R 

R 

R 

R 

R 

C 

ETR 

ETR 


R 

AP2S R R 

1 

R 

Prep Room 

ETR 

ETR 

R R R R R 

R 

R R R R R R R R R R R R 

Lab 

D231 

R 



1 2 3 4 5 

D231A 

ETR 

R 

R 

ETR 

REMOVE ALL 

ASSOCIATED 

DEVICES AND 

WIRING. 

2ND FLOOR AREA D POWER 

AND LOW VOLTAGE DEMO PLAN 

1/8" = 1'0" 

1 

1 

1 

1 

Q 

R 

S 

10. ALL EXISTING EQUIPMENT FOR PROJECTOR (I.E. PROJECTOR, AV OUTLETS, SPEAKERS, 

CONDUITS, ETC.) SHALL BE REMOVED. 

11. REMOVE ALL DATA DEVICES AND ASSOCIATED WIRING AND CONDUITS, U.O.N. 

12. DISCONNECT AND REMOVE EMERGENCY GAS SHUTOFF EQUIPMENT AND ASSOCIATED 

ELECTRICAL DEVICES. TURN OVER TO QUEENS COLLEGE FOR REUSE. 

E 

A 

C 

D 

KEY PLAN 

1 

B 



PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

SEALS 






1 91312 ADDENDUM #1 


ISSUE BLOCK 




SHEET TITLE 

2ND FLOOR 

POWER & LOW 

VOLTAGE PART 

PLANS DEMO 

E110.00 

56 

of 65 

2115419 

JOHN HANNAH 

9/13/2012 12:53:04 PM


DWG. E130.00(091312) 

2 ND FLOOR POWER & LOW VOLTAGE 

PART PLANS 




1 

2 3 4 5 


D 

5 

4 

3 



E001. 

2. FOR RISER DIAGRAM, SEE DRAWING E600. 

3. FOR PANEL SCHEDULES, SEE DRAWINGS E601 AND E602. 





CONSULTANTS 

C 

B 



CR 

CR 

CR 

J 

C 

G 

W 

1 10 

J 

23 

C 

G 

POWER SUPPLY FOR 

DOOR CONTROLLERS. 

RL 

CONNECT 2 DOORS 

PER SUPPLY. J 22 


DOOR CONTROLLERS. 

CONNECT 2 DOORS 

PER SUPPLY. 


W 

C 

W 

1 

RL AP 

C 

23 

J 

AP 

15 

W 

CR 

17 

16 

Biology Lab 

B241 

Biology Lab 

B245 

19 

18 

21 

48" 

15 5 9 

4 

ETR 

20 

EV4 

J 

ETR FSD 

J 6 

FSD 

7 J 

J 

PPB237 

J 

FSD 

10 

10 10 10 

J 7 

42" 42" 42" 42" 

EV6 

12 15 13 17 

1 

16 14 11 8 J 9 

AP 10 

19 

42" 

J 15 12 17 13 14 16 8 11 


1 

RHC6 SV6 

J SV6B 

SEE NOTE 10 (TYP) 

9 

J 

9 J 

9 

12 15 13 17 16 14 11 8 

3 


FSD 

SV5 13 

7 


J 11 J RHC5 25 J 

RL 

SV6A SEE NOTE 7 (TYP) 

11 

Biology Lab 

9 J 


7 

B237 

J 


AP 

1 


FSD 

B211 ETR 

42" 

5 

10 

8 8 

48" 

9 

4 2 

ETR 

FSD 

J 12 

7 4 7 4 

24 J 

6 J 

SV5A 

9 

4 J 

42" 42" 42" 42" 

PPB241 

11 

ETR 

ETR 

10 15 1 17 16 19 18 21 20 

ETR 

3 

RHC4 

J 

AP 

J 

8 8 

9 

11 SV4 11 


ETR 

15 10 16 17 18 19 20 

21 

EV5 J 11 

4 

42" 

15 

42" 

GFI GFI GFI GFI GFI 

JGFI 

4 48" 5 

7 

7 

PPB243 

FSD 

48" 

48" 


3 

4 

4 4 4 ETR J 

J 

42" 42" 42" 42" 4 

AP 

11 10 13 12 15 14 6 

18 

J 

1 

5 

EV3 4 

7 42" 

