Pulse XT 25e Manual - E-flite

More documents

Recommendations

Info

Required EquipmentRadioYou will need a minimum of a 4-channel radio for this model. A completeradio system can be purchased or, if you have a suitable transmitter, just theairborne components will be required.Complete SystemSpektrum DX6i 2.4GHz DSM2 radio systemSPM6600(4) JR SPORT MN48 mini servos JSP20040(2) JR SPORT 6” servo extension leads JSP98110(2) JR SPORT 3” servo extension leads JSP98100-or (1) Y-harness (JSP98020) if not using the dual aileron functionAirborne ComponentsSpektrum AR6200 DSM2 2.4GHz receiverSPMAR6200(4) JR SPORT MN48 mini servos JSP20040(2) JR SPORT 6” servo extension leads JSP98110(2) JR SPORT 3” servo extension leads JSP98100-or (1) y-harness (JSP98020) if not using the dual aileron functionMotorThe Pulse XT 25e is designed to accept either the E-flite Power 25 or Power 32Brushless Outrunner motors and comes complete with the hardware for eitherinstallation.Required Tools and AdhesivesE-flite parkflyer tool assortment1/16 (1.5mm) in drill bitE-flite 1/4" nut driver5/64 in (2mm) drill bit7/64” balldriver Dremel rotary tool12 minute epoxy High speed cutoff wheelThin CA (cyanoacrylate)High speed rotary cutterCanopy glueLow-tack tapePin drillClear tapeTapered reamerFelt-tip pen3/32” ball driver Tongue depressors#0 Philips screwdriver Mixing sticks#1 Philips screwdriver Dental flossThreadlockFor Float installation11/64 in (4.5mm) drill bitFlat fileDrillRuler1.5mm Allen wrench (included with EFLA500)Sport Motor SetupE-flite Power 25 brushless outrunner motorE-flite 40-Amp Pro Brushless ESCE-flite 3200mAh 3S LiPo battery packAPC 12 x 8E propellerHigh Power Motor SetupE-flite Power 32 brushless outrunner motorE-flite 60-Amp Pro Brushless ESCE-flite 3200mAh 4s LiPo battery packAPC 13 x 6.5E propellerEFLM4025AEFLA1040EFLB32003SAPC12080EEFLM4032AEFLA1060EFLB32004SAPC13065EOptional AccessoriesE-flite 25-size Float SetEFLA500E-flite 1 - 5 cell LiPo charger with balancer EFLC505Power MeterEFLA110LiPo Charge Safe Charging BagKSJ1821JR MatchMakerJRPA91536” flex cable (required for float installation) SUL5084
Landing Gear Assembly and InstallationRequired parts:FuselageMain landing gear (wheels installed)Wheel pants(2) 6-32 x 1/2" socket head bolts(2) #6 steel washers(4) #2 x 3/8” sheet metal screwsΟ 2. Use a 7/64” balldriver to install the landing gear on the fuselage withtwo 6-32” x 1/2” socket head bolts and #6 steel washers. The landing gearhas a slight sweep and it should be installed on the model angled forward.Threadlock may be used to prevent the bolts from loosening in flight.Required tools and adhesives:7/64” balldriver Thin CADremel rotary tool w/ cutoff wheel #0 Philips screwdriver1/16 in (1.5mm) drill bit ThreadlockPin drillFelt-tip penΟ Ο 1. The axles as supplied are suitable for the optional float kit installation(EFLA500) and require trimming for use with wheel pants. Cut off the exposedportion of the axle leaving approximately 1/4” protruding from the wheelcollar. Approximately 1” total axle length is the longest that will fit within thewheel pant. A cutoff wheel in a rotary tool works well for this. Do this for bothmain axles.Ο Ο 3. Locate the wheel pant on the landing gear and mark the hole locationswith a felt-tip pen. The trim lines on the wheel pant and fuselage can be usedto align the parts to each other. For another method see the E-tip on page 6.5
Page 1: WeihnachtsfeierZur diesjährigen We
Page 7 and 8: Required PartsFuselageVertical stab
Page 9 and 10: Ο Ο 4. Remove the servo arm using
Page 11 and 12: Receiver InstallationRequired Parts
Page 13 and 14: Motor and Battery InstallationE-fli
Page 15 and 16: Cowling, Propeller and Spinner Inst
Page 17 and 18: Wing JoiningRequired PartsWing halv
Page 19 and 20: Ο 8. Install the dihedral joiners
Page 21 and 22: Ο Ο 6. Using a #1 Philips screwdr
Page 23 and 24: Optional Float Installation.Require
Page 25 and 26: Ο 7. Install the rudder assembly,
Page 27 and 28: Flight PreparationControl Direction
Page 29 and 30: 25-Size Float SetOptional ItemsE-fl
Page 31 and 32: Lithium Polymer Battery Pack Inform
Page 33 and 34: AMA National Model Aircraft Safety
Page 35 and 36: Inspection or RepairsIf this Produc

Pulse XT 25e Manual - E-flite

Create successful ePaper yourself

Delete template?

Save as template?