ODU MAC

More documents

Recommendations

Info

Crimp ToolsCrimp Tools and Contact PreparationCrimping creates an easy, reliable, corrosion-free, and long-term connection between conductor and contact.It requires little skill and can be performed by non-experts.Crimping causes cold-flow of the conductor and contact material creating a gas-tight connectionbetween contact and conductor. A stiffening of the conductor at the connection, as it is possiblewith soldering, can not occur. Crimping can be performed on very small or very large conductor cross sections.For smaller cross sections (0.5 - 2.5 mm 2 ) an industry-standard 8-point crimp tool is used. Largercross sections require a hexagonal crimp press. For very large cross section the crimp procedure hasto be done in several steps to assure good cold-flow of the conductor material and to avoid a brittle connection.8-Crimp Tool. Adjustable for cross section from 0.08 - 0.5 mm 2 (AWG28 - AWG20)Table for adjustment and Contact holder = positioner - see page 46/47Order Number: 080 000 037 000 0008-Crimp Tool. Adjustable for cross section from 0.38 - 2.5 mm 2 (AWG22 - AWG12)Table for adjustment and Contact holder = positioner - see page 46/47Order Number: 080 000 038 000 000Crimp Instruction (for above tools)Correct crimp position will be attained by use of different Positioner.By rotating the selector knob to selected number you will get the correctcrimp connection.The crimp tool has an internal ratchet which opens only after completingthe crimp process.Page 48<strong>ODU</strong> Steckverbindungssysteme GmbH & Co. KG, Pregelstr. 11, D-84453 Mühldorf/Inn, Tel. +49/86 31/61 56-0, Fax +49/86 31/61 56 49, www.odu.de
Crimp Tools8-Crimp Tool. Adjustable for cross section from 0.08 - 2.5 mm 2 (AWG28 - AWG12)Gauge on request.Table for adjustment and Contact holder = positioner - see page 46/47The crimp tool has an internal ratchet which opens only after completing the crimpprocess.Order Number: 080 000 014 000 0008-Crimp Tool with pneumatic activation.Adjustable for cross section from 0.08 - 2.5 mm 2 (AWG28 - AWG12)Gauge on request.Table for adjustment and Contact holder = positioner - see page 36/37Order Number: 080 000 032 000 000Crimp Instruction (for above tools)How to set the crimp tool according to the cable cross-section1. Close crimp tool completely and keep it closed.2. Adjust the tool so that the smaller gauge-pin just fits through the hole but notso the bigger one. In order to achieve that you have to adjust the tool with theadjustment bolt. After the tool is set properly you have to secure it with thefastening screw in order to avoid a misadjustment by accident.3. Check the proper setting after a while by use of both gauge-pins.<strong>ODU</strong> Steckverbindungssysteme GmbH & Co. KG, Pregelstr. 11, D-84453 Mühldorf/Inn, Tel. +49/86 31/61 56-0, Fax +49/86 31/61 56 49, www.odu.de Page 49
Page 1: Catalogue No. 1004-dODU MACModular
Page 4 and 5: ODU MACProduct description:The ODU
Page 6 and 7: ODU MACThe ModulesThe insulation bo
Page 8 and 9: ModulesModule, 10 Positionsfor turn
Page 10 and 11: ModulesModule, for Print, Wire Wrap
Page 12 and 13: ModulesModule 14 PositionsSpacer (B
Page 14 and 15: ModulesModule 4 PositionsModule, 4
Page 16 and 17: ModulesModule 3 PositionsSpacer (Bl
Page 18 and 19: ModulesModule 4 Positionsfor high v
Page 20 and 21: ModulesModule 2 Positionsfor 50 Ω
Page 26 and 27: ModulesModule for compressed air va
Page 28 and 29: ModulesModule 2 Positions for Fiber
Page 30 and 31: Aluminum FrameODU MAC-S Aluminum Fr
Page 32 and 33: Aluminum FrameODU MAC-L Aluminum Fr
Page 34 and 35: ODU MACFor your notes:Page 34ODU St
Page 36 and 37: Solid FrameODU-MAC frame for DIN ho
Page 38 and 39: DIN HousingODU MAC DIN HousingPanel
Page 40 and 41: DIN HousingODU MAC DIN HousingBox-M
Page 42 and 43: DIN HousingODU-MAC Spindle Locking
Page 44 and 45: DIN HousingEMV housing(on request)A
Page 46 and 47: Crimp ToolsCrimp InstructionsTermin
Page 50 and 51: Crimp ToolsHexagonal Crimp Tool for
Page 52 and 53: Crimp ToolsStripper-Crimper for aut
Page 54 and 55: Crimp InstructionsAdjustment of the
Page 56 and 57: Technical InformationExplanations o
Page 58 and 59: Technical InformationCreepage dista
Page 60 and 61: ApplicationsTestsystem for AirbusBe
Page 62 and 63: ApplicationsOP of the futureFor the
Page 64 and 65: Technical ArticleConnection during
Page 66 and 67: Technical ArticleIn Figure 4 one se
Page 68 and 69: Technical ArticleIn practice, it ha
Page 70 and 71: Technical ArticleExample: Testing i
Page 72: ODU’s headquarters andfactory are

ODU MAC

Create successful ePaper yourself

Delete template?

Save as template?