Manual - Building Block Video CCTV

NEUTRALSW1 Lens VoltageON = 6V, OFF = 12VSW8(on/off) Start Self Test - LEFT,RIGHT,UP,DOWN,AUX.,ZOOM IN,OUT, FOCUS NEAR,FAR, IRIS OPEN,CLOSESW2 Iris OverrideON = 2.5 - 5.5V, OFF = 2.5 - 12VSW3/SW4 Aux selectionFunction SW3 SW4WASH ON ONLIGHTS ON OFFWIPE OFF ONAUTOPAN OFF OFFSW5 ON Overides Random PanSW6 NOT USEDSW7 ON Overides Remote Self TestSW8 ON = SELF TESTSTATUS LEDSCABLEEven Flashing -Telemetry and syncok.Mainly ON - No TelemetryMainly OFF - No sync from cameraERRORON - Telemetry error.ON20mAtwisted pairtelemetry ifrequired.CABLEGROUNDIRIS OVERRIDEAUTO IRISIRIS OVERRIDEBuilding Block Video Ltd31 2 3 4 5 6 7 8FOCUSERRORCOMMON17 Apex Park, Diplocks Industrial Estate, Hailsham, East Sussex, UK. BN27 3JU. Tel: +44 (0)1323 842727 Fax: +44 (0)1323 842728Tech Support: +44 (0)1323 444600 Web site for manuals/data sheets/application notes etc. www.bbvcctv.comZOOMRY5 RY4 RY3 RY2 RY11 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 1 0EARTHLIVEAUXILIARYOUTPUTNEURALEARTHLEFTRIGHTUPDOWN11PAN/TILT HEAD12NEUTRALEARTHCable compensation.Lift:Clockwise to increaseHF content.Gain:Clockwise to increaseoverall video level.Gain and Lift are factory preset for250M of RG59 cable.J5LIVEUNSWITCHEDOUTPUT.CAMERASUPPLY ETCF2 Output fuse ratingSupply Output Fuse230 230 5A T230 24 315mA T110 110 5A T110 24 630mA T24 24 5A TVideo InFrom CameraVideo OutTo Transmitter250M-RG59500M-CT125110Vac and24Vac supplyoptions areavailable.This must bespecified atorder time.230Vac asstandard.BBV 24VAC option plugs intothis socket for 24Vac output.ALL J6 outputs are at supply levelor 24Vac when 24V option fitted.Rx300 Mark II ConnectionsSELF-TEST AND DIAGNOSTIC SEQUENCESThe diagnostic system and status check, which will activate each camera function for two seconds in turn, isactivated either locally by pressing a switch on the PCB or remotely from a BBV keypad. When testing thesystem locally, before initiating the diagnostic system and status check by turning SW8 ON momentarily,ensure that the Cable LED is on (i.e. either flashing or continuously). If not, this indicates that either thepower is not attached to the PCB, or there has been a major PCB error. Rectify accordingly.The Error LED flashes at a two-second rate during self-test. If the Cable LED fails to extinguish, then theunit is unable to self-tune and should be returned for repair.Order of function test:Camera Moves LeftCamera Moves RightCamera Moves UpCamera Moves DownAuxiliary FunctionLens Zoom-InLens Zoom-OutLens Focus NearLens Focus FarAuto Iris OpenAuto Iris CloseDiagnostic Check Complete, unitresets and continues normaloperation.Telemetry Receiver Installation HandbookRx300mk22 July 2004 Rev6Page_11