Emotron VFX/FDU 2.0

More documents

Recommendations

Info

9.1.2 2nd Line [120]Sets the content of the lower row in the menu [100]Preferred View. Same selection as in menu [110].Default:Torque9.2 Main Setup [200]The Main Setup menu contains the most important settingsto get the AFR operational and set up for the application. Itincludes different sub menus concerning the control of theunit, protection, utilities and automatic resetting of faults.This menu will instantaneously be adapted to build inoptions and show the required settings.9.2.1 Operation [210]Selections concerning the control signals and serialcommunication are described in this submenu and is used toset the AFE up for the application.Language [211]Select the language used on the LC Display. Once thelanguage is set, this selection will not be affected by the LoadDefault command.Default:EnglishEnglish 0 English selectedSvenska 1 Swedish selectedNederlands 2Dutch selectedDeutsch 3 German selectedFrançais 4 French selectedEspañol 5 Spanish selectedРуccкий 6 Russian selectedItaliano 7 Italian selectedČesky 8 Czech selected120 2nd LineStpATorqueTurkish 9 Turkish selected211 LanguageStp A EnglishReference control [214]To control the reactive power of the AFE needs a referencesignal. This reference signal can be controlled by a remotesource from the installation, the keyboard of the AFR, or byserial or fieldbus communication. Select the requiredreference control for the application in this menu.Default:Remote 0Keyboard 1Com 2KeyboardThe reference signal comes from the analogueinputs of the terminal strip (terminals1-22).Reference is set with the + and - keys onthe Control Panel. Can only be done inmenu Set/View reference [310].The reference is set via the serial communication(RS 485, Fieldbus.) See Fieldbusor RS232/485 option manual for details.NOTE: If the reference is switched from Remote toKeyboard, the last remote reference value will be thedefault value for the control panel.Run/Stop Control [215]This function is used to select the source for run and stopcommands.Default:Remote 0214 Ref ControlStpAKeyboard215 Run/Stp CtrlStpAKeyboardKeyboardThe start/stop signal comes from the digitalinputs of the terminal strip (terminals 1-22).Keyboard 1 Start and stop is set on the Control Panel.Com 2The start/stop is set via the serial communication(RS 485, Fieldbus.) See Fieldbus orRS232/485 option manual for details.34 Functional Description for AFR unit Emotron AB 01-5076-01r1
Reset Control [216]When the AFR is stopped due to a failure, a reset commandis required to make it possible to restart the AFR. Use thisfunction to select the source of the reset signal.Default:Remote 0Keyboard 1Com 2Remote +KeybCom +KeybRem+Keyb+Com345216 Reset CtrlStpAKeyboardKeyboardThe command comes from the inputs ofthe terminal strip (terminals 1-22).The command comes from the commandkeys of the Control Panel.The command comes from the serialcommunication (RS 485, Fieldbus).The command comes from the inputs ofthe terminal strip (terminals 1-22) or thekeyboard.The command comes from the serialcommunication (RS485, Fieldbus) or thekeyboard.The command comes from the inputs ofthe terminal strip (terminals 1-22), thekeyboard or the serial communication(RS485, Fieldbus).Local/Remote key function [217]Please refer to the Instruction manual for Emotron VFX/FDU 2.0 for further information.Lock Code [218]Please refer to the Instruction manual for Emotron VFX/FDU 2.0 for further information.Remote signal Level/Edge [21A]Please refer to the Instruction manual for Emotron VFX/FDU 2.0 for further information.9.2.2 Motor Protection [230]Please refer to the Instruction manual for Emotron VFX/FDU 2.0 for further information.9.2.3 Parameter Set Handling [240]Select Set [241]Here you select the parameter set.Note. The active front end unit only supports oneparameter set.Default:Selection:AAA 0 Fixed selection to parameter set AThe active set can be viewed with function [721] FI status.Load Default Values Into Set [243]With this function the factory setting can be selected for theparameter set. When loading the default settings, all changesmade in the software are set to factory settings.Default:A 0Factory 5241 Select SetStpAAOnly the selected parameter set will revertto its default settings.All settings, except [211], [261] and [923],will revert to the default settings.NOTE: Trip log hour counter and other VIEW ONLY menusare not regarded as settings and will be unaffected.NOTE: If “Factory” is selected, the message “Sure?” isdisplayed. Press the + key to display “Yes” and thenEnter to confirm.9.2.4 Trip Autoreset/Trip Conditions[250]Please refer to the Instruction manual for Emotron VFX/FDU 2.0 for further information.A243 Default>SetStpAA9.2.5 Serial Communication [260]Please refer to the Instruction manual for Emotron VFX/FDU 2.0 for further information.Emotron AB 01-5076-01r1 Functional Description for AFR unit 35
Page 1: Emotron VFX/FDU 2.0AFE - Active Fro
Page 6 and 7: CondensationIf the active front end
Page 8: 2 Emotron AB 01-5076-01r1
Page 13 and 14: 2. General descriptionEmotron AFR i
Page 15 and 16: 2.2 Emotron AFR cabinet concept2.2.
Page 18 and 19: 12 General description Emotron AB 0
Page 20 and 21: 3.1.1 CoolingTable below shows the
Page 23 and 24: 5. Control Connections for Emotron
Page 25 and 26: RITTALRITTALRITTALRITTALRITTALRITTA
Page 27 and 28: 6. Getting StartedThis chapter is a
Page 29 and 30: Table 9Default parameter setup for
Page 31 and 32: 7. EMC and Machine Directive7.1 EMC
Page 33 and 34: 8. Operation via the Control PanelT
Page 35 and 36: 8.3.3 LED indicatorsThe symbols on
Page 37 and 38: 8.4 The menu structureThe menu stru
Page 39: 9. Functional Description for AFR u
Page 43 and 44: Reactive power [714]Displays the ac
Page 45 and 46: 9.8 System Data [900]Main menu for
Page 47 and 48: 9.9.3 Udc controller oparameters[O3
Page 49 and 50: 9.9.7 View control status [O90]Udc
Page 51 and 52: 10. Troubleshooting, Diagnoses and
Page 53 and 54: Table 18Trip condition, their possi
Page 55 and 56: 10.3 MaintenanceThe variable speed
Page 57 and 58: 11. Technical Data11.1 Electrical a
Page 59 and 60: Table 22 AFR69 typical output DC po
Page 61 and 62: 11.3 Operation at highertemperature
Page 64 and 65: DEFAULTCUSTOMDEFAULTCUSTOM615 CD Se
Page 66: Emotron AB, Mörsaregatan 12, SE-25

Emotron VFX/FDU 2.0

Create successful ePaper yourself

Delete template?

Save as template?