Operation instruction - Asennustuotteet

More documents

Recommendations

Info

ABB i-bus ® KNXCommissioning3.2.14.1 Parameter windowA: Multiple operationIn this parameter window, all settings are undertaken for parameter windowA: Switching sequences.The explanations also apply for the Inputs B…X.This parameter window is visible if in parameter window Enable Inputs A…X,page 50, the option Switching sequences has been selected in parameterInput A.Enable communication object"Disable" 1 bitOptions: noyes• yes: The 1 bit Block communication object is enabled.This can be used to block the input.NoteIf the input is disabled and the option yes is selected with parameterCyclic sending, the last state is still sent regardless of the block.Using the communication object Block (No. 10), the physical input can bedisabled, but internal sending continues, i.e. the input terminals arephysically disconnected from the application program.The communication object Block (No.10) has no influence on manualoperation.© 2011 ABB STOTZ-KONTAKT GmbH 116
ABB i-bus ® KNXCommissioningCapacitive screeningOptions: up to 10 nF (standard)up to 20 nFup to 30 nFup to 40 nFThis parameter defines the degree of capacitive screening.Transmission errors can occur on extended cable lengths under certainconditions, e.g. in a 5 x 1.5 mm 2 cable, where two conductors are used as asignal line and one conductor is used for switching loads, it may result inmutual interference. If this proves to be the case in an installation, thesensitivity of the input is increased. It should be noted that the signalevaluation also slows down.Debounce timeOptions: 10/20/30/50/70/100/150 msDebouncing prevents unwanted multiple operations of the input, e.g. due tobouncing of the contact.What is the debounce time?If an edge is detected at an input, the input will react immediately tothis edge, e.g. by sending a telegram. At the same time, the durationof the debounce time T D starts. The signal on the input is notevaluated within the debounce time duration.The following example clarifies this:After detection of an edge on the input, further edges are ignored forthe debounce time T D .Connected contact typeOptions: closedopen• closed: The input is closed with actuation.• open: The input is opened with actuation.© 2011 ABB STOTZ-KONTAKT GmbH 117
Page 1:
kgABB i-bus ® KNXBinary Inputs BE/
Page 7 and 8:
ABB i-bus ® KNXGeneral1 GeneralAll
Page 9 and 10:
ABB i-bus ® KNXGeneral1.2 Product
Page 11 and 12:
ABB i-bus ® KNXDevice technology2
Page 13 and 14:
ABB i-bus ® KNXDevice technology2.
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
ABB i-bus ® KNXCommissioning3 Comm
Page 35 and 36:
ABB i-bus ® KNXCommissioning3.1.1.
Page 37 and 38:
Page 39 and 40:
ABB i-bus ® KNXCommissioningCopyTh
Page 41 and 42:
ABB i-bus ® KNXCommissioning3.2.1
Page 43 and 44:
ABB i-bus ® KNXCommissioningLimit
Page 45 and 46:
Page 47 and 48:
ABB i-bus ® KNXCommissioningSend o
Page 49 and 50:
Page 51 and 52:
ABB i-bus ® KNXCommissioningNo. Fu
Page 53 and 54:
ABB i-bus ® KNXCommissioningDesign
Page 55 and 56:
Page 57 and 58:
ABB i-bus ® KNXCommissioningWhat i
Page 59 and 60:
ABB i-bus ® KNXCommissioningWhat i
Page 61 and 62:
ABB i-bus ® KNXCommissioningCyclic
Page 63 and 64:
Page 65 and 66:
Page 67 and 68: ABB i-bus ® KNXCommissioningCommun
Page 69 and 70: ABB i-bus ® KNXCommissioningNo. Fu
Page 71 and 72: ABB i-bus ® KNXCommissioning3.2.9.
Page 73 and 74: ABB i-bus ® KNXCommissioningFuncti
Page 75 and 76: ABB i-bus ® KNXCommissioningDimmin
Page 79 and 80: ABB i-bus ® KNXCommissioning3.2.10
Page 81 and 82: ABB i-bus ® KNXCommissioningOperat
Page 89 and 90: ABB i-bus ® KNXCommissioningDistin
Page 91 and 92: ABB i-bus ® KNXCommissioningWhat i
Page 93 and 94: ABB i-bus ® KNXCommissioningsent v
Page 101 and 102: ABB i-bus ® KNXCommissioningStore
Page 109 and 110: ABB i-bus ® KNXCommissioningCapaci
Page 111 and 112: ABB i-bus ® KNXCommissioningNumber
Page 113 and 114: ABB i-bus ® KNXCommissioningSwitch
Page 117: ABB i-bus ® KNXCommissioning3.2.14
Page 121 and 122: ABB i-bus ® KNXCommissioningSend v
Page 129 and 130: ABB i-bus ® KNXCommissioningCapaci
Page 131 and 132: ABB i-bus ® KNXCommissioningMain C
Page 133 and 134: ABB i-bus ® KNXCommissioningChange
Page 135 and 136: ABB i-bus ® KNXCommissioningExampl
Page 141 and 142: ABB i-bus ® KNXPlanning and applic
Page 149: ABB i-bus ® KNXPlanning and applic
Page 152 and 153: ABB i-bus ® KNXAppendixA.2 Input4
Page 154 and 155: ABB i-bus ® KNXAppendixA.4 Code ta
Page 156 and 157: ABB i-bus ® KNXAppendixA.6 Notes©
Page 158: ABB i-bus ® KNXAppendixA.8 Notes©
show all

Operation instruction - Asennustuotteet

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?