17 

10 11 12 13 14 15 5 6 

J 

SV3B 

J 7 

11 

RHC3 J 

SV3 

7 J 

7 

SEE NOTE 10 SEE NOTE 12 

1 10 13 12 15 14 6 5 

10 

FSD J 3 

SV2 


J 11 RHC2 25 J 

J 

Biology Lab 

11 

RL 

SV3A J 

FD 

B243 

7 


3 

J 

J 

Preparation room 7 

J 16 AP 

1 

2 

SEE NOTE 11 FSD 42" B203 ETR 

8 ETR 2 8 

PPB245 

48" 

12 10 10 

48" 

ETR 

FSD J 6 

12 

9 15 

9 15 

J 

J 7 3 

44" 

42" 42" 42" 42" 

20 16 14 17 21 19 18 22 24 ETR 8 SV2A 

1 1 

J 11 

J 

AP 

12 

11 

RHC1 SV1 

J 

HEV1 J 11 10 10 44" 

11 

16 20 17 14 19 21 22 18 


12 

ETR EV2 

ETR 

J 12 12 

9 11 

20 16 14 17 21 19 18 22 

ETR 

ETR 

G 

RL 

G 


18 

EV1 

11 

11 

9 

ETR 

9 

ETR 

G 

G 

H 

I 

J' 

J 

K 

L 

M 

M' 

N 

O 

O' 

P' 

P 

5 


DOOR CONTROLLER 

ETR 

5 

48" 14 

6 

14 

ETR 

6 

ETR 

ETR 

5 

FD CR 

4 J G 

J 

C 

J 

ETR 

23 

22 ETR 20 

13 

AP 

15 

ETR 

21 18 

J 

21 

6 EV7 

SV7A 

9 

7 9 J SEE NOTE 10 AP 

J HEV2 

ETR 

SEE NOTE 10 5 

J 9 

FSD 

J 24 

4 J 

1 

ETR 


3 10 1 Prep. Room 

12 

PPD231 SV7 

11 D231A 

J 9 J 9 

RHC7 

J FSD 

SEE NOTE 10 ETR 12 

4 

4 

19 

Biology Lab 

D231 

17 

16 

18 


ETR 

5 

17 

20 

19 

16 

21 

J 

FD 

4 

3 

20 

42" 

17 

6 

16 

42" 

15 

19 

18 

42" 

1 

1 

Q 

R 

S 

NEW 4" CONDUIT 

6 

TELECOM ROOM 

B343A 

4. LOCATIONS OF ALL EQUIPMENT AND DEVICES ARE APPROXIMATE. CONTRACTOR TO VERIFY 

ACTUAL SITE CONDITIONS. 

5. RACEWAYS SHALL BE INSTALLED CONCEALED WHERE POSSIBLE. IF EXPOSED RUN IS REQUIRED, 

RACEWAYS SHALL BE PAINTED TO MATCH EXISTING FINISH. COORDINATE WITH CM FOR EXPOSED 

RUNS. 

6. CONNECT NEW DATA OUTLETS TO PATCH PANEL LOCATED IN TELECOM ROOM SBB343A. 

7. FIRE DAMPERS AND FIRE SMOKE DAMPERS FURNISHED AND INSTALLED BY MECHANICAL 

CONTRACTOR. ELECTRICAL CONTRACTOR SHALL PROVIDE POWER CONNECTION. 


U.O.N. 

9. CIRCUIT ROOMS TO PANELBOARDS AS LISTED BELOW: 

PP237: LAB B237 

PP241: LAB B241, PREP ROOM B211 

PP243: LAB B243 

PP245: LAB B245, PREP ROOM B203 

PP231: LAB D231, PREP ROOM D231A 

10. AIR VALVES AND REHEAT COILS ARE PROVIDED BY MECHANICAL CONTRACTOR. 

11. SOLENOID VALVE CONTROLS FURNISHED AND INSTALLED BY PLUMBING CONTRACTOR. 

12. LAB CONTROL PANEL AND TRANSFORMER ARE FURNISHED AND INSTALLED BY MECHANICAL 

CONTRACTOR. ELECTRICAL CONTRACTOR SHALL PROVIDE POWER CONNECTION. COORDINATE 

WITH MECHANICAL CONTRACTOR FOR LOCATIONS. 

