Probing Systems For Co-ordinate Measuring machines - Teknikel

More documents

Recommendations

Info

Probing systems forco-ordinate measuring machinesTP200 stylus moduleM8 × 1.25 threadThe stylus module is mounted on the probeTouch-trigger probeswith stylus module changing3-2via a highly repeatable magnetic kinematicjoint, providing a rapid stylus changingcapability and probe overtravel protection.There are three modules available, with twodifferent overtravel forces:• The SF (standard force) module issuitable for most applications.• The LF (low force) module isrecommended for use with small precisionball styli or on delicate materials.• The EO (extended overtravel) moduleis recommended for use whenincreasing the speed of the CMMmay lead to stopping distances whichexceed the overtravel range providedin the SF/LF modules. The EO modulehas an additional 8 mm (0.32 in) ofovertravel in the probe Z axis to protectagainst damage to the sensor in suchcircumstances. Overtravel force is thesame as the SF module.Status LEDsØ13.5 mm(0.53 in)4 mm(0.16 in)M2 × 0.4 thread14° 14°MaximumXY overtravelKinematicplane5 mm(0.20 in)30 mm(1.18 in)SF/LF 13 mm (0.51 in)EO 24 mm (0.95 in)module notshownSF/LF 4.5 mm (0.18 in)EO 12.5 mm (0.49 in)+Z overtravel4 mm (0.16 in)-Z overtravel by separation ofthe module from the sensorPI 200 probe interfaceThe PI 200 is a unit capable of the automaticrecognition and interfacing of TP200/B and alsoconventional touch-trigger probes (TP2, TP6,TP20). Two switchable levels of probe triggersensitivity are provided to accommodate differingapplications. The PI 200 interface is covered fullyin section 9.PI 200SCR200 stylus changing rackThe SCR200 provides rapid, automatic changingof stylus modules without the need to re-qualifystylus tips. The SCR200 is powered entirely bythe PI 200 and provides features to facilitate safestylus changing.245 mm (9.65 in)MSR1 module storage rackFor manual storage of modules - see section 13.Probe maintenanceCK200 (Renishaw part number A-1085-0016) isa specialised cleaning material supplied for theremoval of contamination from the location facesof the magnetically retained kinematic couplingsof the TP20, TP200 and SP25M probe systems.The frequency of cleaning should be determinedaccording to the conditions of use.190 mm (7.84 in)SCR200
TP200 / TP200B features and benefits:• Excellent repeatability and precision 3D formmeasurement• Rapid exchange between stylus confi gurationswithout the need to re-calibrate• 6-way measuring capability (±X, ±Y, ±Z)• SF and LF modules to give overtravel force to suitthe application• EO module to give increased overtravel in probeZ axis• Zero reseat errors and no lobing effect• Suitable for intensive ‘peck’ or ‘stitch’ scanning• Stylus reach up to 100 mm (3.99 in) GF rangeTouch-trigger probeswith stylus module changing3-3• Module life of >10 million triggers• Compact size• Compatible with the full range of Renishaw probeheads and accessoriesSpecification summary TP200 TP200BPRINCIPAL APPLICATIONDCC CMM where high accuracyis required.As TP200 but where ‘air’* triggerevents occur.SENSE DIRECTIONS 6-axis: ±X, ±Y, ±Z 6-axis: ±X, ±Y, ±ZUNIDIRECTIONAL REPEATABILITY(2σ µm)Trigger level 1Trigger level 20.40 µm (0.000016 in)0.50 µm (0.00002 in)0.40 µm (0.000016 in)0.50 µm (0.00002 in)XY (2D) FORM MEASUREMENTDEVIATIONTrigger level 1Trigger level 2±0.80 µm (0.000032 in)±0.90 µm (0.000036 in)±1 µm (0.00004 in)±1.2 µm (0.000047 in)XYZ (3D) FORM MEASUREMENTDEVIATIONTrigger level 1Trigger level 2±1 µm (0.00004 in)±1.40 µm (0.000056 in)±2.50 µm (0.0001 in)±4 µm (0.00016 in)REPEATABILITY OF STYLUSCHANGEWith SCR200Manual±0.50 µm (0.00002 in) max.±1 µm (0.00004 in) max.±0.50 µm (0.00002 in) max.±1 µm (0.00004 in) max.TRIGGER FORCE(at stylus tip)XY planeZ axisAll modulesAll modules0.02 N0.07 N0.02 N0.07 NOVERTRAVELFORCE(@ 0.50 mmdisplacement)XY planeZ axisSF/EO moduleLF moduleSF/EO moduleLF module0.2 N to 0.4 N0.1 N to 0.15 N4.90 N1.60 N0.2 N to 0.4 N0.1 N to 0.15 N4.90 N1.60 NWEIGHT (probe sensor and module) 22 g (0.78 oz) 22 g (0.78 oz)MAXIMUM EXTENSION (if on a PH10 series head) 300 mm (11.81 in) 300 mm (11.81 in)MAXIMUM RECOMMENDEDSTYLUS LENGTH(M2 styli range)SF/EO moduleLF module50 mm (1.97 in) steel to100 mm (3.94 in) GF20 mm (0.79 in) steel to50 mm (1.97 in) GF50 mm (1.97 in) steel to100 mm (3.94 in) GF20 mm (0.79 in) steel to50 mm (1.97 in) GFMOUNTING METHOD M8 thread M8 threadSUITABLE INTERFACE PI 200, UCC PI 200, UCCSTYLUS MODULE CHANGINGRACKAutomaticManualSCR200MSR1SCR200MSR1Above data applies for test conditions as follows: Stylus length 50 mm (1.97 in) Stylus velocity 480 mm/min (1.57 ft/min).* Air trigger (or false trigger). The TP200B reduces probe triggers that may be caused by vibrations.
Page 1 and 2: CMM products technical specificatio
Page 3 and 4: Probing systems forco-ordinate meas
Page 5 and 6: Step 3 (see sections 5/6/7/8)Probe
Page 7 and 8: TP2-5W probesM8 × 1.25 threadThe T
Page 9: TP200 / TP200B modular probesThe TP
Page 13 and 14: TP20 stylus moduleThe TP20 stylus m
Page 15 and 16: Specification summary (2)Module App
Page 17 and 18: SP25M modular componentsystemSP25M
Page 19 and 20: Automation using the FCR25 flexible
Page 21 and 22: Specification summary SP25MPROBE AT
Page 23 and 24: SP80 probe bodySP80 probe kitThe se
Page 25 and 26: SP80 features and benefits:• Ultr
Page 27 and 28: SH600 STD / SH600 EXT stylus holder
Page 30 and 31: Q24885Probing systems forco-ordinat
Page 60 and 61:
Probing systems forco-ordinate meas
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86:
show all

Probing Systems For Co-ordinate Measuring machines - Teknikel

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?