ODU MAC

More documents

Recommendations

Info

Crimp InstructionsAdjustment of the Crimp Tong 080.000.014.000.000(see page 49)Required Tools:Crimp Tong (Type 014)SpannerPositionierGauge Pins1. Fasten the Positionier on the Crimp TongPlease insert the positionier into the tong.Attention: The positionier is labled with a "S"(=Socket) on the one, and with a "P" (=Pin) on theother side. So if your contact is a socket, so pleaseinsert the S-face into the tong. If your contact is a pin,so please insert the P-face into the tong.Now you have to insure the positionier with a clamp.Fix the clamp with the screw driver.2. Adjustment of the Crimp Tong for the cable cross sectionAt first you have to loose the securing nut of thesetscrew. Therefore please use the attached spanner.With turning on the setscrew you can adjust the cablecross section. Therfore you have to close the crimp tongcompletely.With the gauge pins you have to prove the cable crosssection. If the smaller gauge pin fit trough the hole in thecrimp dies, and the bigger one not, the the tong is readyadjusted. Please insure the adjustment with the securingnut.Now you can start with the crimp process.Page 54<strong>ODU</strong> Steckverbindungssysteme GmbH & Co. KG, Pregelstr. 11, D-84453 Mühldorf/Inn, Tel. +49/86 31/61 56-0, Fax +49/86 31/61 56 49, www.odu.de
Technical InformationCrimp TerminationAccording to DIN IEC 352Pull-out forces diagram of a crimp terminationaccording to the wire cross-section(Extract of DIN 352 – part 2)Wire Cross-section in mm 2Example: For a 2.5 mm 2 wire a minimum pull-out force of appr. 320 N is required<strong>ODU</strong> Steckverbindungssysteme GmbH & Co. KG, Pregelstr. 11, D-84453 Mühldorf/Inn, Tel. +49/86 31/61 56-0, Fax +49/86 31/61 56 49, www.odu.de Page 55
Page 1:
Catalogue No. 1004-dODU MACModular
Page 4 and 5: ODU MACProduct description:The ODU
Page 6 and 7: ODU MACThe ModulesThe insulation bo
Page 8 and 9: ModulesModule, 10 Positionsfor turn
Page 10 and 11: ModulesModule, for Print, Wire Wrap
Page 12 and 13: ModulesModule 14 PositionsSpacer (B
Page 14 and 15: ModulesModule 4 PositionsModule, 4
Page 16 and 17: ModulesModule 3 PositionsSpacer (Bl
Page 18 and 19: ModulesModule 4 Positionsfor high v
Page 20 and 21: ModulesModule 2 Positionsfor 50 Ω
Page 26 and 27: ModulesModule for compressed air va
Page 28 and 29: ModulesModule 2 Positions for Fiber
Page 30 and 31: Aluminum FrameODU MAC-S Aluminum Fr
Page 32 and 33: Aluminum FrameODU MAC-L Aluminum Fr
Page 34 and 35: ODU MACFor your notes:Page 34ODU St
Page 36 and 37: Solid FrameODU-MAC frame for DIN ho
Page 38 and 39: DIN HousingODU MAC DIN HousingPanel
Page 40 and 41: DIN HousingODU MAC DIN HousingBox-M
Page 42 and 43: DIN HousingODU-MAC Spindle Locking
Page 44 and 45: DIN HousingEMV housing(on request)A
Page 46 and 47: Crimp ToolsCrimp InstructionsTermin
Page 48 and 49: Crimp ToolsCrimp Tools and Contact
Page 50 and 51: Crimp ToolsHexagonal Crimp Tool for
Page 52 and 53: Crimp ToolsStripper-Crimper for aut
Page 56 and 57: Technical InformationExplanations o
Page 58 and 59: Technical InformationCreepage dista
Page 60 and 61: ApplicationsTestsystem for AirbusBe
Page 62 and 63: ApplicationsOP of the futureFor the
Page 64 and 65: Technical ArticleConnection during
Page 66 and 67: Technical ArticleIn Figure 4 one se
Page 68 and 69: Technical ArticleIn practice, it ha
Page 70 and 71: Technical ArticleExample: Testing i
Page 72: ODU’s headquarters andfactory are
show all

ODU MAC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?