Emotron VFX/FDU 2.0

More documents

Recommendations

Info

3.1.1 CoolingTable below shows the minimum free space required aroundthe AFR and/or VSI cabinets in order to guarantee adequatecooling. Because the fans blow the air from the bottom to thetop it is advisable not to position an air inlet immediatelyabove an air outlet.The following minimum separation between two cabinets ora cabinet and a non-dissipating wall must be maintained.Valid if free space on opposite side.3.2.2 Mounting schemesNOTE: When a cabinet is placed between two walls, aminimum distance at each side of 200 mm must bemaintained.3.2 Cabinet mounting3.2.1 CoolingIf the AFR or VSI is installed in a cabinet, the rate of airflowsupplied by the cooling fans must be taken intoconsideration. Frame sizes are listed in chapter 11.1 page 51.Table 5Flow rates cooling fansFrame Model Flow rate [m 3 /hour]E46 175 510F46 250F69* 175800G46 375 1020H46 500H69* 3751600I46 750I69* 5002400J46 1000J69* 6503200K46 1500K69* 10004800Fig. 9 VFXR/FDUL46: Model 146 to 250*Preliminary data.NOTE: For the models 1000 to 1500 the mentionedamount of air flow should be divided equally over the twocabinets.Fig. 10 VFXR/FDUL46: Model 300 to 50014 Mounting Emotron AB 01-5076-01r1
4. InstallationThe description of installation in this chapter complies withthe EMC standards and the Machine Directive.Select cable type and screening according to the EMCrequirements valid for the environment where the AFR andVSI is installed.!CAUTION!Allways consult Emotron before connectingan AFR to a standard AC drive.4.1 Before installationRead the following checklist and prepare for yourapplication before installation.• Local or remote control.• Functions used.• Suitable AFR and VSI size in proportion to the motor/application.• Mount separately supplied option boards according tothe instructions in the appropriate option manual.If the AFR and AC drive is temporarily stored before beingconnected, please check the technical data for environmentalconditions. If the AFR and VSIis moved from a cold storageroom to the room where it is to be installed, condensationcan occur on it. Allow the AFR and VSI to become fullyacclimatised and wait until any visible condensation hasevaporated before connecting the mains voltage.4.2 Connect motor and mains4.2.1 Single drivesAFEVSIBlankpanelControlpanel forAFEMains connectionMotor connectionL1, L2, L3 U, V, WFig. 11 Connecting motor and mains cables forVFXR/FDUL46 - 146 to 250Table 6L1,L2,L3PEU, V, WDC-,DC+Mains and motor connectionMains supply, 3 -phaseSafety earth (protective earth)Motor earthMotor output, 3-phaseDC-linkconnections (optional)Emotron AB 01-5076-01r1 Installation 15
Page 1: Emotron VFX/FDU 2.0AFE - Active Fro
Page 6 and 7: CondensationIf the active front end
Page 8: 2 Emotron AB 01-5076-01r1
Page 13 and 14: 2. General descriptionEmotron AFR i
Page 15 and 16: 2.2 Emotron AFR cabinet concept2.2.
Page 18 and 19: 12 General description Emotron AB 0
Page 23 and 24: 5. Control Connections for Emotron
Page 25 and 26: RITTALRITTALRITTALRITTALRITTALRITTA
Page 27 and 28: 6. Getting StartedThis chapter is a
Page 29 and 30: Table 9Default parameter setup for
Page 31 and 32: 7. EMC and Machine Directive7.1 EMC
Page 33 and 34: 8. Operation via the Control PanelT
Page 35 and 36: 8.3.3 LED indicatorsThe symbols on
Page 37 and 38: 8.4 The menu structureThe menu stru
Page 39 and 40: 9. Functional Description for AFR u
Page 41 and 42: Reset Control [216]When the AFR is
Page 43 and 44: Reactive power [714]Displays the ac
Page 45 and 46: 9.8 System Data [900]Main menu for
Page 47 and 48: 9.9.3 Udc controller oparameters[O3
Page 49 and 50: 9.9.7 View control status [O90]Udc
Page 51 and 52: 10. Troubleshooting, Diagnoses and
Page 53 and 54: Table 18Trip condition, their possi
Page 55 and 56: 10.3 MaintenanceThe variable speed
Page 57 and 58: 11. Technical Data11.1 Electrical a
Page 59 and 60: Table 22 AFR69 typical output DC po
Page 61 and 62: 11.3 Operation at highertemperature
Page 64 and 65: DEFAULTCUSTOMDEFAULTCUSTOM615 CD Se
Page 66: Emotron AB, Mörsaregatan 12, SE-25

Emotron VFX/FDU 2.0

Create successful ePaper yourself

Delete template?

Save as template?