1.0 - SATA-IO

More documents

Recommendations

Info

4) A Write Uncorrectable EXT with Uncorrectable options = 55h command issent5) A Configure Stream command is sent6) A Read Stream command is sent with LBA address pointed at location ofuncorrectable error7) A Read Log Ext 22h is sent.• Verify contents of Log page that error has occurred8) A Configure Stream command is sent9) A Read Stream command is sent with LBA address pointed at location ofECC error10) A COMRESET is sent11) A Read Log Ext 22h is sent• Post process:o Existing and complete execution of IDENTIFY DEVICE Command and existenceof READ LOG EXT commands in the trace is checked to verify the properexecution of test project. “ERROR” result is reported if any of the above is notexecuted properly.o Bit 6 of WORD 78 of Identify Page data is checked and “N/A” result is reported ifdevice does not support software settings preservation.o Bit 4 of WORD 84 of Identify Page data is checked and “N/A” result is reported ifdevice does not support streaming.o For SSP02-01, if READ LONG and WRITE LONG commands are aborted bydevice, test is skipped.o For SSP02-02, Bit 0 of WORD 82 and bit 0 of WORD 84 of Identify Page data arechecked and test is skipped if device does not support SMART commands andSMART error loggingo For SSP02-03, Bit 2 of WORD 120 of Identify Page data is checked and test isskipped if device does not support WRITE UNCORRECTABLE EXT command.o Complete execution of CONFIGURE STREAM, READ STREAM DMA, and allREAD LOG EXT commands are checked to verify the proper execution of testproject.o The payloads of the second and third READ LOG EXT are compared to be thesame.( log page 22h)o If all 3 projects are skipped, “N/A” test result is reported.o If any of the above criteria is not fulfilled, “FAILED” result will be reported,otherwise the test would be “PASSED”.Observable Results1. Click the “View” button to see a report of the test. A failing test may be viewed by going tothe C:\Program Files\Catalyst\<strong>SATA</strong>2.xx\LOG directory and double clicking on theappropriate test for analysis.48 Device Digital MOI for LeCroy STX Bus Analyzer
Possible ProblemsIt is advisable to set the Bus Analyzer to the same speed as the device, either 1.5G or 3G, ratherthan setting the Bus Analyzer to ‘Auto Detect’ speed. It has been observed that the tests can beperformed properly with the Bus Analyzer set to ‘Auto-Detect’ speed.49 Digital MOI for LeCroy STX Bus Analyzer
Page 1 and 2: 19 March 2009 Version 1.00Serial AT
Page 4 and 5: IPM-10: Slumber State exit latency
Page 6 and 7: tests• Changed wording on IPM-01,
Page 8 and 9: checking specified bits• Added ad
Page 10 and 11: UDMA and MWDMA ifsupported. Note th
Page 12 and 13: • Serial ATA cables, eSATA to SAT
Page 14 and 15: Test Procedures14 Device Digital MO
Page 16 and 17: Measurement Tolerance: +/- 13.337 n
Page 18 and 19: Observable Results1. Click the “V
Page 20 and 21: o Device latency is verified to be
Page 22 and 23: o Supported speeds in Identify page
Page 24 and 25: • A Pair of WRITE/READ DMA comman
Page 26 and 27: GTR-04 Word 93 contentsPurposeTo ve
Page 28 and 29: GTR-05 Unrecognized FIS receiptPurp
Page 30 and 31: NCQ-01 Forced Unit AccessPurposeTo
Page 32 and 33: NCQ-02 Read Log Ext Log Page 10h Su
Page 34 and 35: NCQ-03 Intermix of Legacy and NCQ C
Page 36 and 37: esult is reported if one of the abo
Page 38 and 39: NCQ-04 Device Response to Malformed
Page 40 and 41: ERR bit in Status register set DF b
Page 42 and 43: NCQ-05 DMA Setup Auto-activatePurpo
Page 44 and 45: SSP-01 Initialize Device Parameters
Page 46 and 47: SSP-02 Read/Write Stream Error LogP
Page 50 and 51: SSP-03 Security Mode StatePurposeTo
Page 52 and 53: Possible ProblemsIt is advisable to
Page 54 and 55: o SSP04-02.stc (For 48-bit address
Page 56 and 57: • A COMRESET is issued.• Anothe
Page 58 and 59: 4) For ATAPI devices:• An IDENTIF
Page 60 and 61: o Existing and complete execution o
Page 64 and 65: • A SET FEATURES command with the
Page 68 and 69: 5) Another IDENTIFY DEVICE command
Page 70 and 71: o Bit 9 of WORD 76 of Identify Page
Page 72 and 73: o Bit 9 of WORD 76 Identify Page da
Page 74 and 75: 3) An IDENTIFY or IDENTIFY PACKET D
Page 76 and 77: IPM-04 : NAK of requests when suppo
Page 78 and 79: IPM-05 Device Response to PMREQ_PPu
Page 80 and 81: IPM-06 Device Response to PMREQ_SPu
Page 82 and 83: IPM-07 Default Setting for Device I
Page 84 and 85: IPM-08 Device initiated power manag
Page 86 and 87: IPM-09: Partial State exit latency
Page 88 and 89: IPM-10: Slumber State exit latency
Page 90 and 91: IPM-11: Speed matching upon resume
Page 92 and 93: “PASSED”. In the case that no d
Page 94 and 95: 5. Select compliance type, Device c
Page 96 and 97: Host and Capture Settings96 Device
Page 98:
Post ProcessingIf the device does n
show all

1.0 - SATA-IO

Create successful ePaper yourself

Delete template?

Save as template?