Operation instruction - Asennustuotteet

More documents

Recommendations

Info

ABB i-bus ® KNXCommissioningLong operation after …Options: 0.3/0.4/0.5/0.6/0.8 s1/1.2/1.5 s2/3/4/5/6/7/8/9/10 sHere the time period T L , after which an actuation is considered a “long”operation, is defined.NoteThe remaining parameter descriptions can be found in the parameterDistinction between short and long operation – no,page 55.© 2011 ABB STOTZ-KONTAKT GmbH 62
ABB i-bus ® KNXCommissioning3.2.8.1.3 Special functionFault monitoring inputNoteFor the operating mode Fault monitoring input the, options must beadapted in comparison to the standard settings.The options for Fault monitoring input are listed separately in the following.In this chapter, only the parameters, which are relevant for optimum Faultmonitoring input performance, are listed.All descriptions of the parameter should be taken from parameter windowA: Switch sensor, page 53.Debounce timeOptions:Fault monitoring option:10/20/30/50/70/100/150 ms 50 msDistinction between short andlong operationOptions:yes/noActivate minimum signal timeOptions:yes/noFault monitoring option:noFault monitoring option:yesOn closing the contactin value x 0.1 s [1…65,535]Options:Fault monitoring option:1…10…65,535 2On opening the contactin value x 0.1 s [1…65,535]Options:Fault monitoring option:1…10…65,535 2NoteDepending on the system type, a minimum signal duration settingof, e.g. two seconds is recommended. With the evaluation forexample of coupling switches, generator switches or incomingcircuit-breakers from switchgear systems, a smaller minimumsignal time of 100 ms, for example, may be necessary.It is essential to co-ordinate the switching times with the operator!Smaller signal/switch times may be required depending on thesystem.© 2011 ABB STOTZ-KONTAKT GmbH 63
Page 1:
kgABB i-bus ® KNXBinary Inputs BE/
Page 7 and 8:
ABB i-bus ® KNXGeneral1 GeneralAll
Page 9 and 10:
ABB i-bus ® KNXGeneral1.2 Product
Page 11 and 12:
ABB i-bus ® KNXDevice technology2
Page 13 and 14: ABB i-bus ® KNXDevice technology2.
Page 33 and 34: ABB i-bus ® KNXCommissioning3 Comm
Page 35 and 36: ABB i-bus ® KNXCommissioning3.1.1.
Page 39 and 40: ABB i-bus ® KNXCommissioningCopyTh
Page 41 and 42: ABB i-bus ® KNXCommissioning3.2.1
Page 43 and 44: ABB i-bus ® KNXCommissioningLimit
Page 47 and 48: ABB i-bus ® KNXCommissioningSend o
Page 51 and 52: ABB i-bus ® KNXCommissioningNo. Fu
Page 53 and 54: ABB i-bus ® KNXCommissioningDesign
Page 57 and 58: ABB i-bus ® KNXCommissioningWhat i
Page 61 and 62: ABB i-bus ® KNXCommissioningCyclic
Page 63: ABB i-bus ® KNXCommissioning3.2.8.
Page 67 and 68: ABB i-bus ® KNXCommissioningCommun
Page 73 and 74: ABB i-bus ® KNXCommissioningFuncti
Page 75 and 76: ABB i-bus ® KNXCommissioningDimmin
Page 81 and 82: ABB i-bus ® KNXCommissioningOperat
Page 89 and 90: ABB i-bus ® KNXCommissioningDistin
Page 93 and 94: ABB i-bus ® KNXCommissioningsent v
Page 101 and 102: ABB i-bus ® KNXCommissioningStore
Page 109 and 110: ABB i-bus ® KNXCommissioningCapaci
Page 111 and 112: ABB i-bus ® KNXCommissioningNumber
Page 113 and 114: ABB i-bus ® KNXCommissioningSwitch
Page 115 and 116:
ABB i-bus ® KNXCommissioningNo. Fu
Page 117 and 118:
ABB i-bus ® KNXCommissioning3.2.14
Page 119 and 120:
ABB i-bus ® KNXCommissioningCapaci
Page 121 and 122:
ABB i-bus ® KNXCommissioningSend v
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
ABB i-bus ® KNXCommissioningCapaci
Page 131 and 132:
ABB i-bus ® KNXCommissioningMain C
Page 133 and 134:
ABB i-bus ® KNXCommissioningChange
Page 135 and 136:
ABB i-bus ® KNXCommissioningExampl
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
ABB i-bus ® KNXPlanning and applic
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149:
Page 152 and 153:
ABB i-bus ® KNXAppendixA.2 Input4
Page 154 and 155:
ABB i-bus ® KNXAppendixA.4 Code ta
Page 156 and 157:
ABB i-bus ® KNXAppendixA.6 Notes©
Page 158:
ABB i-bus ® KNXAppendixA.8 Notes©
show all

Operation instruction - Asennustuotteet

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?