Manual optoNCDT ILR 1181-1182 - Micro-Epsilon

More documents

Recommendations

Info

Control Commands7.2i7.2.1ModesThe sign ESC (1Bh) finishes the data output. Now the sensor waits for a new command.DT......DistancetrackingEssential input parameters: SA, SD, SE, SF, ST, OFEffect on:RS232/RS422, digital switching output, analog output-- Distance measurement at different kinds of surfaces (varying reflectance).-- Permanent evaluation of the sensitive laser radiation.• changing reflectance: longer measuring time• sudden jumps in distance: longer measuring timeThe minimum time to measure is 160 ms, the maximum time is 6 s. If the measuring signal fails to reach aspecified quality within six seconds, an error message is output.The time to measure may also be limited by setting the ST parameter to a desired value.7.2.2 DS ...... 7 m Distance TrackingEssential input parameters:Effect on:SA, SD, SE, SF, ST, OFRS232/RS422, digital switching output, analog output-- Distance measurement at different kinds of surfaces at close range up to 7 m-- Higher measurement rate compared to DT measuring mode.-- Within the range from 0.1 m to 0.5 m, measuring accuracy is restricted.Measuring time (time to measure) can be limited via ST parameter settings.optoNCDT ILR 1181 / 1182Page 28
Control Commands7.2.3DW......Distance Tracking with Cooperative Target (10 Hz)The command is only relevant for the ILR 1181.Essential input parameters:Effect on:SA, SD, SE, SF, OFRS232/RS422, digital switching output, analog output-- Performs at a steady measuring rate of 10 Hz.-- Stable measuring values only with a white target board at the target.-- No sudden jumps in distance > 16 cm.7.2.4DX......Distance Tracking with Cooperative TargetThe command is only relevant for the ILR 1182.Essential input parameters:SA, SD, SE, SF, OFEffect on:RS232/RS422, digital switching output, analog output-- Performs at a steady measuring rate of 50 Hz.-- Stable measuring values only with a white target board at the target.-- Homogeneous motions with maximum 4 m/s.-- High rate of measurement, included preceding measuring values in the process to calculate a currentlymeasuring value.-- No sudden jumps in distance >16 cm.7.2.5 DF......Distance Measurement with External TriggerEssential input parameters:Effect on:SD, SE, SF, ST, OF, TDRS232/RS422, digital switching output, analog output-- Preparation for the single measurement, triggered by an external trigger pulse.Initially, after selecting this mode, the operator does not receive any response. As soon as the trigger pulsehas been detected, the sensor will send data and switches the digital and/or the analog output.The Settings for the trigger delay (delay) and the trigger flank can be defined via parameter TD, see Chap.7.3.13.optoNCDT ILR 1181 / 1182Page 29
Page 1 and 2: Instruction ManualoptoNCDT ILR 1181
Page 3 and 4: optoNCDT ILR 1181 / 1182Contents1.
Page 5 and 6: Safety1.SafetyThe handling of the s
Page 7 and 8: Safety1.4Proper Use-- The sensors a
Page 9 and 10: Functional Principle, Technical Dat
Page 11 and 12: Functional Principle, Technical Dat
Page 13 and 14: Installation5. InstallationThe sens
Page 15 and 16: InstallationReflectorReflectorRefle
Page 17 and 18: InstallationwhiteTxDbrown RxDviolet
Page 19 and 20: Operation6.1optoNCDT ILR 1181 / 118
Page 21 and 22: Operation6.3 Digital Switching Outp
Page 23 and 24: Operation6.4 Analog OutputPropertie
Page 25 and 26: Operation6.5 Trigger InputPropertie
Page 27: Control CommandsTMBRASOFSOPAPRQueri
Page 31 and 32: Control CommandsoptoNCDT ILR 1181 /
Page 33 and 34: Control Commands7.3.6 SEx......Disp
Page 35 and 36: Control CommandsThe use of RMparame
Page 37 and 38: Control CommandsExample:TD1000_0[En
Page 39 and 40: Control Commands7.3.17 OFx.x.....Di
Page 41 and 42: Control Commands7.3.20PR......Reset
Page 43 and 44: HyperterminalFig. 24 Definition of
Page 45 and 46: Online Help Tool9. Online Help Tool
Page 47 and 48: TroubleshootingE53One or more param
Page 49 and 50: Factory Setting13.Factory SettingPa
Page 52: MICRO-EPSILON MESSTECHNIK GmbH & Co

Manual optoNCDT ILR 1181-1182 - Micro-Epsilon

Create successful ePaper yourself

Delete template?

Save as template?