13. ELECTRICAL CONTRACTOR SHALL PROVIDE WIRING AND CONDUIT FOR POWER CONNECTIONS TO 

ALL CONTROL DEVICES INSTALLED BY EITHER PLUMBING OR MECHANICAL CONTRACTOR. 

EXISTING IDF RACK 

NEW WALL MOUNTED 

IDF RACK 

NEW CABLE TRAY 

EXISTING CABLE TRAY 

EXISTING 4" CONDUIT 

K 

L 

ENVIRONMENTAL 




t 9732401800 





t 9146867102 

SEALS 







2ND FLOOR AREA B POWER 

AND LOW VOLTAGE PLAN 

2ND FLOOR AREA D POWER 

AND LOW VOLTAGE PLAN 

3RD FLOOR AREA B TELECOM 

ROOM PLAN 



ISSUE BLOCK 

A 

1/8" = 1'0" 

1/8" = 1'0" 

1 2 3 4 5 

1/8" = 1'0" 

E 

A 

C 

D 

KEY PLAN 

B 


PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 




SHEET TITLE 

2ND FLOOR 

POWER & LOW 

VOLTAGE PART 

PLANS 

E130.00 

58 

of 65 

2115419 

JOHN HANNAH 

9/13/2012 12:40:18 PM


DWG. E500.00(091312) 

DETAILS 




1 

2 3 4 5 

D 






CONSULTANTS 

ENVIRONMENTAL 




t 973#240#1800 





t 914#686#7102 

1 

C 

6" X 6" X 4" DEEP SURFACE 

ENCLOSURE WITH SCREW 

COVER TO TERMINATE (3) 1" 

CONDUITS FROM A / V 

FACEPLATE BACKBOX 

STRUCTURAL CEILING 

TO CAMPUS 

NETWORK 

TO DEDICATED 

120VAC, 20A 

A 

SA3032 MASTER CONTROLLER 

UNIT WITH POWER SUPPLY AND 

ENCLOSURE. (1) UNIT CONTROLS 

ALL 5 DOORS. 

(2) SA3000 DOOR CONTROLLER 

BOARDS WITH POWER SUPPLY AND 

ENCLOSURE. (ONE CONTROLLER 

BOARD PER DOOR) 

4" X 4" SURFACE PULLBOX 

WITH SCREW COVER 

STRUCTURAL CEILING 

TELCOM ROOM (B343A) 

2" FLEXIBLE CONDUIT 

DOUBLE GANG FLUSH 

CEILING MOUNTED OUTLET 

BOX 

(3) 1" EMT CONDUITS FROM 

A / V FACEPLATE BACKBOX 

HANGER WIRE RIGIDLY ATTACHED TO 

STRUCTURAL CEILING. WIRE TO MATCH 

CEILING GRID WIRE. (2) WIRES 

REQUIRED PER EACH INSTALLATION 

LOCATION TYPICAL 

HANGER BAR ASSEMBLY 

WITH OUTLET BOX RIGIDLY 

ATTACHED 

A 

REX 

REQUEST#TO#EXIT 

A 

ELECTRIC 

STRIKE 

ELECTRIFIED 

HINGE 

A 

DC 

A 

B 

1" FLEXIBLE 

CONDUIT 

SINGLE GANG FLUSH 

CEILING MOUNTED OUTLET 

BOX 

(SEE NOTES) 

1" EMT CONDUIT TO CORRIDOR 

CABLE TRAY SYSTEM 

HANGER WIRE RIGIDLY ATTACHED TO 

STRUCTURAL CEILING. WIRE TO MATCH 

CEILING GRID WIRE. (2) WIRES 

REQUIRED PER EACH INSTALLATION 

LOCATION TYPICAL 

HANGER BAR ASSEMBLY WITH OUTLET 

BOX RIGIDLY ATTACHED 

SEALS 

CARD 

READER 

LAY#IN CEILING 

ELECTRIFIED 

LOCKSET 

LAY#IN CEILING 

B 

DOUBLE GANG STAINLESS STEEL 

COVERPLATE WITH 2" GROMMETED 

OPENING 

SPACES WITH CEILINGS 

WIRELESS ACCESS POINT 

(PROVIDED BY COLLEGE) 

