1.0 - SATA-IO

More documents

Recommendations

Info

IPM-10: Slumber State exit latency (Device-Initiated) ................................................................ 88IPM-11: Speed matching upon resume (Device-Initiated) .......................................................... 90Appendix A....................................................................................................................................... 93Test Selection................................................................................................................................ 93Appendix B....................................................................................................................................... 93SATA I/O Digital Compliance Test Setup & Procedure.............................................................. 93Test Setup: .................................................................................................................................... 93Test Procedure: ............................................................................................................................. 93Appendix C ………………………………………………………………………………………..94GTR-01: False Failure Verification for Software Release 2.81: .................................................. 94SSP-02: Manual Test Procedure for Software Release 2.81 ........................................................ 94iv Device Digital MOI for LeCroy STX Bus Analyzer
RECORD of CHANGESRevision Date Comments0.1 02/08/2006 Initial draft0.9 RC1 07/31/2006 Added IPM-01,-02,-03.Reformatted cover.Merged two MOI in to one0.9 RC2 8/3/2006 All test procedures have beenupdated.0.9 RC3 8/14/2006 • Removed OOB tests.• Updated the Purpose,Discussion and Procedure• Added actual measurementnumbers to the report• Changed PHY reset toCOMRESET• Added clarification inseveral places0.9 RC4 9/5/2006 • Changed “WakeupRequest” to COMWAKE• Removed CHECK POWERMODE command fromIPM tests• Restructured IPM tests0.9 RC5 11/5/2006 • Reviewed with JeffWolford• Restructured GTR-03 toreflect implementation inUTD v.93• Removed “MeasurementTolerance” from GTR,NCQ, and SSP tests.• Clarified “MeasurementTolerance” for IPM tests0.9 RC5 1/25/07 • Reviewed during SATA-IOconference call• Changed ATAPI testingprocedures for relevant SSP5 Digital MOI for LeCroy STX Bus Analyzer
Page 1 and 2: 19 March 2009 Version 1.00Serial AT
Page 6 and 7: tests• Changed wording on IPM-01,
Page 8 and 9: checking specified bits• Added ad
Page 10 and 11: UDMA and MWDMA ifsupported. Note th
Page 12 and 13: • Serial ATA cables, eSATA to SAT
Page 14 and 15: Test Procedures14 Device Digital MO
Page 16 and 17: Measurement Tolerance: +/- 13.337 n
Page 18 and 19: Observable Results1. Click the “V
Page 20 and 21: o Device latency is verified to be
Page 22 and 23: o Supported speeds in Identify page
Page 24 and 25: • A Pair of WRITE/READ DMA comman
Page 26 and 27: GTR-04 Word 93 contentsPurposeTo ve
Page 28 and 29: GTR-05 Unrecognized FIS receiptPurp
Page 30 and 31: NCQ-01 Forced Unit AccessPurposeTo
Page 32 and 33: NCQ-02 Read Log Ext Log Page 10h Su
Page 34 and 35: NCQ-03 Intermix of Legacy and NCQ C
Page 36 and 37: esult is reported if one of the abo
Page 38 and 39: NCQ-04 Device Response to Malformed
Page 40 and 41: ERR bit in Status register set DF b
Page 42 and 43: NCQ-05 DMA Setup Auto-activatePurpo
Page 44 and 45: SSP-01 Initialize Device Parameters
Page 46 and 47: SSP-02 Read/Write Stream Error LogP
Page 48 and 49: 4) A Write Uncorrectable EXT with U
Page 50 and 51: SSP-03 Security Mode StatePurposeTo
Page 52 and 53: Possible ProblemsIt is advisable to
Page 54 and 55:
o SSP04-02.stc (For 48-bit address
Page 56 and 57:
• A COMRESET is issued.• Anothe
Page 58 and 59:
4) For ATAPI devices:• An IDENTIF
Page 60 and 61:
o Existing and complete execution o
Page 62 and 63:
Page 64 and 65:
• A SET FEATURES command with the
Page 66 and 67:
Page 68 and 69:
5) Another IDENTIFY DEVICE command
Page 70 and 71:
o Bit 9 of WORD 76 of Identify Page
Page 72 and 73:
o Bit 9 of WORD 76 Identify Page da
Page 74 and 75:
3) An IDENTIFY or IDENTIFY PACKET D
Page 76 and 77:
IPM-04 : NAK of requests when suppo
Page 78 and 79:
IPM-05 Device Response to PMREQ_PPu
Page 80 and 81:
IPM-06 Device Response to PMREQ_SPu
Page 82 and 83:
IPM-07 Default Setting for Device I
Page 84 and 85:
IPM-08 Device initiated power manag
Page 86 and 87:
IPM-09: Partial State exit latency
Page 88 and 89:
IPM-10: Slumber State exit latency
Page 90 and 91:
IPM-11: Speed matching upon resume
Page 92 and 93:
“PASSED”. In the case that no d
Page 94 and 95:
5. Select compliance type, Device c
Page 96 and 97:
Host and Capture Settings96 Device
Page 98:
Post ProcessingIf the device does n
show all

1.0 - SATA-IO

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?