Autohelm Inboard Autopilots (ST6000 and ST7000 systems) Service ...

More documents

Recommendations

Info

Autohelm7. Service visit to a vesselWhen a service visit to a vessel is made the most common fault encountered is likelyto be poor connections or inadequate power supplies. These should be thoroughlychecked before the service visit diagnostic procedure is carried out. When trying tolocate a fault it should be remembered that most failures will occur in the CourseComputer with the Control Units as the next most likely.It should be noted that the calibration variables and auto deviation correction willrequire re-setting if either the course computer, its PCB or its Software areexchanged. Similarly if the Control Unit PCB is exchanged the display contrast willrequire re-setting. Procedures for carrying out both these operations are given insection 3.Always note the course computer calibration settings before removing from thevessel.22SeaTalk Service Manual
Autohelm7.1 Service Visit - Diagnostic ProcedureOn arrival check for bad connections and for inadequate power supplies. If the system stillexhibits a fault, then use the diagnostic procedure outlined below.SeaTalk Service Manual 23
Page 1 and 2:
AutohelmAutohelm Inboard Autopilots
Page 3:
AutohelmST7000 SystemMaster Table o
Page 6 and 7:
AutohelmST7000 System IndexPage1. I
Page 8 and 9:
Autohelm3. Operating/Calibration in
Page 10:
AutohelmDisplay Key SequenceWatch A
Page 13 and 14:
AutohelmUnsatisfactory Steering Per
Page 15 and 16:
AutohelmWind Change AlarmWind Trim
Page 17 and 18:
AutohelmAdjusting CalibrationIn cal
Page 19 and 20:
Autohelm3. 5 Automatic Deviation Co
Page 21 and 22:
Autohelm5. Track Control interfacin
Page 23 and 24:
Autohelm6. Special functions.6.1 Di
Page 25:
Autohelm7.1 Service Visit - Diagnos
Page 28 and 29:
AutohelmContentsPage1. Description
Page 30 and 31:
Autohelm5. When finally refitting t
Page 32 and 33:
AutohelmLCD Display Assembly6SeaTal
Page 34 and 35:
Autohelm8SeaTalk Service Manual
Page 36 and 37:
Page 38 and 39:
Autohelm1. Control Unit PCB Circuit
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46:
Page 49 and 50: ST7000 Course Computer General Asse
Page 51 and 52: Autohelm4. Functional TestThe Cours
Page 53 and 54: AutohelmSeaTalk Service Manual 9
Page 59 and 60: Autohelm4.3 Course Computer Bench T
Page 61 and 62: Autohelm2. Technical InformationCon
Page 63 and 64: Autohelm1.4. Clutch DriveTR10, 11 a
Page 65: AutohelmFig. 1. ST7000 (Z083 and Z0
Page 68 and 69: Autohelm8SeaTalk Service Manual
Page 80 and 81: AutohelmContentsPage1. Introduction
Page 82 and 83: Autohelm3. Operating/Calibration In
Page 84 and 85: AutohelmDisplay Key SequenceThe Dis
Page 86 and 87: AutohelmWatch Alarm (not available
Page 88 and 89: Autohelm3.2 Additional information
Page 90 and 91: Autohelm3.3 Operating HintsResponse
Page 92 and 93: Autohelm• If the autopilot fails
Page 94 and 95: Autohelm3.4.1 Adjusting Calibration
Page 96 and 97: Autohelm3.5 Automatic Deviation Cor
Page 98 and 99: Autohelmmessage indicates the ST600
Page 104 and 105: Autohelm1. Service ProceduresConten
Page 106 and 107: Autohelm5. Pull the loom assemblies
Page 108 and 109: Autohelm4. Z124 Control Unit Functi
Page 110 and 111: Autohelm5. Product History - Contro
Page 112 and 113: Autohelm1. Control Unit PCB Circuit
Page 120 and 121: AutohelmContentsPage1. Description
Page 122 and 123: AutohelmCourse Computers (Z083, Z08
Page 124 and 125: Autohelm4.1 Course Computer Bench T
Page 128 and 129: Autohelm5. Product History - Course
Page 130 and 131: Autohelm1. ST 6000 Course Computer
Page 140 and 141: AutohelmContentsPage1. Description
Page 142 and 143: Autohelm3. Operation with non Autoh
Page 144 and 145: Autohelm1. Type CR Interface Box PC
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
AutohelmZ131 Rudder Reference Body
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
AutohelmZ130 Fluxgate General Assem
Page 162 and 163:
Autohelm6. Before installing the co
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
AutohelmFig. 1. Rudder Reference Un
Page 174 and 175:
Autohelm3. Product History Rudder R
Page 176 and 177:
Page 178 and 179:
Autohelm4. Product History (Z080 Ma
Page 180 and 181:
AutohelmZ050 Mount Assembly6SeaTalk
Page 182 and 183:
AutohelmContentsPage1. Linear Drive
Page 184 and 185:
AutohelmSlide off the carrier assem
Page 186 and 187:
Autohelm* No load current limits :-
Page 188 and 189:
Autohelm7. Product History Type 2 L
Page 190 and 191:
Page 192 and 193:
AutohelmContentsPage1. Rotary Drive
Page 194 and 195:
Autohelmb) When rebuilding the clut
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
AutohelmContentsPage1. Hydraulic Dr
Page 202 and 203:
Autohelmc) If the relief valve asse
Page 204 and 205:
Autohelm3. Reversing Gear Pumps (Z0
Page 206 and 207:
Autohelm4. Type'0'Piston Pump (Z081
Page 208 and 209:
Page 210 and 211:
AutohelmContentsPage1. I/O Drive Un
Page 212 and 213:
Autohelm4. Spares numbers - I/O Ste
Page 214:
Autohelm- Position the support plat
show all

Autohelm Inboard Autopilots (ST6000 and ST7000 systems) Service ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?