2002 Replacement Parts Catalog - cedip

Drill Pipe Shearing RequirementsThe minimum shearing configurations needed for each size U BOP to meet the requirements ofthe second edition of API 16A are listed in the following chart. Each shearing configuration iscapable of shearing the corresponding pipe at a closing pressure equal to or less than 2800 psi.For further information on shearing requirements for different pipe sizes and grades, contactyour Cameron representative.API Designated Size Ram Type Pressure Rating (psi) Pipe OD (In.) Pipe lb/ft Pipe Grade Shearing Configuration7-1/16” SBR All 3-1/2 13.3 S Shear Bonnets with Tandem Boosters11” SBR 10,000 and Lower 5 19.5 E Shear Bonnets with Tandem Boosters11” DS/ISR 10,000 and Lower 5 19.5 E Large Bore Shear Bonnets11” SBR 15,000 and Higher 5 19.5 G Large Bore Shear Bonnets with Tandem Boosters13-5/8” SBR 10,000 and Lower 5 19.5 G Shear Bonnets with Tandem Boosters13-5/8” DS/ISR 10,000 and Lower 5 19.5 G Large Bore Shear Bonnets13-5/8” SBR 15,000 and Higher 5 19.5 S Large Bore Shear Bonnets16-3/4” SBR All 5 19.5 S Large Bore Shear Bonnets18-3/4” SBR All 5 19.5 S Standard Bonnets20-3/4” SBR 3000 and Lower 5 19.5 G Shear Bonnets with Tandem Boosters21-1/4” SBR 3000 and Lower 5 19.5 G Shear Bonnets with Tandem Boosters21-1/4” SBR 5000 and Higher 5 19.5 S Standard Bonnets21-1/4 SBR 10,000 and Higher 5 19.5 G Standard BonnetsLarge Bore Shear Bonnets12A**3A42A5A26A24A2ALarge Bore Shear RamBonnet AssemblySD-017503ItemNo.**2ADescription(2 Required perCavity)Bonnet Assembly(Right)Bonnet Assembly(Left)IntermediateFlange/Shear11”3000 psi Model II11”5000 psiModel II11”10,000 psiModel II11”15,000 psiModel 7913-5/8”3000 psiModel 1113-5/8”5000 psiModel II13-5/8”10,000 psiModel II13-5/8”15,000 psiModel B16-3/4”5000 psiModel B16-3/4”10,000 psiModel II20-3/4”3000 psiModel II21-1/4”2000 psiModel II615195-01 615194-01-00-01 614596-01-00-01 615419-01 615196-01 615191-01-00-01 614498-01-00-02 615540-01 615530-01 615537-01 615526-01 615525-01615195-02 615194-02-00-01 614596-02-00-01 615419-02 615196-02 615191-01-00-01 614498-02 615540-02 615530-02 615537-02 615526-02 615525-02615188-01 615188-01 615188-01 615459-01 615192-01 615192-01-00-01 614766-01-00-02 615538-01 615528-01 615535-01 615523-01 615523-013A Bonnet/Shear 615189-03 615189-02 615189-01 615640-01 615143-02 615143-01 614772-01 615448-01 615527-01 615534-01 615522-01 615522-025A24A26A42AOperatingPiston/ShearO-Ring, Int Flg toBonnet LipLip Seal,OperatingPiston/ShearWear Ring,OperatingPiston/Shear615190-02-00-01 615190-02-00-01 615190-02-00-01 615457-01 615209-01 615209-01-00-01 614760-01-00-02 615539-01 615529-01 615536-01 615524-01 615524-01702645-45-51 702645-45-51 702645-45-51 702645-45-81 702645-45-81 702645-45-81 702645-45-81 702645-46-51 702645-46-51 702645-46-51 702645-45-81 702645-45-81710586 710586 710586 710542 710542 710542 710542 710588 710588 710588 710542 710542049223-15 049223-15 049223-15 049223-04 049223-04 049223-04 049223-04 049223-17 049223-17 049223-17 049223-14 049223-14**Two shear bonnet assemblies, one right and one left, are required per cavity. The shear bonnet assembly consists of all items shown on the illustration.**See pages 17, 19 and 21 for bonnet bolt part numbers.TC1001 24 © 2002 Cooper Cameron, Cameron Division