Probing Systems For Co-ordinate Measuring machines - Teknikel

More documents

Recommendations

Info

Probing systems forco-ordinate measuring machinesTP20 / TP20 NI features andbenefits:Touch-trigger probeswith stylus module changing3-6• A kinematic touch-trigger probe systemfor manual and DCC CMMs• Rapid exchange between stylusconfi gurations without the need tore-calibrate• A choice of seven stylus modules,giving 5-axis or 6-axis operation,allow optimisation of probe and stylusperformance to the given application• Easily retrofi tted to all Renishawstandard probe heads (M8 or autojointfi tting) and compatible with existing TTPinterfaces• Metrology performance equivalent toindustry proven TP2-5W probe• Compatible with the full range ofRenishaw probe heads and accessoriesSpecification summary (1) TP20 TP20 NIPRINCIPAL APPLICATIONSENSE DIRECTIONSPRE-TRAVEL VARIATIONUNIDIRECTIONALREPEATABILITY (2σ µm)(at stylus tip)All modules except 6W6WLFSF/EM1/EM2MFEF6WSF/LF/EM1/EM2MFEF6WDCC and manual CMMs suitablefor most applications.5-axis: ±X, ±Y, +Z6-axis: ±X, ±Y, ±Z±0.60 µm (±0.000023 in)±0.80 µm (±0.000032 in)±1 µm (±0.000039 in)±2 µm (±0.000079 in)±1.50 µm (±0.000058 in)±0.35 µm (±0.000014 in)±0.50 µm (±0.000020 in)±0.65 µm (±0.000026 in)±0.80 µm (±0.000032 in)DCC and manual CMMs whereoperation is within a magneticfi eld.5-axis: ±X, ±Y, +Z6-axis: ±X, ±Y, ±Z±0.60 µm (±0.000023 in)±0.80 µm (±0.000032 in)±1 µm (±0.000039 in)±2 µm (±0.000079 in)±1.50 µm (±0.000058 in)±0.35 µm (±0.000014 in)±0.50 µm (±0.000020 in)±0.65 µm (±0.000026 in)±0.80 µm (±0.000032 in)±0.50 µm (±0.000020 in)±1 µm (±0.000040 in)REPEATABILITY OF STYLUSCHANGE (maximum)With MCR20Manual±0.50 µm (±0.000020 in)±1 µm (±0.000040 in)STYLUS RANGE M2 M2MOUNTING METHOD M8 thread M8 threadSUITABLE INTERFACE PI 4-2, PI 7-2, PI 200, UCC PI 4-2, PI 7-2, PI 200, UCCSTYLUS MODULEAutomatic MCR20MCR20CHANGING RACKManual MSR1MSR1Above data applies for test conditions as follows: Stylus length 10 mm (0.39 in). Stylus velocity 480 mm/min (1.57 ft/min)
Specification summary (2)Module Application guide Maximum extensionon PH10 series headLFSFEM1EM2MFEF6WThe low force stylus module, identifi ed by a green cap,is suited to applications that require low trigger force,e.g. rubber seals.The standard force stylus modules, identifi ed by blackcaps, are suited to the majority of applications.The medium force stylus module, identifi ed by a grey cap,is for use where a higher trigger force than standard isrequired.The extended force stylus module is identifi ed by a browncap. Typically, this stylus module will only be required withlarge stylus assemblies, and where spurious ‘air’ triggerscaused by machine vibration and acceleration, precludethe use of either SF, LF or MF modules.The 6-way stylus module, identifi ed by a blue cap, hasbeen designed for applications requiring measurement inthe –Z direction, for example when measuring the widthof undercuts.Weight(body and module)300 mm (11.81 in) 22 g (0.78 oz)300 mm (11.81 in)300 mm (11.81 in)*300 mm (11.81 in)*22 g (0.78 oz)28 g (0.99 oz)30 g (1.06 oz)300 mm (11.81 in) 22 g (0.78 oz)300 mm (11.81 in) 22 g (0.78 oz)300 mm (11.81 in) 22 g (0.78 oz)Touch-trigger probeswith stylus module changing3-7* NOTE: Dependant on CMM used and operating conditions.Specification summary (3)Module typeand textstylus lengthLF10 mmSFEM1EM210 mmMF25 mmEF50 mm6W10 mmTrigger force Overtravel force Overtravel displacementXY Z XY +Z -Z XY +Z -Z0.06 N 0.65 N 0.09 N 1.15 N - ±14°0.08 N 0.75 N0.10 N 1.9 N0.10 N 3.2 N0.20 N to0.30 N0.20 N to0.40 N0.20 N to0.50 N3.50 N - ±14°7 N - ±14°10 N - ±14°0.14 N 1.60 N 0.25 N 2.50 N 9 N ±14°3.10 mm(0.12 in)4 mm(0.16 in)3.70 mm(0.15 in)2.40 mm(0.09 in)4.50 mm(0.18 in)Above data applies for test conditions as follows: Stylus length as stated above. Stylus velocity 480 mm/min (1.57 ft/min)----1.50 mm(0.06 in)
Page 1 and 2: CMM products technical specificatio
Page 3 and 4: Probing systems forco-ordinate meas
Page 5 and 6: Step 3 (see sections 5/6/7/8)Probe
Page 7 and 8: TP2-5W probesM8 × 1.25 threadThe T
Page 9 and 10: TP200 / TP200B modular probesThe TP
Page 11 and 12: TP200 / TP200B features and benefit
Page 13: TP20 stylus moduleThe TP20 stylus m
Page 17 and 18: SP25M modular componentsystemSP25M
Page 19 and 20: Automation using the FCR25 flexible
Page 21 and 22: Specification summary SP25MPROBE AT
Page 23 and 24: SP80 probe bodySP80 probe kitThe se
Page 25 and 26: SP80 features and benefits:• Ultr
Page 27 and 28: SH600 STD / SH600 EXT stylus holder
Page 30 and 31: Q24885Probing systems forco-ordinat
Page 64 and 65:
Probing systems forco-ordinate meas
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86:
show all

Probing Systems For Co-ordinate Measuring machines - Teknikel

Create successful ePaper yourself

Delete template?

Save as template?