3 

FLUSH CEILING MOUNTED JUNCTION BOX INSTALLATION DETAIL 

SCALE: NONE 

2 

ACCESS CONTROL SYSTEM 

EQUIPMENT LAYOUT # TYPICAL 

SCALE: NTS 

CABLE SCHEDULE FOR ACCESS CONTROL 

A # 18/2, TWISTED PAIR, SHIELDED, 3/4"C 

B # 18/6. TWISTED PAIR, SHIELDED, 3/4"C 

EACH CABLE GROUP SHALL BE RUN IN SEPARATE CONDUIT 

MAKE ALL FINAL TERMINATIONS PER MANUFACTURER RECOMMENDATIONS 

1 

NOTES: 

WIRELESS ACCESS POINT INSTALLATION DETAIL 

SCALE: NONE 

1. DO NOT INSTALL FACEPLATE ON SINGLE GANG SURFACE/FLUSH OUTLET BOX FOR WIRELESS ACCESS POINT. 

PROVIDE MOUNTING SCREWS AND LABELS. 

2. TERMINATE WIRELESS ACCESS POINT CAT 6 CABLE ON CAT 6 RJ#45 MODULAR PLUG (MALE 8#PIN CONNECTOR) USING 

T568 WIRING CONFIGURATION. PROVIDE 2 FT. OF SLACK CAT 6 CABLE IN THE BOX. 





65#30 Kissena Boulevard 


1 9#13#12 ADDENDUM #1 


ISSUE BLOCK 


PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

2115419 



JOHN HANNAH 


A 

SHEET TITLE 

DETAILS 

1 2 3 4 5 

E#500.00 

59 

of 65 

9/13/2012 12:40:19 PM


DWG. E600.00(091312) 

ELECTRICAL RISER DIAGRAMS 




1 

2 3 4 5 

D 



E001. 

2. FOR PANEL SCHEDULES, SEE DRAWINGS E601 AND E602. 


U.O.N. 






CONSULTANTS 

ENVIRONMENTAL 




BIOLOGY LAB 

ROOM B237 

BIOLOGY LAB 

ROOM B241 

BIOLOGY LAB 

ROOM B243 

BIOLOGY LAB 

ROOM B245 

BIOLOGY LAB 

ROOM D231 

BIOLOGY LAB 

ROOM B237 

BIOLOGY LAB 

ROOM B241 

BIOLOGY LAB 

ROOM B243 

BIOLOGY LAB 

ROOM B245 

BIOLOGY LAB 

ROOM D231 

t 9732401800 

3RD FLOOR 

REMOVE EXISTING 

PANEL AND BRANCH 

CIRCUITS (TYPICAL) 

EXISTING 

PANEL 

AP2N 

EXISTING 

PANEL 

AP2P 

EXISTING 

PANEL 

AP2Q 

EXISTING 

PANEL 

AP2R 

EXISTING 

PANEL 

AP2S 

1 

3RD FLOOR 

REPLACE EXISTNG 

PANEL WITH NEW 

208/120V, 225A 

M.L.O., 3PH, 4W, 42P 

PANEL (TYPICAL) 

NEW 

PANEL 

PPB237 

NEW 

PANEL 

PPB241 

NEW 

PANEL 

PPB243 

NEW 

PANEL 

PPB245 

NEW 

PANEL 

PPD231 





t 9146867102 

2ND FLOOR 

2ND FLOOR 

J 

J 

J 

J 

J 

C 

EXISTING 

DISTRIBUTION 

PANEL TO REMAIN 

120/208V, 3PH, 4W 

(TYPICAL) 

EXISTING 

DISTRIBUTION 

PANEL 

DPH 

800A 

EXISTING 

DISTRIBUTION 

PANEL 

DPI 

800A 

EXISTING 

DISTRIBUTION 

PANEL 

DPJ 

600A 

EXISTING 

DISTRIBUTION 

PANEL 

DPK 

800A 

EXISTING DISTRIBUTION PANEL TO 

REMAIN. 120/208V, 3PH, 4W 

REPLACE EXISTING 

OVERCURRENT DEVICE(S) 

PREVIOUSLY SERVING REMOVED 

PANEL(S) WITH NEW COMPATIBLE 

200A, 3P +N OVERCURRENT 

DEVICE (VERIFY IN FIELD). 

