GV-DSP LPR - Surveillance System, Security Cameras, and CCTV ...

More documents

Recommendations

Info

5Advanced Applications5.3 Restoring to Factory Default SettingsBetween the two models of GV-DSP LPR, the operation of restoring the GV-DSP LPR tooriginal default values can vary and the way the LEDs flash can also be different.To restore to default settings, use the Reset and Default buttons on the front panel of GV-DSP LPR V1, or the Load Default button on the front panel of GV-DSP LPR V2. For thelocation of these buttons see 1.6 Physical Description.Restoring GV-DSP LPR V1 to Default Settings1. Press and then release the Reset button immediately.2. Press and hold the Default button for about 30 seconds, during which all 3 LEDs firstturn on for 5 seconds, Ready and Disk Full/Fault LEDs then turn off, then Ready andDisk Full/Fault LEDs flash once and finally all 3 LEDs turn on again.3. Release the Default button. The process of loading default values is complete, and theGV-DSP LPR V1 starts rebooting itself with the 3 LEDs turning off.4. Wait until the Power and Ready LEDs turn on again. After this all the settings arereturned to default values.Restoring GV-DSP LPR V2 to Default Settings1. Unplug and plug the power cable to start.2. Press and hold the Load Default button until the Ready LED blinks. This may take upto 60 seconds. The Ready LED will blink twice.3. Release the Load Default button. The process of loading default values is complete,and the GV-DSP LPR V2 starts rebooting itself.4. Wait until the Ready LED turns on again. After this all the settings are returned todefault values.Note: Before the Ready LED is on again, do not unplug the power cable; otherwise theloading of default values will fail.47
Chapter 6 The I/O Terminal Block6.1 GV-DSP LPR V1The 16-pin terminal block, located on the rear panel, provides the interface to: four digitalinputs, four relay outputs, an RS-232 interface, a Wiegand interface and auxiliary power.The I/O terminal block can be used to develop applications for motion detection, eventalerts, access control and a variety of other functions.Note: RS-232 and Wiegand interfaces are NOT functional now.Pin AssignmentFigure 6-1The pin assignment for the terminal block is described in the table below.Pin Function Pin Function1 Relay Output 1 9 DC 5V Out for GV-Relay Module2 Digital Input 1 10 Ground3 Relay Output 2 11 RS-232 (TX)4 Digital Input 2 12 Wiegand D05 Relay Output 3 13 RS-232 (RX)6 Digital Input 3 14 Wiegand D17 Relay Output 4 15 Ground8 Digital Input 4 16 DC 12V Out for Wiegand Card Reader48
Page 1 and 2: GV-DSP LPRUser's ManualBefore attem
Page 3: PrefaceWelcome to the GV-DSP LPR Us
Page 6 and 7: Recognition Engine VersionRecogniti
Page 8 and 9: 1Introduction1.2 Packing List1. AC
Page 10 and 11: 1Introduction1.4.1.2 GV-DSP LPR V21
Page 12 and 13: 1Introduction1.4.2.2 GV-DSP LPR V2F
Page 14 and 15: 2Getting Started1. Open your web br
Page 16 and 17: 3Accessing the GV-DSP LPRChapter 3
Page 18 and 19: 3Accessing the GV-DSP LPR3.2.1 The
Page 20 and 21: 3Accessing the GV-DSP LPR3.2.3 Snap
Page 22 and 23: 4Administrator ModeChapter 4 Admini
Page 24 and 25: 4Administrator Mode[Engine Setting]
Page 26 and 27: 4Administrator Mode• I/O: Activat
Page 28 and 29: 4Administrator ModePOS Overlay Plat
Page 30 and 31: 4Administrator Mode• Maximum numb
Page 32 and 33: 4Administrator Mode4.2 I/O ControlT
Page 34 and 35: 4Administrator Mode4.3 Events & Ale
Page 36 and 37: 4Administrator Mode[Configure conne
Page 38 and 39: 4Administrator ModeTo enable the DD
Page 40 and 41: 4Administrator Mode4.5 ManagementTh
Page 42 and 43: 4Administrator Mode4.5.2 Storage Se
Page 44 and 45: 4Administrator Mode4.5.4 Log Inform
Page 46 and 47: 5Advanced ApplicationsChapter 5 Adv
Page 48 and 49: 5Advanced Applications2. Double-cli
Page 50 and 51: 5Advanced Applications5.2 Backing U
Page 54 and 55: 6The I/O Terminal BlockRelay Output
Page 56 and 57: 6The I/O Terminal BlockRelay Output
Page 58 and 59: SpecificationsSpecificationsModel G

GV-DSP LPR - Surveillance System, Security Cameras, and CCTV ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?