Hexavalent Chromium ATCM for Decorative and Hard Chrome

More documents

Recommendations

Info

Effective Date: October 24, 2007(1) No person shall operate a new facility unless it is locatedoutside of an area that is zoned for residential or mixed useand is located, as determined by the permitting agency, atleast 1,000 feet from (A) the boundary of any area that iszoned for residential or mixed use, or (B) any school or schoolunder construction.(A)A new facility shall be deemed to meet the requirementsspecified in this subsection (d)(1) if one of the followingcriteria is met, even if the facility does not meet therequirement at the time of initial startup (e.g., because of azoning change that occurs after the authority to construct isissued):1. The requirements specified in this subsection (d)(1) aremet at the time it is issued an authority to construct bythe permitting agency, and substantial use of theauthority to construct takes place within one year after itis issued; or2. The requirements specified in this subsection (d)(1) aremet at the time it is issued an authority to construct bythe permitting agency, and substantial use of theauthority to construct takes place before any zoningchange occurs that affects the operation’s ability to meetthe requirement at the time of initial startup.(2) During tank operation, each owner or operator of a new facilityshall control hexavalent chromium emissions discharged tothe atmosphere from that facility by reducing the hexavalentchromium emissions from the electroplating or anodizingtank(s) by installing a HEPA add-on air pollution controldevice. The measured emission rate of hexavalent chromiumshall be no more than 0.0011 milligrams per ampere-hour asmeasured after the HEPA add-on air pollution control device.(3) Prior to initial start-up the owner or operator of each newfacility shall conduct a site specific risk analysis in accordancewith the permitting agency’s procedures. The analysis shallbe submitted to the permitting agency.(4) Prior to initial startup, each new facility shall demonstrate tothe permitting agency that the new facility meets therequirements specified in this subsection (d) of this section93102.4.18
Effective Date: October 24, 2007(5) A facility is not required to comply with the requirement insection 93102.4(d)(2) to install a HEPA add-on air pollutioncontrol device if the facility is implementing an alternativemethod or methods that have been approved by the permittingagency as provided in section 93102.4(b)(3) and Health andSafety Code section 39666(f).(e)Notification Requirements for New and Modified Facilities.(1) Notification of Construction Reports.(A)(B)No person may construct or modify a facility, such that itbecomes a facility subject to sections 93102 to 93102.16,without submitting a notification of construction ormodification to the permitting agency and receivingapproval in advance to construct or modify the facility.The contents of the Notification of Construction Reportshall include the information contained in Appendix 4.(2) Alternative Notification Requirements: Instead of complyingwith the requirements in subpart (e)(1)(A) of this subsection, afacility may fulfill these requirements by complying with thepermitting agency's “New Source Review” requirements,provided similar information is obtained.NOTE: Authority cited: Sections 39600, 39601, 39650, 39658, 39659, and 39666, Health andSafety Code. Reference: Sections 39650, 39658, 39659, 39665, and 39666, Health and SafetyCode; and 40 CFR Part 63 Subpart N.§ 93102.5 Requirements that Apply to Existing, Modified, and NewHexavalent Chromium Plating or Chromic Acid AnodizingFacilities Beginning October 24, 2007.Each owner or operator of a hexavalent chromium plating orchromic acid anodizing facility shall comply with the followingrequirements on or after the dates specified below:(a)Removal of Add-on Pollution Control Device(s). No add-on airpollution control device(s) installed before October 24, 2007, shallbe removed or rendered inoperable unless it is replaced by an addonair pollution control device(s) meeting an emission rate of0.0015 milligrams per ampere-hour or less as measured after theadd-on air pollution control device or unless the facility is operatingunder an approved alternative method as provided insection 93102.4(b)(3) and Health and Safety Code section39666(f).19
Page 4 and 5: Effective Date: October 24, 2007con
Page 6 and 7: Effective Date: October 24, 2007she
Page 8 and 9: Effective Date: October 24, 2007(37
Page 11 and 12: Effective Date: October 24, 2007(53
Page 13 and 14: Effective Date: October 24, 2007(A)
Page 15 and 16: Effective Date: October 24, 2007Met
Page 17: Effective Date: October 24, 2007(B)
Page 21 and 22: Effective Date: October 24, 2007(4)
Page 23 and 24: Effective Date: October 24, 2007(b)
Page 27 and 28: Effective Date: October 24, 2007(b)
Page 29 and 30: Effective Date: October 24, 200745
Page 31 and 32: Effective Date: October 24, 2007Chr
Page 33 and 34: Effective Date: October 24, 2007(d)
Page 37 and 38: Effective Date: October 24, 2007tes
Page 39 and 40: Effective Date: October 24, 20073.
Page 41 and 42: Effective Date: October 24, 2007Tab
Page 45 and 46: Effective Date: October 24, 2007App
Page 47 and 48: Effective Date: October 24, 2007b)
Page 53 and 54: Effective Date: October 24, 2007San
Page 57: Effective Date: October 24, 2007App

Hexavalent Chromium ATCM for Decorative and Hard Chrome

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?