(TYPICAL) 

1 

EXISTING 

DISTRIBUTION 

PANEL 

DPH 

800A 

(ROOM B115A) 

EXISTING 

DISTRIBUTION 

PANEL 

DPI 

800A 

(ROOM B105) 

EXISTING 

DISTRIBUTION 

PANEL 

DPJ 

600A 

(ROOM B101) 

EXISTING 

DISTRIBUTION 

PANEL 

DPK 

800A 

(ROOM D119) 

4#3/0 +1#6G IN EXISTING 2"C 

(TYPICAL) 

1ST FLOOR 

1ST FLOOR 

EXISTING MAIN 

DISTRIBUTION 

SWITCHBOARD 2500A, 

120/208V, 3PH, 4W 

EXISTING MAIN 

DISTRIBUTION 

SWITCHBOARD 2500A, 

120/208V, 3PH, 4W 

SEALS 

CELLAR 

CELLAR 

SWITCHBOARD ROOM 

SWITCHBOARD ROOM 

PART POWER RISER DIAGRAM EXISTING 

NO SCALE 

PART POWER RISER DIAGRAM NEW 


B 


TELECOM ROOM B343A 

NEW WALL 

MOUNT 

IDF 

MOUNT AT 6'0" A.F.F. 

FROM BOTTOM OF RACK 






3RD FLOOR 

CAT6 

PROVIDE NEW 4" CONDUIT FOR 

WIRING OF NEW DEVICES. RUN 

NEXT TO EXISTING 4" CONDUIT. 

A 

2ND FLOOR 

AP 

AP 

BIOLOGY 

LAB B237 

AP 

AP 

BIOLOGY 

LAB B241 

AP 

AP 

BIOLOGY 

LAB B243 

AP 

AP 

BIOLOGY 

LAB B245 

AP 

AP 

BIOLOGY 

LAB D231 

EXISTING 

MDF IN 

ROOM A135E 

BACKBONE CABLING 

24 STRAND, 50 MICRON 

MULTIMODE FIBER OPTIC 

CABLE IN 2" CONDUIT. 




PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 




SHEET TITLE 

2115419 

JOHN HANNAH 

1ST FLOOR 

TELECOMMUNICATIONS RISER DIAGRAM 


1 2 3 4 5 

ELECTRICAL 

RISER 

DIAGRAMS 

E600.00 

60 

of 65 

9/13/2012 12:40:19 PM


DWG. FA001.00 (091312) 

SYMBOL LIST, GENERAL NOTES & RISER 

DIAGRAM 




1 

2 3 4 5 

SCOPE OF WORK 



D 

SYMBOL 

FSD 

R 

CM 

FIRE ALARM SYMBOL LIST 

DESCRIPTION 

WALL MOUNTED STROBE. MOUNT AT 8'0" A.F.F. OR 6" BELOW CEILING, WHICHEVER IS LOWER. 

FIRE SMOKE DAMPER (FURNISHED BY MECHANICAL CONTRACTOR, INSTALLED BY ELECTRICAL CONTRACTOR) 

FIRE ALARM RELAY 

CONTROL MODULE 

FIRE ALARM SYSTEM CONDUIT 

SIZING CHART 

CONDUIT MAX # OF CABLES 

SIZE PER CONDUIT 

3/4" 4 

1" 6 

1 1/4" 8 

1 1/2" 10 

2" 12 

1. PROVIDE A NEW FIRE ALARM SYSTEM FOR THE AREA B AND D LABS. 

2. THE WORK SHALL INCLUDE ALL LABOR, MATERIALS AND NECESSARY SERVICES TO PROVIDE A 

COMPLETE ADDRESSABLE FIRE ALARM SYSTEM. 

3. NEW FIRE ALARM SYSTEM SHALL BE INTERFACED WITH THE MAIN FIRE ALARM CONTROL PANEL 

(FACP) TO PROVIDE THE FOLLOWING FUNCTIONS: 

a. AN ALARM CONDITION INITIATED AT THE MAIN FACP SHALL ALSO ACTIVATE 

AN ALARM CONDITION AT THE AREA “B” AND “D” FACP. 

b. AN ALARM CONDITION INITIATED AT THE AREA “B” AND “D” FACP SHALL 

ALSO ACTIVATE AN ALARM CONDITION AT THE MAIN FACP. 

