1.0 - SATA-IO

More documents

Recommendations

Info

checking specified bits• Added additional supportedtest tools (Sierra M6-4, andSTX-131) for compliancetesting0.99E 01/30/2009 • Title page revisions - dates,revision level changes from1.2 to 1.3; version from<strong>1.0</strong>RC back to 0.99E• Changed zip code, supportemail, phone number• Changed UTD1.2 to UTD1.3 throughout document• Made changes to resourcerequirements• GTR-01 removed checkingspecified bits (upon failuresee Appendix C)• GTR-02 removed checkingspecified bits from MOI1. GTR-03 changed transferlength sizes from logicalblock sizes to KB for easierunderstanding for ATAPIdrives2. NCQ-02 changed so thatthe MOI matched with testshowing successful dataread and confirmation fromlog page 0h3. IPM-11 added to Table ofContents (already in theMOI and software);renumbered pages in MOIas required4. IPM-03 and IPM-11 Pass,Fail, and “NA” postprocessing critieria wordingwas made simpler andsimilar5. IPM-08 MOI updated to8 Device Digital MOI for LeCroy STX Bus Analyzer
match tests with 2STANDBY-IMMEDIATES instead of1; added note that a testcould take longer than 400seconds6. Appendix A: changed textto reflect mandatory versusfeature dependent tests7. Appendix B: changed UTDversion to 1.3; change 2.8xto 2.81• Added Appendix C forGTR-01 true failureverification and manual testprocedure for SSP-02 bothfor software release 2.81• In transistioning fromUTD1.2 to UTD 1.3 atApril 2008 Plugfest thefollowing tests werechanges needed to be orhave been done to the MOIfor UTD1.3 - GTR-01,GTR-02, GTR-03, NCQ-02, SSP-06, IPM-03 (twoareas), IPM-04, IPM-08,IPM-11.In Release .99C of the MOIthe following tests had beenchnaged prior to IW#5 GTRtests 1-3 were changed forRead Sector, qualified bits andDMA modes, NCQ-02 hadconfirmed changes ; IPM-03and 11 and loop changes;Pass/Fail clarification andtesting for PM Partial andSlumber; IPM-04 had Pass/Failclarification; IPM-08 requiredputting a drive into STANDBYIMMEDIATE for ATAPI driveas well as HDDs.Lastly SSP-06involved testing for both9 Digital MOI for LeCroy STX Bus Analyzer
Page 1 and 2: 19 March 2009 Version 1.00Serial AT
Page 4 and 5: IPM-10: Slumber State exit latency
Page 6 and 7: tests• Changed wording on IPM-01,
Page 10 and 11: UDMA and MWDMA ifsupported. Note th
Page 12 and 13: • Serial ATA cables, eSATA to SAT
Page 14 and 15: Test Procedures14 Device Digital MO
Page 16 and 17: Measurement Tolerance: +/- 13.337 n
Page 18 and 19: Observable Results1. Click the “V
Page 20 and 21: o Device latency is verified to be
Page 22 and 23: o Supported speeds in Identify page
Page 24 and 25: • A Pair of WRITE/READ DMA comman
Page 26 and 27: GTR-04 Word 93 contentsPurposeTo ve
Page 28 and 29: GTR-05 Unrecognized FIS receiptPurp
Page 30 and 31: NCQ-01 Forced Unit AccessPurposeTo
Page 32 and 33: NCQ-02 Read Log Ext Log Page 10h Su
Page 34 and 35: NCQ-03 Intermix of Legacy and NCQ C
Page 36 and 37: esult is reported if one of the abo
Page 38 and 39: NCQ-04 Device Response to Malformed
Page 40 and 41: ERR bit in Status register set DF b
Page 42 and 43: NCQ-05 DMA Setup Auto-activatePurpo
Page 44 and 45: SSP-01 Initialize Device Parameters
Page 46 and 47: SSP-02 Read/Write Stream Error LogP
Page 48 and 49: 4) A Write Uncorrectable EXT with U
Page 50 and 51: SSP-03 Security Mode StatePurposeTo
Page 52 and 53: Possible ProblemsIt is advisable to
Page 54 and 55: o SSP04-02.stc (For 48-bit address
Page 56 and 57: • A COMRESET is issued.• Anothe
Page 58 and 59:
4) For ATAPI devices:• An IDENTIF
Page 60 and 61:
o Existing and complete execution o
Page 62 and 63:
• A COMRESET is issued.• Anothe
Page 64 and 65:
• A SET FEATURES command with the
Page 66 and 67:
• A COMRESET is issued.• Anothe
Page 68 and 69:
5) Another IDENTIFY DEVICE command
Page 70 and 71:
o Bit 9 of WORD 76 of Identify Page
Page 72 and 73:
o Bit 9 of WORD 76 Identify Page da
Page 74 and 75:
3) An IDENTIFY or IDENTIFY PACKET D
Page 76 and 77:
IPM-04 : NAK of requests when suppo
Page 78 and 79:
IPM-05 Device Response to PMREQ_PPu
Page 80 and 81:
IPM-06 Device Response to PMREQ_SPu
Page 82 and 83:
IPM-07 Default Setting for Device I
Page 84 and 85:
IPM-08 Device initiated power manag
Page 86 and 87:
IPM-09: Partial State exit latency
Page 88 and 89:
IPM-10: Slumber State exit latency
Page 90 and 91:
IPM-11: Speed matching upon resume
Page 92 and 93:
“PASSED”. In the case that no d
Page 94 and 95:
5. Select compliance type, Device c
Page 96 and 97:
Host and Capture Settings96 Device
Page 98:
Post ProcessingIf the device does n
show all

1.0 - SATA-IO

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?