REGISTER OVERVIEW PLASTICS

More documents

Recommendations

Info

KETRON ® PEEK Properties of Ketron ® Peek (polyetheretherketone) Material density: 1.31 g/cm 3 Service temperature: +250/310 °C (20.000 hours/temporary) Temporary = only a few hours, where no or only low loads may occur This semi-crystalline high-performance plastic provides a unique combination of very good mechanical properties, high temperature resistance and excellent chemical resistance. Main properties of Ketron ® PEEK: • Upper service temperature limit in air, continuous 250 °C, temporary peaks up to 310 °C • High mechanical strength, rigidity and creep strength over a wide temperature range • Excellent chemical and hydrolysis resistance • Excellent wear resistance and good sliding properties (particularly Ketron ® PEEK HPV and PEEK CA 30) • Very high dimensional stability • Outstanding UV resistance • Excellent resistance to high-energy radiation (gamma and X rays) • Inherent non-flammability and very low smoke emissions in the event of a fire • Good electrical and dielectric behaviour (only Ketron ® PEEK, not Ketron ® PEEK HPV/PEEK CA 30) Comment: Above 150 °C, the mechanical properties of all Ketron ® PEEK types diminish significantly and the linear coefficient of thermal expansion rises considerably. As a result, Duratron ® PAI could be better suited to precision parts at high temperatures over 150 °C. Also, page through online! www.reiff-tp.com Grades: Telephone hotline: +49 1803 00 26 22 40 / Fax hotline: +49 1803 00 26 22 41 9 cents/60 sec. from the German fixed network <strong>PLASTICS</strong> 13/75 Ketron ® PEEK 1000 colour natural (brownish grey/black) Offers the best toughness and impact strength of all Ketron ® PEEK grades with excellent chemical resistance. Ketron ® PEEK HPV colour black The addition of carbon fibres, graphite and PTFE give a "bushing type" with a low coefficient of sliding friction, high wear resistance and a high PV limit value. Ketron ® PEEK GF 30 colour brownish grey This type, which is reinforced with 30 % glass fibre, has better rigidity, mechanical strength and creep strength than Ketron ® PEEK 1000. Ketron ® PEEK CA 30 colour black This type, which is reinforced with 30 % carbon fibre, combines even better rigidity and creep strength than Ketron ® PEEK GF 30 with optimum wear resistance. Ketron ® PEEK TX (PEEK + solid lubricant) This new member of the Ketron ® PEEK group of products has been specially developed for the food industry. Just like the existing Ketron ® PEEK 1000, this new self-lubricating material also has a composition that is suitable for contact with foodstuffs, but it also offers much better wear and sliding behaviour. As a result, Ketron ® PEEK TX is especially well suited for sliding and wearing elements in the temperature range 100 °C to 200 °C. Application: Ketron ® PEEK 1000 = medical engineering, pharmaceutical and food processing industries Ketron ® PEEK HPV = applications for parts subject to high wear and friction stresses Ketron ® PEEK GF 30 = applications for parts with high dimensional stability Ketron ® PEEK CA 30 = wearing parts with close tolerances, as well as very good rigidity and creep strength Processing: Machining, see machining information Dimensions: Available dimensions on request
13/76 <strong>PLASTICS</strong> Symalit ® 1000 PVDF Properties of Symalit ® 1000 PVDF (polyvinylidene fluoride) Material density: 1.79 g/cm 3 Service temperature: –30 to +150/160 °C (20.000 hours/temporary) Temporary = only a few hours, where no or only low loads may occur This fluoropolymer has excellent mechanical properties, paired with outstanding chemical resistance. Chemically speaking, Symalit ® 1000 PVDF falls between PE HD and PTFE: it is easy to machine like PE HD, but with its high chemical resistance at increased temperatures is more like PTFE. Main properties of Symalit ® 1000 PVDF: • High upper continuous service