4. THE SYSTEM SHALL INCLUDE ALL PERIPHERAL DEVICES, MONITORING AND CONTROL MODULES 

AND RELAYS, AND VISUAL NOTIFICATION DEVICES REQUIRED TO PROVIDE A FULLY FUNCTIONING 

SYSTEM. 

1. THE FIRE ALARM CONTRACTOR SHALL RETAIN THE SERVICES OF AN AUTHORIZED 

REPRESENTATIVE OF THE MANUFACTURER OF THE EXISTING FIRE ALARM SYSTEM (SIMPLEX 

GRINNELL PHONE # 2123724209, CONTACT PERSON IS ROBERT LAURIE) TO FURNISH AND 

INSTALL THE INTERFACE CONNECTION AND MAINTAIN THE INTEGRITY OF THE EXISTING FIRE 

ALARM SYSTEM AND WARRANTIES. 

2. EXISTING FIRE ALARM SYSTEM SHALL REMAIN FULLY OPERATIONAL AT ALL TIMES. 

3. COMPONENTS AND DEVICES ASSOCIATED WITH THE NEW FIRE ALARM SYSTEM SHALL BE OFFICE 

OF TECHNICAL CERTIFICATION AND RESEARCH (OTCR) APPROVED AND COMPATIBLE WITH 

EXISTING FACP. 

4. THE FIRE ALARM RISER IN THIS CONTRACT IS FOR DESIGN PURPOSE ONLY. FIRE ALARM 

CONTRACTOR SHALL PROVIDE A COMPLETE FIRE ALARM RISER DIAGRAM, SHOP DRAWING 

SHOWING ACTUAL FIELD WIRING REQUIRED. 

5. PROVIDE FIRESTOPS FOR RACEWAYS PENETRATING WALLS AND CEILINGS TO MAINTAIN ORIGINAL 

FIRE RATING. 





CONSULTANTS 

ENVIRONMENTAL 




TS 

TAMPER SWITCH 

6. INCLUDE ALL WORK FOR INTERCONNECTING CIRCUITRY BETWEEN NEW FIRE ALARM CONTROL 

PANEL AND EXISTING FIRE ALARM CONTROL PANEL. 

t 9732401800 

FS 

WATER FLOW SWITCH 

7. FILE A433 (APPLICATION FOR ELECTRICAL INSPECTION AND SUMMARY OF CONTRACT EQUIPMENT 

TO BE INSTALLED) WITH THE DIVISION OF FIRE PREVENTION OF THE FIRE DEPARTMENT. 



MM 

D 

MONITORING MODULE 

DUCT SMOKE DETECTOR 

8. FILE APPLICATION WITH THE FIRE DEPARTMENT FOR A CERTIFICATE OF APPROVAL ON THE 

ADDITION OF A SUBSYSTEM TO THE EXISTING FACP WHICH HAS FDNY APPROVAL NUMBER. 

9. AS REQUIRED BY THE FIRE DEPARTMENT, ARRANGE FOR INSPECTION OF NEW FIRE ALARM 

SYSTEM. 



t 9146867102 

10. FIRE ALARM WIRING SHALL NOT BE SPLICED. FIRE ALARM WIRING SHALL BE CONTINUOUS FROM 

TERMINAL CABINETS OR FROM EQUIPMENT TO EACH DEVICE. SPLICES ARE NOT PERMITTED 

BETWEEN DEVICES AND/OR CABINETS AT APPROVED JUNCTION AND PULL BOXES. WIRING 

SHOULD BE TERMINATED AT TERMINAL BLOCKS OR DEVICES ONLY. 

C 

11. THE CONTRACTOR IS RESPONSIBLE TO COORDINATE WITH FA VENDOR, MAINTENANCE 

CONTRACTOR AND FDNY TO OBTAIN AND/OR MAINTAIN APPROVED SYSTEM STATUS. 

1 

12. FIRE ALARM CONTRACTOR SHALL VERIFY OPERATION OF EXISTING FIRE ALARM PULL STATIONS 

THROUGHOUT THE BUILDING FOR POSSIBLE REPLACEMENT. 

