- Page 1 and 2: Unisys Title o New Release • Revi
- Page 3 and 4: DCP SERIES Maintenance Software Tes
- Page 5 and 6: DCP SERIES Maintenance Software Tes
- Page 7 and 8: DCP Series Maintenance Software Tes
- Page 9 and 10: Contents About This Guide .........
- Page 11 and 12: Contents Enable/Disable Data Checki
- Page 13: Figures 1-1. Six Tasks of Using TL3
- Page 17 and 18: About This Guide Purpose Audience T
- Page 19 and 20: Appendix B. Error Messages and Faul
- Page 21 and 22: About This Guide DCP/5 Installation
- Page 23 and 24: Section 1 Introduction This section
- Page 25 and 26: Testing Line Modules and Exiting TL
- Page 27 and 28: Downing Lines Assigned to Telcon To
- Page 29 and 30: Figure 1-2. Main Menu Introduction
- Page 31 and 32: Using the DCP/OS Console Function K
- Page 33 and 34: Interactive Mode Figure 1-4. TL3 Me
- Page 35 and 36: Section 2 Configuring Ports This se
- Page 37 and 38: Configuring Ports 3. The Port Param
- Page 39 and 40: Table 2-1. Parameter Definitions (c
- Page 41 and 42: The fields on the status screen (se
- Page 43 and 44: UDLC Secondary Chain Configuring Po
- Page 45 and 46: Async Primary Chain This option sen
- Page 47 and 48: EBCDIC Bisync Primary Chain Configu
- Page 49 and 50: 1100 FDX Primary Chain Configuring
- Page 51 and 52: 4X1 Async Primary Chain Configuring
- Page 53 and 54: Multiple Device Line Module Partial
- Page 55 and 56: 16-Bit Parallel Back-to-Back Chain
- Page 57 and 58: Host-Block Mux Chain Configuring Po
- Page 59 and 60: ILM-40 Ethernet Chain Configuring P
- Page 61 and 62: ILM-60 4X High Speed Chain Configur
- Page 63 and 64: Table 2-43. Line Modules and Hardwa
- Page 65 and 66:
Section 3 Specifying Port Controls
- Page 67 and 68:
Section 4 Display Status Informatio
- Page 69 and 70:
View Port Status Display Status Inf
- Page 71 and 72:
Display Test Statistics Display Sta
- Page 73 and 74:
Section 5 Specifying Test Condition
- Page 75 and 76:
Configure Files Specifying Test Con
- Page 77 and 78:
Section 6 Miscellaneous Options Run
- Page 79 and 80:
Section 7 Mass Storage Subsystem Te
- Page 81 and 82:
Appendix A Acronyms and Abbreviatio
- Page 83 and 84:
STX Start of text Sync LM Synchrono
- Page 85 and 86:
Appendix B Error Messages and Fault
- Page 87 and 88:
Error Messages and Fault Isolation
- Page 89 and 90:
Error Messages and Fault Isolation
- Page 91 and 92:
Not Enabled After 15 State Items Er
- Page 93 and 94:
UDLC Primary and Secondary Chains U
- Page 95 and 96:
Error Messages and Fault Isolation
- Page 97 and 98:
Error Messages and Fault Isolation
- Page 99 and 100:
Bit 24 Set if carrier went off duri
- Page 101 and 102:
Error Messages and Fault Isolation
- Page 103 and 104:
BSC Input Status Error Messages and
- Page 105 and 106:
Error Messages and Fault Isolation
- Page 107 and 108:
Error Messages and Fault Isolation
- Page 109 and 110:
Error Messages and Fault Isolation
- Page 111 and 112:
Error Messages and Fault Isolation
- Page 113 and 114:
Error Messages and Fault Isolation
- Page 115 and 116:
Error Messages and Fault Isolation
- Page 117 and 118:
Error Messages and Fault Isolation
- Page 119 and 120:
Error Messages and Fault Isolation
- Page 121 and 122:
4X1 Async and Video Text Chain Mult
- Page 123 and 124:
Asynchronous Input Status Error Mes
- Page 125 and 126:
Error Messages and Fault Isolation
- Page 127 and 128:
Error Messages and Fault Isolation
- Page 129 and 130:
Error Messages and Fault Isolation
- Page 131 and 132:
FEPI and PLM FEPI FEPI Output Statu
- Page 133 and 134:
Error Messages and Fault Isolation
- Page 135 and 136:
Error Messages and Fault Isolation
- Page 137 and 138:
HSILM20 Input Status Error Messages
- Page 139 and 140:
ILM Status Error Messages and Fault
- Page 141 and 142:
Input Data Transfer Status Error Me
- Page 143 and 144:
Error Messages and Fault Isolation
- Page 145 and 146:
Appendix C Line Module Identifiers
- Page 147 and 148:
HID (Hex) Line Module Short Name Ta
- Page 149 and 150:
Appendix D Installing DCP Maintenan
- Page 151 and 152:
Preparing the Hard Disk for a Local
- Page 153 and 154:
Step Action 7 Press the XMIT key. T
- Page 155 and 156:
Preparing the Hard Disk Step Action
- Page 157 and 158:
Loading the Maintenance Software on
- Page 159 and 160:
Step Action 8 Enter the following c
- Page 161 and 162:
DCP600 Procedures Preparing the DCP
- Page 163 and 164:
Loading the Maintenance Software on
- Page 166:
*74318080-202* 74318080-202