REGISTER OVERVIEW PLASTICS

uPVC
pPVC
Material characteristics for uPVC (unplasticised polyvinyl chloride)
pPVC (plasticised polyvinyl chloride)
Material density: 1.22 g/cm 3
Service temperature: –35 °C standard resistance to cold,
up to +60 °C
pPVC boards, transparent, particularly for use as replacement
swing-door leaves, rolling or folding gates, or strip doors.
Board strips for vertical blinds with round extruded edges.
• For sound and heat insulation
• Fire behaviour according to DIN 53 382, i.e. does not continue
to burn or smoulder
• High cold crack resistance
• Transparency > 80 %
• Stabilised against ageing and UV
• High wear resistance
Filter and light-protection material also characterised by:
• Reliable absorption of damaging rays
• Protection against flying sparks
• Non-flammable
• DIN tested safety (GS) UV 4 or 7
Comment:
Special grades – particularly for cold-store areas,
with excellent flexibility even at negative temperatures:
–45 °C extremely resistant to cold, up to +60 °C (on request)
Telephone hotline: +49 1803 00 26 22 40 / Fax hotline: +49 1803 00 26 22 41 9 cents/60 sec. from the German fixed network
PLASTICS 13/13
Name according to DIN ISO 1043 uPVC uPVC
Increased impact resistance
Material name Norm Unit PVC CAW PVC MZ
Density DIN 54379 g/cm 3 1.42 1.42
Flexural modulus of elasticity DIN 53457 N/mm 2 3000 2800
Yield stress DIN 53455 N/mm 2 58 52
Elongation at tear DIN 53455 % 15 20
Impact strength DIN 53453 kJ/m 2 NB NB
Notch toughness DIN 53453 kJ/m 2 4 10
Ball indentation hardness H 358/30 DIN 53456 N/mm 2 130 110
Shore hardness D DIN 53505 – 82 77
Vicat softening temperature B/50 DIN 53460 K (°C) 351 (78) 348 (75)
Av. linear coefficient of thermal expansion DIN 53752 K–1 0.8 ·10 –4 1.0 ·10 –4
Thermal conductivity* DIN 52612 W/mK 0.159 0.159
Dielectric strength** method K20/P50 DIN 53481 kV/mm 39 34
Volume resistivity, annular electrode DIN 53482 Ohm · cm > 10 15 > 10 15
Surface resistivity, electrode A DIN 53482 Ohm 10 15 10 14
Tracking resistance method KC DIN 53480 V > 600 > 600
Permittivity
at 300 – 1000 Hz DIN 53483 – 3.2 3.3
at 3 · 105 Hz DIN 53483 – 3.0 3.1
Dielectric power factor
at 300 Hz DIN 53483 – 0.03 0.03
at 1000 Hz DIN 53483 – 0.02 0.02
at 3 · 10 5 Hz DIN 53483 – 0.02 0.03
** Measured on test specimens 10 mm thick
** Measured on test specimens 1 mm thick
The data given is a guide and may vary according to the processing
method used and the way in which the test specimen was produced.
If there is no indication to the contrary, these are average
values of measurements taken on extruded boards 4 mm thick.
The data cannot be transferred to finished products as is.
The processor and/or user must check that our materials are suitable
for the specific purpose in question.
Moulding material name (DIN 7748, version of 9/85)
PVC CAW: FM DIN 7748-PVC-U, ED, 078-04-33
PVC MZ: FM DIN 7748-PVC-U, EDLP, 076-08-28
Grades:
pPVC boards natural, transparent
Fabric-reinforced boards, as well as filter and light-protection
strips including fastening material and installation available on
request
Application:
Transparent grade, e.g. for flexible door leaves of any type.
Filter protection with sun protection factor (strip goods)
Tech. grade, colour natural, e.g. for machine bases, as impact
protection for linings, as well as seals and punched parts
Processing:
Can be cut/punched/stuck to one another using solvent adhesives
Dimensions:
Board thickness 2 - 3 - 4 - 5 - 7 - 10 mm – 1000 mm standard width
Special widths up to 2200 mm possible (on request)
Roll lengths of 20 m/or blanks
pPVC board strips, transparent, with round extruded edges
200 x 2 mm/300 x 3 mm/400 x 4 mm/roll length of 50 m or blanks