13. INSTALLATION SHALL BE IN STRICT CONFORMANCE WITH NFPA 72, NATIONAL ELECTRICAL CODE, 

LOCAL CODE(S), AND/OR AUTHORITY HAVING JURISDICTION. 

14. ALL WIRING SHALL BE INSTALLED IN RIGID GALVANIZED CONDUIT. ALL CONDUITS SHALL BE 

CONCEALED AND 3/4" MINIMUM. 

15. COORDINATE MOUNTING LOCATION OF ALL FIRE ALARM DEVICES WITH HVAC EQUIPMENT, 

DUCTWORK, AND PIPING IN THE ROOM. 

TO 120VAC 

SEE ELECTRICAL 

DRAWINGS 

FSD FSD FSD FSD FSD FSD 

FSD FSD FSD 

R 

R 

R 

FSD 

TO 120VAC 

SEE ELECTRICAL 

DRAWINGS 

16. UNLESS OTHERWISE INDICATED, ALL MOUNTING ELEVATIONS ARE CENTERLINE ELEVATIONS. 

17. ARRANGE WIRING FOR NOTIFICATION DEVICES SO THAT LOSS OF PORTION OF THE WIRING TO AN 

AREA WILL NOT RENDER MORE THAN 60% OF THE DEVICES OF EACH TYPE INOPERATIVE. THE 

DEVICES SHALL BE CONNECTED TO THE CIRCUITRY BY MEANS OF ALTERNATE CIRCUITS AS TO 

MAINTAIN AT LEAST PARTIAL AUDIBILITY/VISIBILITY THROUGHOUT THE ENTIRE AREA. 

CM 

D 

D 

D 

D 

CM 

D 

D 

D 

D 

CM 

D 

D 

BUILDING DEPARTMENT NOTES 

SEALS 

2ND FLOOR 

BIOLOGY 

LAB B237 

BIOLOGY 

LAB B241 

BIOLOGY 

LAB B243 

BIOLOGY 

LAB B245 

BIOLOGY 

LAB D231 

120 VAC 

POWER 

SOURCE 

FIRE ALARM 

SHUTDOWN 

CONTACT 

C 

CM 

NC 

FSD 

DAMPER 

ACTUATOR 

FIRE/SMOKE 

DAMPER USED IN 

NORMAL OPERATION 

(TYPICAL) 

1. WORK SHALL BE EXECUTED IN FULL COMPLIANCE WITH THE APPLICABLE PROVISIONS OF ALL 

LAWS, BYLAWS, STATUTES, ORDINANCES, CODES, RULES, REGULATIONS AND LAWFUL ORDERS 

OF PUBLIC AUTHORITIES. THE CONTRACTOR SHALL PROMPTLY NOTIFY THE AUTHORITY'S 

REPRESENTATIVE OF ANY PORTIONS OF THE WORK IN THE CONTRACT DOCUMENTS THAT ARE AT 

VARIANCE WITH THE ABOVE. 

2. COMMENCEMENT OF OPERATIONS: AT LEAST 24 HOURS WRITTEN NOTICE SHALL BE GIVEN TO 

THE COMMISSIONER OF BUILDINGS BEFORE COMMENCING OF WORK. SPECIAL INSPECTION 

ITEMS REQUIRE 72 HOURS PRIOR WRITTEN NOTICE TO PERSONS RESPONSIBLE FOR INSPECTION 

PER SECTION28116.2.3, NEW YORK CITY BUILDING CODE. 

3. ALL MATERIALS, ASSEMBLIES, FORMS METHODS OF CONSTRUCTION AND SERVICE EQUIPMENT 

SHALL MEET THE FOLLOWING REQUIREMENTS: 

A) THEY SHALL HAVE BEEN ACCEPTABLE PRIOR TO THE EFFECTIVE DATE OF THE CODE 

BY THE BOARD OF STANDARDS AND APPEALS AND MEA. 

B 

1ST FLOOR 

TS 

MM 

TS 

MM 

FS 

MM 

NEW FIRE 

ALARM 

CONTROL 

PANEL 

(ROOM D023) 

TIE INTO EXISTING 

FIRE ALARM PANEL 

EXISTING FIRE 

ALARM 

CONTROL 

PANEL 

(ROOM D023) 

TO NEXT FIRE/SMOKE 

DAMPER 

FSD 

DAMPER 

ACTUATOR 

B) THEY SHALL HAVE BEEN ACCEPTED FOR THE USE UNDER THE PRESCRIBED TEST 

METHODS BY THE COMMISSIONER (OR) 

C) APPROVED BY THE BOARD OF STANDARDS AND APPEALS (106.2). 

