metric Oscillator - Beckman Institute Laser Resource Center

More documents

Recommendations

Info

<strong>Center</strong> the first IHS-355 on the pump beam. Adjust this IHS-355 tocenter the pump beam on the second IHS-355. Adjust this second dichroic so thatthe pump beam passes unobstructed through the center of the input port of theMOPO-700 and the alignment port situated in line with the input port. Please referto figure 3-7 to identify various MOPO-700 components.DesignatorsUVTMBSPHPLN LPHROCBBOCompVDCUVtuning mirror (HR @ 45", 355 nm)Beamsplitter (for UV diode)Pinholepositive lensnegative lensprismhigh reflector (visible HR 400-700 nm)output couplerBBO crystalcompensator blockvisible dichroic mirror
3.7 Installation and setup of Acronis PXE ServerAcronis PXE Server allows the network booting of the Acronis Snap Deploy Agent, Acronis MasterImage Creator or Preinstallation Environment on target computers. Using Acronis PXE Serverconsiderably reduces the time required for booting the computers as compared to using bootablemedia. It also eliminates the need to have a technician onsite to install the bootable media into thesystem that must be booted. This allows for unattended scheduled deployment.Using Acronis PXE Server makes sense if there is a Dynamic Host Control Protocol (DHCP) server inyour network, so that the booting computers can automatically get IP addresses. Without DHCP, youcannot boot computers from PXE.We recommend that you have only one PXE server within a subnet to ensure predictability of thebooting computers behavior.3.7.1 Installation of Acronis PXE ServerTo install Acronis PXE Server:1. Run the Acronis Snap Deploy setup program2. Click Install Acronis PXE Server3. Follow the on screen Install Wizard instructions.Acronis PXE Server runs as a service immediately after installation. Later on it will automatically launchat each system restart. You can stop and start this program in the same way as other services.3.7.2 Setting up a computer to boot from PXEFor bare metal, it is enough that the machine’s BIOS supports network booting.On a machine that has an operating system on the hard disk, the BIOS must be configured so that thenetwork interface card is either the first boot device, or at least prior the Hard Drive device. Theexample below shows one of reasonable BIOS configurations. If you don’t insert bootable media, thecomputer will boot from the network.Setting up the BIOS (example) for network boot© Acronis, Inc 29
Page 1: MOPO-700metric Oscillator@ Spectra-
Page 5: Table ofContentsChapter 1 : Introdu
Page 9 and 10: IntroductionThe principal of operat
Page 11 and 12: APump Signal Idlerm355 nm 400 nm 71
Page 13 and 14: Figure 1-5: Schematic diagram of th
Page 15 and 16: Dichmic Beam SepamtionThe output be
Page 17 and 18: 1. All specifications subject to ch
Page 19 and 20: Use of controls or adjustments, or
Page 21 and 22: Focussed Back Reflection SakfyLaser
Page 24 and 25: Installing The ElectronicsControls
Page 26 and 27: Installing The MOPO-700Conimls and
Page 30 and 31: Figure 3-8: MOPO-710 Beam Path
Page 32 and 33: Figure3-9: Location of the alignmen
Page 34 and 35: fBLOCK I NOAPERTURETURN I NQMIRRORI
Page 36 and 37: OperationOperation of the MOPO-710O
Page 38 and 39: OPERATE ModeThe operate mode allows
Page 40 and 41: Figure4-3: Backlit panel options di
Page 42 and 43: SCAN SETUP ModeThis mode of allows
Page 44 and 45: Maintenance3Preventive MaintenanceT
Page 46 and 47: Customer ServiceAt Spectra-Physics
Page 48: Service CentersAustraliaSpectra-Phy

metric Oscillator - Beckman Institute Laser Resource Center

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?