Manual - Building Block Video CCTV

More documents

Recommendations

Info

SW8(on/off) Start Self Test - LEFT,RIGHT,UP,DOWN,AUTOPAN,LAMPS,WIPE,WASH,ZOOM IN,OUT, FOCUS NEAR,FAR, IRIS OPEN,CLOSEONZOOMFOCUSGROUNDIRIS OVERRIDE20mAtwisted pairtelemetry ifrequired.1 2 3 4 5 6 7 81 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 1 0AUTO IRISIRIS OVERRIDEMotorisedIrisBuilding Block Video Ltd17 Apex Park Hailsham, East Sussex, UK. BN27 3JF. Tel: +44 (0)1323 842727 Fax: +44 (0)1323 842728Tech Support: +44 (0)1323 444600 Web site for manuals/data sheets/application notes etc. www.bbvcctv.com111213141516171819LIVEEARTHNEUTRALLIVELEFTRIGHTUPDOWNAUTOPANEARTHNEUTRALEARTHNEUTRALLIVEEARTHNEUTRALLIVEEARTHNEUTRALWASHERWIPERLAMPSSTATUS LEDSCABLEEven Flashing -Telemetryand sync ok.PAN/TILT HEADUNSWITCHEDOUTPUT.CAMERASUPPLYETC.Video InFrom CameraCABLEERRORJ10 - PRESETFOCUSTILT+5V 0VZOOM1 2 3 4+5V 0VFOCUS ZOOM IRISPAN5 6 7 81 2 3 4 5 6 7 86V0%LENS9VINCH50%12V100%SW1 Iris OverrideON = 2.5-5.5V, OFF = 2.5-12VLens Directions OFF = reverseSW2 Reverse Zoom directionSW3 Reverse Focus directionSW4 Reverse Iris directionSW5 ON=No Self TestSW6 ON=No Lens PresetSW7 ON=Datum Mode(No Patrol)SW8 ON=Start Self TestLENS Lens voltage. 6 - 12VINCH Inch Speed 0-100%Mainly ON - No TelemetryMainly OFF- No sync fromcameraERRORON - Telemetry error.Cable compensation.Lift:Clockwise to increaseHF content.Gain:Clockwise to increaseoverall video level.Gain and Lift are factory preset for250M of RG59 cable.Video OutTo Transmitter250M-RG59500M-CT125110Vac and24Vac supplyoptions areavailable.This must bespecified atorder time.230Vac asstandard.Output fuse ratingSupply Output Fuse230 230 5A T230 24 315mA T110 110 5A T110 24 630mA T24 24 5A TBBV 24VAC mk.2 option plugsinto this socket for 24Vac output.ALL J6 outputs are at mains or24Vac when 24V option fitted.Including unswitched outputs.Rx400P Mark II Issue 5 ConnectionsLIFTGAINOUTPUT FUSE93004iss.5IRISCOMMONTelemetry Receiver Installation HandbookRx400P mk22 July 2004 Rev6Page_20
Rx400DC24Vdc high/variable Pan/Tilt Zoom/Focus/Iris/3 Aux 16 presets8 local alarms 12Vdc 500mA supply.TABLE OF CONTENTS1. Pre-installation Checks and Safety Procedures 22Unpacking 22Important safety precautions 222. Introduction 23General 23Technical specification 23, 24Programmable output features 23Cable connection method 25Fig. 1 Wago cable connectorsCable types 253. Installation 26Operating voltage 26Cable connection instructions 27Fig. 2 Cable connection diagram4. Setup 28Diagnostic aids 28Cable length compensation 29Fig. 3 Launch amplifierSelf-test 29Fig. 4 Self test sequenceProgramming the unit 30, 31Settings for normal operation 32Patrol Mode and Datum operation 32Pre-sets 33Telemetry Receiver Installation HandbookRx400DC2 July 2004 Rev6Page_21
Page 3 and 4: Rx200 mk2AC Left/Right/Wipe/Lights/
Page 5 and 6: Rx200 INSTALLATION INSTRUCTIONSThe
Page 7: LAUNCH AMPLIFIERThere are two varia
Page 12 and 13: LAUNCH AMPLIFIERThere are two varia
Page 15: 0222586GCo-Ax Cable (Minimum Specif
Page 18 and 19: CABLE CONNECTIONS FOR Rx400P UNITSC
Page 22 and 23: 1. PRE-INSTALLATION CHECKS AND SAFE
Page 24 and 25: Auto-Iris Output:Video Input:Video
Page 26 and 27: 3. INSTALLATIONOPERATING VOLTAGEThe
Page 28 and 29: 4. SETUPDIAGNOSTIC AIDSTwo L.E.D.
Page 30 and 31: PROGRAMMING THE UNITProgramming is
Page 32 and 33: SETTINGS FOR NORMAL OPERATIONSevera
Page 34 and 35: INSTALLATION INSTRUCTIONS FOR PCB-B
Page 36 and 37: BBV TX1500 exampleBuilding Block Vi
Page 38 and 39: - This page is blank for your notes
Page 40: The BBV product range.Product Descr

Manual - Building Block Video CCTV

Create successful ePaper yourself

Delete template?

Save as template?