P3838_3 Mira Fino.pmd - QS Supplies

More documents

Recommendations

Info

AnticlockwiseIncreaseTemperatureClockwiseDecreaseTemperature1.7. Rotate the temperature spindle untilthe required temperature is obtained.Turn the spindle anticlockwise toincrease the temperature orclockwise to decrease thetemperature.If resistance is felt DO NOT USEFORCE to rotate the spindle as thisis the maximum obtainabletemperature from the shower controlwith the available hot water supplytemperature. FORCE will DAMAGEthe internal components of thecartridge assembly.1.8. Turn the flow knob off (fullyclockwise).1.9. Refit the temperature hub makingsure that the arrow on the hub alignswith the cut out.1.10. Refit the securing screw and thetemperature knob. Check that thetemperature knob can be rotatedfully in both directions.Temperature HubSecuring Screw1.11. Turn the flow knob fully anticlockwise(maximum flow) and check thetemperature is correct and theoverride functions correctly. Ifnecessary repeat the procedure untilthe correct temperature is achieved.Temperature HubTemperature Knob28
Temperature Override Button DisableThe Mira Fino incorporates a temperature override button that allows the user to overridethe preset maximum temperature. The following procedure can be used to disable theoverride button, limiting the maximum temperature available to the preset value. Thissetting is recommended for the young, the elderly, the infirm, or anyone inexperienced inthe correct operation of the controls.1. Ensure the shower control is turned off.2. Remove the temperature knob.3. Disable the temperature override button as follows;Fino B - on the rear of the temperature knob move the lever in the slot, this will eitherlock or release the button depending on how it had been previously set.Fino - on the rear of the temperature knob move the small plastic lever to lock it in theindent. Placing the lever in the indent will lock the override button.4. Install the temperature knob back on the valve.Fino BTemperatureOverride ButtonTemperatureOverride ButtonMove clockwiseto lockMove anticlockwisetounlockTemperatureOverride ButtonTemperatureOverride ButtonFinoMove the leverinto the indent willlock the overridebutton.Move the leverout of the indentwill unlock theoverride button.29
Page 1 and 2: SHOWER CONTROLInstallation &User Gu
Page 3 and 4: Section1 IntroductionThank you for
Page 5 and 6: 2. Mira Fino Built-in Shower Contro
Page 7 and 8: 5SPECIFICATIONSSpecificationsSectio
Page 9 and 10: Section6 Installation Requirements1
Page 11 and 12: Gravity fed showers - The shower co
Page 13 and 14: Pumped showers (inlet pumps)The sho
Page 15 and 16: 5. Install the inlet pipework.If ne
Page 17 and 18: Backplate5. Make good the wall surf
Page 19 and 20: 180 mm125 mm4. If installing the sh
Page 21 and 22: Compression NutOlive13. Stretch the
Page 23 and 24: Flow lever23. Remove the temperatur
Page 25 and 26: Laminated Panels and Shower Enclosu
Page 27: Section8 Commissioning1. Maximum Te
Page 31 and 32: Fino B1.1. Turn the flow lever anti
Page 33 and 34: Symptom6. Maximumblendtemperaturese
Page 35 and 36: 'C' WasherWave WasherHubTemperature
Page 37 and 38: Checkvalve/Strainer RenewalShould t
Page 39 and 40: Flow Cartridge RenewalShould the fl
Page 41 and 42: Section12Spare PartsMira Fino Spare
Page 43 and 44: Mira Fino B Spare Parts List451.01
Page 45 and 46: Notes45
Page 47 and 48: Notes47

P3838_3 Mira Fino.pmd - QS Supplies

Create successful ePaper yourself

Delete template?

Save as template?