temperature limit in air 150 °C • Good mechanical strength, rigidity and creep strength over a wide temperature range • Excellent chemical and hydrolysis resistance • Good sliding properties and wear resistance • Outstanding UV and weather resistance • Good electrical insulating properties • Physiologically safe (suitable for contact with foodstuffs) • Inherent non-flammability Also, page through online! www.reiff-tp.com Technical information: In Chapter 14 "Technical Knowledge" starting on page 93 we inform you in detail. Comment: Symalit ® 1000 PVDF is a thermoplastic structural material with the properties that are typical of thermoplastics, such as the ability to be extruded, welded and hot formed. Grade: Symalit ® 1000 PVDF colour natural (white) This is a fluoropolymer that combines good mechanical, thermal and electrical properties with excellent chemical resistance. The raw material also complies with the guidelines of the European Union and the regulations of the American FDA as regards compatibility with foodstuffs. Application: Symalit ® 1000 PVDF A versatile structural material that is used primarily in the petrochemical, chemical, metallurgical, pharmaceutical, food, paper, textile and nuclear industries. Processing: Can be machined, hot formed and welded – see machining information Dimensions: Available dimensions on request plastics@reiff-group.com / www.reiff-tp.com
Page 1 and 2:
13/6 PLASTICS REGISTER OVERVIEW PLA
Page 3 and 4:
13/8 PLASTICS SELECTION GUIDE FOR S
Page 5 and 6:
13/10 PLASTICS ABS ABS copolymers I
Page 7 and 8:
13/12 PLASTICS uPVC (UNPLASTICISED
Page 9 and 10:
13/14 PLASTICS UPVC BOARDS Extruded
Page 11 and 12:
13/16 PLASTICS UPVC TUBES Extruded
Page 13 and 14:
13/18 PLASTICS PPVC Boards/Films It
Page 15 and 16:
13/20 PLASTICS PE HD Material chara
Page 17 and 18:
13/22 PLASTICS PE ROUND RODS Extrud
Page 19 and 20: 13/24 PLASTICS PP BOARDS Extruded I
Page 21 and 22: 13/26 PLASTICS TECHNICAL SEMI-FINIS
Page 23 and 24: 13/28 PLASTICS TECHNICAL SEMI-FINIS
Page 25 and 26: 13/30 PLASTICS PHYSICAL PROPERTIES
Page 27 and 28: 13/32 PLASTICS PA 6 BOARDS Extruded
Page 29 and 30: 13/34 PLASTICS PA 6 ROUND RODS Extr
Page 31 and 32: 13/36 PLASTICS PA 6.6 ROUND RODS Ex
Page 33 and 34: 13/38 PLASTICS POM/PET Product desc
Page 39 and 40: 13/44 PLASTICS POM C ROUND RODS Ext
Page 41 and 42: 13/46 PLASTICS PET ROUND RODS Extru
Page 43 and 44: 13/48 PLASTICS PE HD UHMW Product d
Page 45 and 46: 13/50 PLASTICS PE 1000 BOARDS Press
Page 47 and 48: 13/52 PLASTICS PMMA ACRYLIC GLASS P
Page 49 and 50: 13/54 PLASTICS PC MAKROLON ® Techn
Page 51 and 52: 13/56 PLASTICS PC MAKROLON ® Board
Page 53 and 54: 13/58 PLASTICS PET Properties of PE
Page 55 and 56: 13/60 PLASTICS PETG Properties of P
Page 57 and 58: 13/62 PLASTICS uPVC GLASS pPVC TRAN
Page 59 and 60: 13/64 PLASTICS PPVC Boards/Films It
Page 61 and 62: 13/66 PLASTICS HIGH-PERFORMANCE PLA
Page 63 and 64: 13/68 PLASTICS LIFE SCIENCE GRADES
Page 65 and 66: 13/70 PLASTICS DURATRON ® PI Prope
Page 69: 13/74 PLASTICS Quadrant ® PPSU Qua
Page 73 and 74: 13/78 PLASTICS PEEK 1000 BOARDS Ket
Page 75 and 76: 13/80 PLASTICS TECHTRON ® PPS DURA
Page 77 and 78: 13/82 PLASTICS PVDF 1000 BOARDS PVD
Page 81 and 82: 13/86 PLASTICS PTFE ROUND RODS Virg
Page 83 and 84: 13/88 PLASTICS CONDUCTIVE PLASTICS
Page 85 and 86: 13/90 PLASTICS CONDUCTIVE PLASTICS
Page 87 and 88: 13/92 PLASTICS BOARDS FOR THE ADVER
Page 89 and 90: 13/94 PLASTICS LF (LAMINATED FABRIC
Page 91 and 92: 13/96 PLASTICS LF PANELS Type 2082
Page 93 and 94: 13/98 PLASTICS LP (LAMINATED PAPER)
Page 95 and 96: 13/100 PLASTICS LP BOARDS Type 2061
Page 97 and 98: 13/102 PLASTICS PUR (POLYURETHANE)
Page 99 and 100: 13/104 PLASTICS PUR BOARDS Polyuret
Page 101 and 102: 13/106 PLASTICS INFORMATION ABOUT M
Page 103 and 104: 13/108 PLASTICS INFORMATION ABOUT M
show all

REGISTER OVERVIEW PLASTICS

Create successful ePaper yourself

Delete template?

Save as template?