1.0 - SATA-IO

More documents

Recommendations

Info

esult is reported if one of the above commands is missed and/or not executedcompletely.o The device response to Legacy command is checked that should be a RD2H with:1) ERR bit in Status register set2) DRQ bit in status register is cleared3) DF bit in status register is cleared4) DRDY bit in status register is set5) BSY bit in Status register clearedo The existence of Set Device Bit FIS after issuance of READ LOG EXT command ischecked. Also its contents are checked to be:1) ERR bit in Status register cleared2) DRDY bit in Status register is set3) DF bit in Status register is cleared4) Interrupt bit (I) cleared5) SActive Register equals to ‘FFFFFFFFh’o NQ Bit in returned log page (payload of READ LOG EXT) is verified to be seto If any of the above criteria is not fulfilled, “FAILED” result is reported.• NCQ03-03.sts:o Existing and complete execution of WRITE SECTOR and READ LOG EXTcommands in the trace are checked to verify the proper execution of test project.“ERROR” result is reported if one of the above commands is missed and/or notexecuted completely.o The device response to Legacy command is checked that should be a RD2H with:1) ERR bit in Status register set2) DRQ bit in status register is cleared3) DF bit in status register is cleared4) DRDY bit in status register is set5) BSY bit in Status register clearedo The existence of Set Device Bit FIS after issuance of READ LOG EXT command ischecked. Also its contents are checked to be:1) ERR bit in Status register cleared2) DRDY bit in Status register is set3) DF bit in Status register is cleared4) Interrupt bit (I) cleared5) SActive Register equals to ‘FFFFFFFFh’o NQ Bit in returned log page (payload of READ LOG EXT) is verified to be seto If any of the above criteria is not fulfilled, “FAILED” result is reported.o If all four post-process phases are completed without any problem, “PASSED”result is reported.Observable Results1. Click the “View” button to see a report of the test. A failing test may be viewed by going tothe C:\Program Files\Catalyst\<strong>SATA</strong>2.xx\LOG directory and double clicking on theappropriate test for analysis.36 Device Digital MOI for LeCroy STX Bus Analyzer
Possible ProblemsIt is advisable to set the Bus Analyzer to the same speed as the device, either 1.5G or 3G, ratherthan setting the Bus Analyzer to ‘Auto Detect’ speed. It has been observed that the tests can beperformed properly with the Bus Analyzer set to ‘Auto-Detect’ speed.37 Digital MOI for LeCroy STX Bus Analyzer
Page 1 and 2: 19 March 2009 Version 1.00Serial AT
Page 4 and 5: IPM-10: Slumber State exit latency
Page 6 and 7: tests• Changed wording on IPM-01,
Page 8 and 9: checking specified bits• Added ad
Page 10 and 11: UDMA and MWDMA ifsupported. Note th
Page 12 and 13: • Serial ATA cables, eSATA to SAT
Page 14 and 15: Test Procedures14 Device Digital MO
Page 16 and 17: Measurement Tolerance: +/- 13.337 n
Page 18 and 19: Observable Results1. Click the “V
Page 20 and 21: o Device latency is verified to be
Page 22 and 23: o Supported speeds in Identify page
Page 24 and 25: • A Pair of WRITE/READ DMA comman
Page 26 and 27: GTR-04 Word 93 contentsPurposeTo ve
Page 28 and 29: GTR-05 Unrecognized FIS receiptPurp
Page 30 and 31: NCQ-01 Forced Unit AccessPurposeTo
Page 32 and 33: NCQ-02 Read Log Ext Log Page 10h Su
Page 34 and 35: NCQ-03 Intermix of Legacy and NCQ C
Page 38 and 39: NCQ-04 Device Response to Malformed
Page 40 and 41: ERR bit in Status register set DF b
Page 42 and 43: NCQ-05 DMA Setup Auto-activatePurpo
Page 44 and 45: SSP-01 Initialize Device Parameters
Page 46 and 47: SSP-02 Read/Write Stream Error LogP
Page 48 and 49: 4) A Write Uncorrectable EXT with U
Page 50 and 51: SSP-03 Security Mode StatePurposeTo
Page 52 and 53: Possible ProblemsIt is advisable to
Page 54 and 55: o SSP04-02.stc (For 48-bit address
Page 56 and 57: • A COMRESET is issued.• Anothe
Page 58 and 59: 4) For ATAPI devices:• An IDENTIF
Page 60 and 61: o Existing and complete execution o
Page 64 and 65: • A SET FEATURES command with the
Page 68 and 69: 5) Another IDENTIFY DEVICE command
Page 70 and 71: o Bit 9 of WORD 76 of Identify Page
Page 72 and 73: o Bit 9 of WORD 76 Identify Page da
Page 74 and 75: 3) An IDENTIFY or IDENTIFY PACKET D
Page 76 and 77: IPM-04 : NAK of requests when suppo
Page 78 and 79: IPM-05 Device Response to PMREQ_PPu
Page 80 and 81: IPM-06 Device Response to PMREQ_SPu
Page 82 and 83: IPM-07 Default Setting for Device I
Page 84 and 85: IPM-08 Device initiated power manag
Page 86 and 87:
IPM-09: Partial State exit latency
Page 88 and 89:
IPM-10: Slumber State exit latency
Page 90 and 91:
IPM-11: Speed matching upon resume
Page 92 and 93:
“PASSED”. In the case that no d
Page 94 and 95:
5. Select compliance type, Device c
Page 96 and 97:
Host and Capture Settings96 Device
Page 98:
Post ProcessingIf the device does n
show all

1.0 - SATA-IO

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?