metric Oscillator - Beckman Institute Laser Resource Center

More documents

Recommendations

Info

Figure3-9: Location of the alignment HeNe beam and alignment pinholes in laser cavity
PART 2 : Power Oscil/afor Alignment1. Place UVTMl in the mount. Adjust the position of the UVTMl such that thepump beam is centered on the UVTM2. After proper adjustment, the pump beamwill pass through the center of BS1. (See figure 3-10).2. Adjust the position of BS1 to steer the pump beam pickoff onto the photodiodedetector.3. Remove telescope lenses NL and PL out of the beam path. Use the adjustmentson UVTM 1 and 2 to center the pump beam through pinholes PH 3 and 4. Afterthis alignment, the pump beam will be centered on UVTM3.4. Fine tune the position of BS1 to recenter the pump beam pickoff onto thephotodiode detector.5. Remove the two pinholes, PH3 and PH46. Adjust the position of UVTM3 to overlap the pump beam and the HeNe beam onthe face of the BBO crystal. This is a crucial step for proper alignment.7. Adjust the position of UVTM4 to overlap the position of the pump beam andHeNe beam on the front face of NL.8. After this adjustment, the two beams will no longer be overlapped on the face ofthe BBO crystal. Reiterate step (6) and (7) until both beams simultaneously overlap on the face of the BBO crystal and on the negative lens.9. Adjust the position of UVTM5 base to center the pump beam onto the turningprism, P1.10. Position the pump beam onto the second turning prism, P2, by making adjustmentsto the position of P1. Likewise, position the pump beam onto the thirdturning prism, P3, by making adjustments to the position of P2.11. Steer the pump beam through the output aperture using P3. Tape a white cardover this output aperture and mark the position of the center of the pump beam.12. Install the negative lens of the telescope (NL) into the path of the pump beam.Adjust its horizontal position in order to overlap the center of the expanded pumpbeam with the HeNe beam on the blocking aperture. Tighten all mounting screwson the NL mount.13. Install the positive lens of the telescope (PL) in front of the negative lens. Adjustits horizontal and vertical position to reduce the pump beam diameter by a factorof 0.75 and to overlap the center of this beam with the HeNe beam at the inputface of he BBO crystal.14. Note the position of the pump beam on the white card taped to the outputaperture. Fine tune the horizontal position of the PL to recenter the beam to itsinitial position on the white card.15. Verify the size of the pump beam at the output of the telescope, just past NL.Translate PL in the vertical direction to achieve the same beam size as thatpresent at the output of P3 as well as NL.
Page 1: MOPO-700metric Oscillator@ Spectra-
Page 5: Table ofContentsChapter 1 : Introdu
Page 9 and 10: IntroductionThe principal of operat
Page 11 and 12: APump Signal Idlerm355 nm 400 nm 71
Page 13 and 14: Figure 1-5: Schematic diagram of th
Page 15 and 16: Dichmic Beam SepamtionThe output be
Page 17 and 18: 1. All specifications subject to ch
Page 19 and 20: Use of controls or adjustments, or
Page 21 and 22: Focussed Back Reflection SakfyLaser
Page 24 and 25: Installing The ElectronicsControls
Page 26 and 27: Installing The MOPO-700Conimls and
Page 28 and 29: Center the first IHS-355 on the pum
Page 30 and 31: Figure 3-8: MOPO-710 Beam Path
Page 34 and 35: fBLOCK I NOAPERTURETURN I NQMIRRORI
Page 36 and 37: OperationOperation of the MOPO-710O
Page 38 and 39: OPERATE ModeThe operate mode allows
Page 40 and 41: Figure4-3: Backlit panel options di
Page 42 and 43: SCAN SETUP ModeThis mode of allows
Page 44 and 45: Maintenance3Preventive MaintenanceT
Page 46 and 47: Customer ServiceAt Spectra-Physics
Page 48: Service CentersAustraliaSpectra-Phy

metric Oscillator - Beckman Institute Laser Resource Center

Create successful ePaper yourself

Delete template?

Save as template?