1.0 - SATA-IO

More documents

Recommendations

Info

• Serial ATA cables, eSATA to SATA cables if testing eSATA devices• Vendor supplied SATA HDD/ATAPI Product Under Test (P.U.T.)• Proper media compatible with ATAPI drives: Compatible blank RW media for read-writedrives, or a known Data Disc (Read(10) compatible) for read-only drivesLast ModificationThis specifies the date of the last modification to this test.Test SetupThe setup section describes the initial configuration of the test environment. Small changes in theconfiguration are not included, and are generally presented in the test procedure section.Since the main test setup for all the tests are the same therefore this setup is listed in Appendix BProcedureThe procedure section of the test description contains the systematic instructions for carrying outthe test. It provides a systematic approach to testing, and may be interspersed with observableresults.Since the main test procedure for all the tests are the same therefore this procedure is listed inAppendix BObservable ResultsThis section lists the specific observables that can be examined by the tester in order to verify thatthe P.U.T. is operating properly. When multiple values for an observable are possible, this sectionprovides a short discussion on how to interpret them. The determination of a pass or fail outcomefor a particular test is generally based on the successful (or unsuccessful) detection of a specificobservable resultGenerally, four result categories exist:1. “PASSED”: means the P.U.T. has fulfilled the required criteria via LeCroy TestProcedure.2. “FAILED”: means at least one compliance criterion is not met.3. “N/A”: means the test is not applicable to the P.U.T. and is generally derived from thelist of supported features of P.U.T. in Identify Page data.12 Device Digital MOI for LeCroy STX Bus Analyzer
4. BLANK: means a severe error is happened during the execution of test project onLeCroy Host Emulator. This may be caused by a loose connection, power failure orsimilar problems. In this case, test procedure shall be repeated to obtain a reliable result.It is highly recommended to check mechanical connections before re-running the test. Insome rare situations, an internal error in P.U.T. or Host Emulator Engine may lead tothis problem and causes the BLANK result to be repeated in next executions. The bestand most reliable solution to this problem is to switch off the P.U.T. and LeCroy HostEmulator and switch on back before retrying the test.Possible ProblemsThis section contains a description of known issues with the test procedure, which may affect testresults in certain situations. It may also refer the reader to test suite appendices and/or otherexternal sources that may provide more detail regarding these issues.ReferencesThe following documents are referenced in this text:1. Serial ATA Revision 2.62. SATA-IO Interoperability Rev 1.3 Program Policy Document3. SATA-IO Interoperability Rev 1.3 Version 1.0 Unified Test Document13 Digital MOI for LeCroy STX Bus Analyzer
Page 1 and 2: 19 March 2009 Version 1.00Serial AT
Page 4 and 5: IPM-10: Slumber State exit latency
Page 6 and 7: tests• Changed wording on IPM-01,
Page 8 and 9: checking specified bits• Added ad
Page 10 and 11: UDMA and MWDMA ifsupported. Note th
Page 14 and 15: Test Procedures14 Device Digital MO
Page 16 and 17: Measurement Tolerance: +/- 13.337 n
Page 18 and 19: Observable Results1. Click the “V
Page 20 and 21: o Device latency is verified to be
Page 22 and 23: o Supported speeds in Identify page
Page 24 and 25: • A Pair of WRITE/READ DMA comman
Page 26 and 27: GTR-04 Word 93 contentsPurposeTo ve
Page 28 and 29: GTR-05 Unrecognized FIS receiptPurp
Page 30 and 31: NCQ-01 Forced Unit AccessPurposeTo
Page 32 and 33: NCQ-02 Read Log Ext Log Page 10h Su
Page 34 and 35: NCQ-03 Intermix of Legacy and NCQ C
Page 36 and 37: esult is reported if one of the abo
Page 38 and 39: NCQ-04 Device Response to Malformed
Page 40 and 41: ERR bit in Status register set DF b
Page 42 and 43: NCQ-05 DMA Setup Auto-activatePurpo
Page 44 and 45: SSP-01 Initialize Device Parameters
Page 46 and 47: SSP-02 Read/Write Stream Error LogP
Page 48 and 49: 4) A Write Uncorrectable EXT with U
Page 50 and 51: SSP-03 Security Mode StatePurposeTo
Page 52 and 53: Possible ProblemsIt is advisable to
Page 54 and 55: o SSP04-02.stc (For 48-bit address
Page 56 and 57: • A COMRESET is issued.• Anothe
Page 58 and 59: 4) For ATAPI devices:• An IDENTIF
Page 60 and 61: o Existing and complete execution o
Page 62 and 63:
• A COMRESET is issued.• Anothe
Page 64 and 65:
• A SET FEATURES command with the
Page 66 and 67:
• A COMRESET is issued.• Anothe
Page 68 and 69:
5) Another IDENTIFY DEVICE command
Page 70 and 71:
o Bit 9 of WORD 76 of Identify Page
Page 72 and 73:
o Bit 9 of WORD 76 Identify Page da
Page 74 and 75:
3) An IDENTIFY or IDENTIFY PACKET D
Page 76 and 77:
IPM-04 : NAK of requests when suppo
Page 78 and 79:
IPM-05 Device Response to PMREQ_PPu
Page 80 and 81:
IPM-06 Device Response to PMREQ_SPu
Page 82 and 83:
IPM-07 Default Setting for Device I
Page 84 and 85:
IPM-08 Device initiated power manag
Page 86 and 87:
IPM-09: Partial State exit latency
Page 88 and 89:
IPM-10: Slumber State exit latency
Page 90 and 91:
IPM-11: Speed matching upon resume
Page 92 and 93:
“PASSED”. In the case that no d
Page 94 and 95:
5. Select compliance type, Device c
Page 96 and 97:
Host and Capture Settings96 Device
Page 98:
Post ProcessingIf the device does n
show all

1.0 - SATA-IO

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?