4. MATERIALS OR ASSEMBLIES REQUIRED TO HAVE A FIRE RESISTANCE RATING SHALL COMPLY 

WITH ONE OF THE FOLLOWING: 

A) THEY SHALL CONFORM WITH A.I.S.G. "FIRE RESISTANCE RATING", DATED 1985 (OR) 

B) THEY SHALL HAVE BEEN TESTED IN ACCORDANCE WITH ASTM E119, STANDARD 

METHODS OF FIRE TESTS OF BUILDING CONSTRUCTION AND MATERIALS AND 

ACCEPTED BY THE COMMISSIONER (OR) 







CELLAR 

C) THEY SHALL HAVE BEEN ACCEPTABLE PRIOR TO THE EFFECTIVE DATE OF THE CODE. 


A 

FIRE ALARM RISER DIAGRAM 


1 

TYPICAL FIRE/SMOKE 

DAMPER (FSD) SHUTDOWN 

1 2 3 4 5 

SCALE: NTS 

SEQUENCE OF OPERATION: 

1. ACTIVATION OF A NEW SPRINKLER WATER FLOW DEVICE OR DUCT SMOKE DETECTOR SHALL: 

A. ACTIVATE THE NEW STROBE LIGHTS IN THE 2ND FLOOR LABS TO FLASH CONTINUOUSLY UNTIL 

MANUALLY RESET OR AUTOMATICALLY STOP AFTER FIVE MINUTES OF ACTIVATION 

B. SHUT DOWN ALL FANS VIA THE EXISTING FACP 

C. RECALL ELEVATORS TO RETURN NONSTOP TO THE MAIN LOBBY VIA THE EXISTING FACP. 

D. CLOSE ALL FIRE SMOKE DAMPERS 

E. ACTIVATE AN ALARM SIGNAL AT THE NEW FACP 

2. ACTIVATION OF A TAMPER SWITCH SHALL: 

A. ACTIVATE A SUPERVISORY SIGNAL AT THE NEW FACP 

3. TROUBLE SIGNAL FROM OPEN CIRCUIT, GROUNDED WIRES, BATTERY FAULT OR WIRE TO WIRE 

FAULT SHALL: 

A. ACTIVATE A TROUBLE SIGNAL AT THE NEW FACP 

4. THE NEW FACP SHALL BE CAPABLE OF ACTIVATING: 

A. AN ALARM SIGNAL AT THE EXISTING FACP 

B. A TROUBLE SIGNAL AT THE EXISTING FACP 

C. A SUPERVISORY SIGNAL AT THE EXISTING FACP 

5. ACTIVATION OF A N ALARM CONDITION IN THE EXISTING FACP SHALL: 

A. ACTIVATE THE STROBE LIGHTS TO FLASH CONTINUOUSLY UNTIL MANUALLY RESET OR 

AUTOMATICALLY STOP AFTER FIVE MINUTES OF ACTIVATION IN THE NEW FACP 

B. CLOSE ALL FIRE SMOKE DAMPER IN THE NEW FACP 




PROJ. MGR: 

DRAWN BY: 

CHECKED BY: 

DESIGN MGR: 

ISSUE BLOCK 




SHEET TITLE 

SYMBOL LIST, 

GENERAL 

NOTES, & RISER 

DIAGRAM 

FA001.00 

63 

of 65 

2115419 

JOHN HANNAH 

9/13/2012 12:40:20 PM


FIRE ALARM SYSTEM PULL STATION CODE CARD 





NAMEPLATE DATA FOR EXISTING DISTRIBUTION 

PANELS 





NAMEPLATE DATA FOR EXISTING PANELBOARD 

UNITS 





CUNY QUEENS COLLEGE – SCIENCE BUILDING 

1 ST FLOOR DIRECTORY 






2 ND FLOOR DIRECTORY 






3 RD FLOOR DIRECTORY

ADDENDUM NO. 1 - STV Group, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?